Provides infrastructure for hardware re-configuration via Device Tree overlays

• introduce wb85x board config
• uarts on mod1 & mod2; wbmz actually not supported now (because of wb-ec firmware)
• wbmz5: fix temperature sensor display
• add wb8x support (on 7.4.x board)
• add dependency on linux-image-wb8

Linux kernel headers for 5.10.35-wb169 on armhf

• i2c-wbio: cherry-pick i2c bus recovery logic (mv64xxx driver)
• add CAN SAE J1939 support built-in

Wiren Board URRI receiver (MQTT driver)

• Fix receiver IP address validation

Reference MQTT-RPC implementation

• Fix exception processing

Wiren Board Configuration Editor Backend

• service: use /etc/default/wb-mqtt-confed
• Backup /etc/ntp.conf by moving to /mnt/data

Wiren Board Smart Home MQTT serial protocol driver

• Fix APC NMC2 AP9630 template
• Add template PID-controller Ptex
• Add new template for Veda VF 51
• Add template APC NMC2 AP9630
• WB-MRWM2 template: add support for startup delay, restart delay, voltage control function
• Add g-leakage group
• ONOKOM templates: fix units
• WB-MRM2-MINI template: add min request interval
• WB-MIR_V2 template: add min request interval
• WB-MAI2-CC template: add min request interval
• WB-MAI6 template: remove FW version
• Add min core voltage reg in wb-mir_v2 template
• Add min core voltage reg in wb-mai2-cc template
• Add min core voltage reg in wb-mr2m template
• Add IEC61107 Mode C protocol
• Add LUNA three-phase electricity meter template
• Add min core voltage reg in m1w2 template
• Somfy SDN: add tilting support
• Add new template for Carel muRack after rework
• Add indirect control channels for WB-MSW-v3/v4/v4-lora and WB-MIR-v2
• Add Energomera CE102 template
• Add channels "tariffs" to templates/config-mercury230.json
• WB-MAI6 template: add WB-VDIV and custom voltage divider support
• Add device address setup RPC
• Add new signature in m1w2 template
• Add GitHub pull request template. No functional changes
• Watch device template changes in /usr/lib/wb-mqtt-serial/templates
• Delete template for Carel muRack
• Add new template for Carel muRack
• Add device setup RPC
• Somfy SDN: speed adjustment is only available on DC motors
• Fix WB-MAI6 configuration interface
• WB-MDM3 template: add light scenes, switch mode, safety and powerup actions support
• Add new template for A-OK AM-35 motors
• Validation error of config containing duplicated ports
• Show template validation errors in log
• Add missed wb-utils dependency, no functional changes
• Add min_request_interval option to device config. The option defines minimal time between requests to a device
• Add mercury230 protocol description to README.md. No functional changes
• Jinjify WB_MWAC v1 template, add cleaning mode, safe state for alarm, fix debounce range, sporadic for alarm
• Publish error in /devices/+/meta/error on device disconnection
• Install missed wb-mqtt-serial.conf.wb8
• Add default config for wb8
• Fixed a crash caused by receiving a large number of incorrect Modbus packets
• Add more verbose internal errors. No functional changes
• Add temperature sensors poll period register for M1W2
• Add MQTT topic id to config/Load RPC response
• Add device signature to MAP3E, MAP3ET, MAP3EV templates
• Fix MAI11 slave id editor position in wb-mqtt-homeui
• Add device signature to WB-MWAC v.2 template
• Add new template for WB-Domofon
• Add new template for A-OK motors
• WB-M1W2 template: add button reset input counters
• Set correct default template for WB-MRPS6
• Fix SOKOL-M template
• Add protocol information to config loading RPC request

Wiren Board common packages

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Somfy and Dooya devices integration via RF-Blinds stick/wbe-module (from smarttone.ru).

• Fix CPU usage when no serial devices found

development files for testing libwbmqtt-based projects

Micron eMMC utility

• Fix changelog, no functional changes

development files for libwbmqtt

• Add missed control types (pressure, lux, sound_level)
• Add escaping for non Latin1 symbols in JSON

Wiren Board Rule Engine

• Fix parseInt() explicit radix 16 handling for leading zero
• Fix meta json unmarshaling, update wbgo.so library
• Alarms schema: disable Edit JSON
• update wbgo.so library: fix go.sum
• Fix stuck on reboot/stop, when multiple virtual devices update their meta
• update wbgo.so library
• bump PahoMQTT dep: v1.4.1 -> v1.4.2
• Fix control meta handling, update wbgo.so library
• Add missed control types, update wbgo.so library
• Add json editor autocomplete for devices

Wiren Board Cloud agent

• Handle TimeoutExpired exception during events polling
• Tweak curl params
• Fix preinst hook
• fix cloud connection status absense in UI if no providers configured
• Fix config search path
• Substitute mqtt broker url in telegraf config
• Move device certs check to ExecStartPre (instead of postinst)
• Backup config via wb-configs
• Send diagnostics to the cloud backend by request
• Fix service unit
• Add BROKER_URL config option and --broker launch argument for mqtt broker
• Fixes around cloud connection status
• Send agent version to the cloud backend
• Bugfix with cloud url in config
• Add multi-provider support

CLI for wb-mqtt-db

• Fix connection error handling

Wiren Board MQTT Driver for Welrok thermostat

wb-rules-based IIO DAC driver for WB MQTT

• Fix iio-device-num parsing

development files for testing libwbmqtt-based projects

• Add missed control types (pressure, lux, sound_level)
• Add escaping for non Latin1 symbols in JSON

Wiren Board MQTT to Modbus gateway

• Add option to prevent config regeneration
• Fix holding registers detection

knxd configurator for Wiren Board

• schema: fix Global.Error/Global.Trace format
• schema: remove Edit JSON buttons

Wiren Board Smart Home MQTT abstraction layer and utils library

• Add missed control types (pressure, lux, sound_level)
• Add escaping for non Latin1 symbols in JSON

Linux support headers for userspace development

• i2c-wbio: cherry-pick i2c bus recovery logic (mv64xxx driver)
• add CAN SAE J1939 support built-in

Wiren Board Smart Home MQTT generic 1-Wire (w1) driver compatible with HomA conventions

• Fix tests, no functional changes

Wirenboard essential packages

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Wiren Board modbus devices manager (python3 service; backend)

• Stop slow scan faster
• Add port path parameter to bus-scan/Start RPC request
• Do not stop the whole scanning on a port after receiving invalid Modbus packet
• Add scan_type and preserve_old_results parameters to bus-scan/Start RPC request

Scanner utility for extended Wiren Board Modbus protocol

• Fix crash on -h

Wirenboard vendor software set

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Dummy package to provide wb-test-suite required by old build scripts

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Linux kernel, version 5.10.35-wb169, Wiren Board 7

• i2c-wbio: cherry-pick i2c bus recovery logic (mv64xxx driver)
• add CAN SAE J1939 support built-in

Wiren Board Python common library and helpers

• Fix pylint, no functional changes
• MQTT client wrapper: forward all constructor arguments to paho.mqtt.client.Client

Wirenboard network configuration backend for wb-mqtt-confed.

• Fix username, password and PIN gsm settings visibility
• Add unit tests for wb-mqtt-nm-helper
• Fix pylint, no functional changes
• Add GSM pin and mtu configuration
• Do not check connectivity for bridge and tun

Wiren Board modbus devices firmware update and modbus bindings python libraries (python 3)

• reduce modbus retries from 5 to 2
• rework fws downloading & add cache
• add elapsed-time spinner
• Fix help of force flag

Firmware update tool for Wiren Board Modbus devices (WB-M*)

• Add --get-device-info arg

Default system rules for Wiren Board

• power-class-battery: add control title translations

Wiren Board MQTT to SNMP gateway

• Cleanup topics on service stop
• Add -profile flag to enable profiling with pprof
• Schema: add missed units, disable Edit JSON
• Fix template file regex

Wiren Board Smart Home MQTT generic sysfs GPIO driver compatible with HomA conventions

• Fix restoration of outputs state after unexpected controller restart
• gpio_counter: fall "current" as in wb modbus devices
• Add missed wb-utils dependency, no functional changes
• Fix bug when missing WBIO modules are configured in the config
• Rewrite some internals to speed things up, no functional changes
• Change name of wattmeter to electric energy meter.

Telegraf built for WB Cloud agent

• built with limited tags set

Wiren Board MQTT to KNX gateway

• Use unix socket to connect to knxd by default

Wirenboard network configuration python3 library

• Fix username, password and PIN gsm settings visibility
• Add unit tests for wb-mqtt-nm-helper
• Fix pylint, no functional changes
• Add GSM pin and mtu configuration
• Do not check connectivity for bridge and tun

Wiren Board Web UI web interface

• Fix adding devices connected via Modbus over TCP gateways to wb-mqtt-serial configuration
• Fix WB-MRWM2 config page
• Fix device copying between ports
• Fix slow scanning cancel
• Fix firefox error whitescreen error
• Hide vulnerability warning if the problem is fixed
• Fix address assignment in wb-mqtt-serial config
• Add Hz and rpm units translations
• Add missed units translations
• Fix address assignment in wb-mqtt-serial config
• Clear rule editor history on init
• Copy device configurations between ports
• Remove direct websocket port usage in favor of built-in nginx proxy, remove host+port settings
• Show configured devices during fast modbus scan
• Remove empty line after svg dashboard
• Find disconnected wb-mqtt-serial devices
• Add configuration of device port parameters when adding it to wb-mqtt-serial config
• Resolve MQTT topic collisions when adding new devices to wb-mqtt-serial config
• Resolve address collisions when adding new devices to wb-mqtt-serial config
• Add exp-check
• Disallow indexing
• Fix displaying of text parameters on dashboards
• Add download configs and download everything buttons under System page
• Fix tooltip of dropdown editor for channels with defined set of values
• Add dropdown editor for channels with defined set of values
• Postinst: replace config with a correct board-one, if config was not edited by user
• Detect, is running via cloud or not; pass "from_cloud" flag
• Fix loading of device templates with defined firmware versions
• Make tables responsive (json-editor updated to 2.5.3-wb11)
• Add delete button for unknown devices in wb-mqtt-serial config editor
• Fix fullscreen mode on text dashboards and history page
• Fix History page infinite loading because of widgets without id
• Fix Widgets page display when there are widgets without id
• Add duplicate MQTT id checking in wb-mqtt-serial config
• Show disconnected devices in wb-mqtt-serial config
• Add duplicate slave id checking in wb-mqtt-serial config
• Preserve history plot height
• Fix WB-LED configuration
• Add separate chunks to decrease bundle weight
• Remove svg.original from configs
• Move selection to next device after deletion on wb-mqtt-serial config page
• Fixes around cloud connection status, no functional changes
• Add warning if multiple device templates match the same scanned device in wb-mqtt-serial config
• Remove useless scrollbars on wb-mqtt-serial config page
• Fix config generation, no functional changes
• Generate configs, no functional changes
• Do not disconnect from controller after receiving malformed data from MQTT
• Add wb8 config
• Integrate device scanning page into wb-mqtt-serial config editor
• Add json editor autocomplete for devices
• Add SVG-dashboard's style and visibility bindings value validation
• Fix SVG dashboard display with poorly written style, reading or visibility rules
• Fix WB-LED and WB-MRGBW-D config editors
• Add multitenancy suppport for wb-cloud-agent UI
• Fix tooltip on alarm control
• Improve wb-mqtt-serial config loading errors handling
• Improve unsaved changes tracking on wb-mqtt-serial config page

Wiren Board MQTT SmartWeb driver.

• Fix default config (add value_timeout_min)
• Add json editor autocomplete for devices

FIT bootlet images, Wiren Board 7 (bootlet)

Wiren Board modbus devices firmware update tool (python 3)

• reduce modbus retries from 5 to 2
• rework fws downloading & add cache
• add elapsed-time spinner
• Fix help of force flag

Wiren Board Smart Home MQTT abstraction layer and utils library

Default common config files for Wiren Board

• add wb-uart udev rules for wb85x
• nginx: check for broken symlinks in /etc/nginx/sites-enabled
• add watchdog service script to check emmc health
• Use mosquitto unix socket for publishing open ports checking results
• nginx: fix proxy_pass for /mqtt
• nginx: fix config warning
• mosquitto: disabled public websocket 18883 port for security reasons
• nginx: enable gzip compression
• web ui backups: limit number of used cores to half of present in system
• port probe: hide banner on cooldown
• fix default wb_security.conf
• add remote probe to check for open ports
• remove debian/source/format file, no functional changes
• add download_configs and download_everything backends
• fwupdate_upload: handle update from cloud ("from_cloud" flag)
• add UART symlinks on WB8
• add Wiren Board 8 support

Wiren Board command-line utils

• wb-usb-otg: is supported on all wirenboard-8xx compatible devices
• wb-gsm: fix modem turning-on & simselect on 6.8 kernel
• wb-watch-update: add is-update-from-cloud check ("+update-from-cloud" flag)
• fix USB device (Debug Network) mode on WB8
• add Wiren Board 8 support

development files for libwbmqtt

Wirenboard software updates and release management tool

• Fix generated wirenboard.list

Wirenboard software updates and release management tool - python3 library

• Fix generated wirenboard.list

Wiren Board base system packages

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

WB MQTT driver for MasterKit MT8057 CO2 sensor

• add arm64 build, no functional changes

Thin layer built on top of paho-mqtt allowing for connections with unix socket brokers

• Enable tests, no functional changes

one-click diagnostic data collector for Wiren Board,

• Hide "No files for wildcard" warnings to debug

Wiren Board database logger

• Add json editor autocomplete for devices
• Fix several unchanged channels saving

Device tree overlays for Wiren Board devices

• add dependency on linux-image-wb8

Wiren Board test-suite dependencies (python3 packages)

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

• u-boot-tools-wb (companion tools for Das U-Boot bootloader) 2:2021.10+wb1.7.1 → 2:2021.10+wb1.7.2
• mqttui (Subscribe to a MQTT Topic or publish something quickly from the terminal) added 0.21.1-1
• u-boot-wb7 (Das U-Boot bootloader for Wiren Board 7 (image)) 2:2021.10+wb1.7.1 → 2:2021.10+wb1.7.2
• zigbee2mqtt (Zigbee to MQTT bridge (package by Wiren Board team)) 1.35.3-wb101 → 1.38.0-wb101

Provides infrastructure for hardware re-configuration via Device Tree overlays

• introduce wb85x board config
• uarts on mod1 & mod2; wbmz actually not supported now (because of wb-ec firmware)
• wbmz5: fix temperature sensor display
• add wb8x support (on 7.4.x board)
• add dependency on linux-image-wb8

Linux kernel, version 5.10.35-wb169, Wiren Board 6

• i2c-wbio: cherry-pick i2c bus recovery logic (mv64xxx driver)
• add CAN SAE J1939 support built-in

Wiren Board URRI receiver (MQTT driver)

• Fix receiver IP address validation

Reference MQTT-RPC implementation

• Fix exception processing

Wiren Board Configuration Editor Backend

• service: use /etc/default/wb-mqtt-confed
• Backup /etc/ntp.conf by moving to /mnt/data

Wiren Board Smart Home MQTT serial protocol driver

• Fix APC NMC2 AP9630 template
• Add template PID-controller Ptex
• Add new template for Veda VF 51
• Add template APC NMC2 AP9630
• WB-MRWM2 template: add support for startup delay, restart delay, voltage control function
• Add g-leakage group
• ONOKOM templates: fix units
• WB-MRM2-MINI template: add min request interval
• WB-MIR_V2 template: add min request interval
• WB-MAI2-CC template: add min request interval
• WB-MAI6 template: remove FW version
• Add min core voltage reg in wb-mir_v2 template
• Add min core voltage reg in wb-mai2-cc template
• Add min core voltage reg in wb-mr2m template
• Add IEC61107 Mode C protocol
• Add LUNA three-phase electricity meter template
• Add min core voltage reg in m1w2 template
• Somfy SDN: add tilting support
• Add new template for Carel muRack after rework
• Add indirect control channels for WB-MSW-v3/v4/v4-lora and WB-MIR-v2
• Add Energomera CE102 template
• Add channels "tariffs" to templates/config-mercury230.json
• WB-MAI6 template: add WB-VDIV and custom voltage divider support
• Add device address setup RPC
• Add new signature in m1w2 template
• Add GitHub pull request template. No functional changes
• Watch device template changes in /usr/lib/wb-mqtt-serial/templates
• Delete template for Carel muRack
• Add new template for Carel muRack
• Add device setup RPC
• Somfy SDN: speed adjustment is only available on DC motors
• Fix WB-MAI6 configuration interface
• WB-MDM3 template: add light scenes, switch mode, safety and powerup actions support
• Add new template for A-OK AM-35 motors
• Validation error of config containing duplicated ports
• Show template validation errors in log
• Add missed wb-utils dependency, no functional changes
• Add min_request_interval option to device config. The option defines minimal time between requests to a device
• Add mercury230 protocol description to README.md. No functional changes
• Jinjify WB_MWAC v1 template, add cleaning mode, safe state for alarm, fix debounce range, sporadic for alarm
• Publish error in /devices/+/meta/error on device disconnection
• Install missed wb-mqtt-serial.conf.wb8
• Add default config for wb8
• Fixed a crash caused by receiving a large number of incorrect Modbus packets
• Add more verbose internal errors. No functional changes
• Add temperature sensors poll period register for M1W2
• Add MQTT topic id to config/Load RPC response
• Add device signature to MAP3E, MAP3ET, MAP3EV templates
• Fix MAI11 slave id editor position in wb-mqtt-homeui
• Add device signature to WB-MWAC v.2 template
• Add new template for WB-Domofon
• Add new template for A-OK motors
• WB-M1W2 template: add button reset input counters
• Set correct default template for WB-MRPS6
• Fix SOKOL-M template
• Add protocol information to config loading RPC request

Wiren Board common packages

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Somfy and Dooya devices integration via RF-Blinds stick/wbe-module (from smarttone.ru).

• Fix CPU usage when no serial devices found

development files for testing libwbmqtt-based projects

Micron eMMC utility

• Fix changelog, no functional changes

development files for libwbmqtt

• Add missed control types (pressure, lux, sound_level)
• Add escaping for non Latin1 symbols in JSON

Wiren Board Rule Engine

• Fix parseInt() explicit radix 16 handling for leading zero
• Fix meta json unmarshaling, update wbgo.so library
• Alarms schema: disable Edit JSON
• update wbgo.so library: fix go.sum
• Fix stuck on reboot/stop, when multiple virtual devices update their meta
• update wbgo.so library
• bump PahoMQTT dep: v1.4.1 -> v1.4.2
• Fix control meta handling, update wbgo.so library
• Add missed control types, update wbgo.so library
• Add json editor autocomplete for devices

FIT bootlet images, Wiren Board 6 (bootlet)

Wiren Board Cloud agent

• Handle TimeoutExpired exception during events polling
• Tweak curl params
• Fix preinst hook
• fix cloud connection status absense in UI if no providers configured
• Fix config search path
• Substitute mqtt broker url in telegraf config
• Move device certs check to ExecStartPre (instead of postinst)
• Backup config via wb-configs
• Send diagnostics to the cloud backend by request
• Fix service unit
• Add BROKER_URL config option and --broker launch argument for mqtt broker
• Fixes around cloud connection status
• Send agent version to the cloud backend
• Bugfix with cloud url in config
• Add multi-provider support

CLI for wb-mqtt-db

• Fix connection error handling

Wiren Board MQTT Driver for Welrok thermostat

wb-rules-based IIO DAC driver for WB MQTT

• Fix iio-device-num parsing

development files for testing libwbmqtt-based projects

• Add missed control types (pressure, lux, sound_level)
• Add escaping for non Latin1 symbols in JSON

Wiren Board MQTT to Modbus gateway

• Add option to prevent config regeneration
• Fix holding registers detection

knxd configurator for Wiren Board

• schema: fix Global.Error/Global.Trace format
• schema: remove Edit JSON buttons

Wiren Board Smart Home MQTT abstraction layer and utils library

• Add missed control types (pressure, lux, sound_level)
• Add escaping for non Latin1 symbols in JSON

Linux support headers for userspace development

• i2c-wbio: cherry-pick i2c bus recovery logic (mv64xxx driver)
• add CAN SAE J1939 support built-in

Wiren Board Smart Home MQTT generic 1-Wire (w1) driver compatible with HomA conventions

• Fix tests, no functional changes

Wirenboard essential packages

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Wiren Board modbus devices manager (python3 service; backend)

• Stop slow scan faster
• Add port path parameter to bus-scan/Start RPC request
• Do not stop the whole scanning on a port after receiving invalid Modbus packet
• Add scan_type and preserve_old_results parameters to bus-scan/Start RPC request

Scanner utility for extended Wiren Board Modbus protocol

• Fix crash on -h

Wirenboard vendor software set

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Dummy package to provide wb-test-suite required by old build scripts

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

Linux kernel headers for 5.10.35-wb169 on armhf

• i2c-wbio: cherry-pick i2c bus recovery logic (mv64xxx driver)
• add CAN SAE J1939 support built-in

Wiren Board Python common library and helpers

• Fix pylint, no functional changes
• MQTT client wrapper: forward all constructor arguments to paho.mqtt.client.Client

Wirenboard network configuration backend for wb-mqtt-confed.

• Fix username, password and PIN gsm settings visibility
• Add unit tests for wb-mqtt-nm-helper
• Fix pylint, no functional changes
• Add GSM pin and mtu configuration
• Do not check connectivity for bridge and tun

Wiren Board modbus devices firmware update and modbus bindings python libraries (python 3)

• reduce modbus retries from 5 to 2
• rework fws downloading & add cache
• add elapsed-time spinner
• Fix help of force flag

Firmware update tool for Wiren Board Modbus devices (WB-M*)

• Add --get-device-info arg

Default system rules for Wiren Board

• power-class-battery: add control title translations

Wiren Board MQTT to SNMP gateway

• Cleanup topics on service stop
• Add -profile flag to enable profiling with pprof
• Schema: add missed units, disable Edit JSON
• Fix template file regex

Wiren Board Smart Home MQTT generic sysfs GPIO driver compatible with HomA conventions

• Fix restoration of outputs state after unexpected controller restart
• gpio_counter: fall "current" as in wb modbus devices
• Add missed wb-utils dependency, no functional changes
• Fix bug when missing WBIO modules are configured in the config
• Rewrite some internals to speed things up, no functional changes
• Change name of wattmeter to electric energy meter.

Telegraf built for WB Cloud agent

• built with limited tags set

Wiren Board MQTT to KNX gateway

• Use unix socket to connect to knxd by default

Wirenboard network configuration python3 library

• Fix username, password and PIN gsm settings visibility
• Add unit tests for wb-mqtt-nm-helper
• Fix pylint, no functional changes
• Add GSM pin and mtu configuration
• Do not check connectivity for bridge and tun

Wiren Board Web UI web interface

• Fix adding devices connected via Modbus over TCP gateways to wb-mqtt-serial configuration
• Fix WB-MRWM2 config page
• Fix device copying between ports
• Fix slow scanning cancel
• Fix firefox error whitescreen error
• Hide vulnerability warning if the problem is fixed
• Fix address assignment in wb-mqtt-serial config
• Add Hz and rpm units translations
• Add missed units translations
• Fix address assignment in wb-mqtt-serial config
• Clear rule editor history on init
• Copy device configurations between ports
• Remove direct websocket port usage in favor of built-in nginx proxy, remove host+port settings
• Show configured devices during fast modbus scan
• Remove empty line after svg dashboard
• Find disconnected wb-mqtt-serial devices
• Add configuration of device port parameters when adding it to wb-mqtt-serial config
• Resolve MQTT topic collisions when adding new devices to wb-mqtt-serial config
• Resolve address collisions when adding new devices to wb-mqtt-serial config
• Add exp-check
• Disallow indexing
• Fix displaying of text parameters on dashboards
• Add download configs and download everything buttons under System page
• Fix tooltip of dropdown editor for channels with defined set of values
• Add dropdown editor for channels with defined set of values
• Postinst: replace config with a correct board-one, if config was not edited by user
• Detect, is running via cloud or not; pass "from_cloud" flag
• Fix loading of device templates with defined firmware versions
• Make tables responsive (json-editor updated to 2.5.3-wb11)
• Add delete button for unknown devices in wb-mqtt-serial config editor
• Fix fullscreen mode on text dashboards and history page
• Fix History page infinite loading because of widgets without id
• Fix Widgets page display when there are widgets without id
• Add duplicate MQTT id checking in wb-mqtt-serial config
• Show disconnected devices in wb-mqtt-serial config
• Add duplicate slave id checking in wb-mqtt-serial config
• Preserve history plot height
• Fix WB-LED configuration
• Add separate chunks to decrease bundle weight
• Remove svg.original from configs
• Move selection to next device after deletion on wb-mqtt-serial config page
• Fixes around cloud connection status, no functional changes
• Add warning if multiple device templates match the same scanned device in wb-mqtt-serial config
• Remove useless scrollbars on wb-mqtt-serial config page
• Fix config generation, no functional changes
• Generate configs, no functional changes
• Do not disconnect from controller after receiving malformed data from MQTT
• Add wb8 config
• Integrate device scanning page into wb-mqtt-serial config editor
• Add json editor autocomplete for devices
• Add SVG-dashboard's style and visibility bindings value validation
• Fix SVG dashboard display with poorly written style, reading or visibility rules
• Fix WB-LED and WB-MRGBW-D config editors
• Add multitenancy suppport for wb-cloud-agent UI
• Fix tooltip on alarm control
• Improve wb-mqtt-serial config loading errors handling
• Improve unsaved changes tracking on wb-mqtt-serial config page

Wiren Board MQTT SmartWeb driver.

• Fix default config (add value_timeout_min)
• Add json editor autocomplete for devices

Wiren Board modbus devices firmware update tool (python 3)

• reduce modbus retries from 5 to 2
• rework fws downloading & add cache
• add elapsed-time spinner
• Fix help of force flag

Wiren Board Smart Home MQTT abstraction layer and utils library

Default common config files for Wiren Board

• add wb-uart udev rules for wb85x
• nginx: check for broken symlinks in /etc/nginx/sites-enabled
• add watchdog service script to check emmc health
• Use mosquitto unix socket for publishing open ports checking results
• nginx: fix proxy_pass for /mqtt
• nginx: fix config warning
• mosquitto: disabled public websocket 18883 port for security reasons
• nginx: enable gzip compression
• web ui backups: limit number of used cores to half of present in system
• port probe: hide banner on cooldown
• fix default wb_security.conf
• add remote probe to check for open ports
• remove debian/source/format file, no functional changes
• add download_configs and download_everything backends
• fwupdate_upload: handle update from cloud ("from_cloud" flag)
• add UART symlinks on WB8
• add Wiren Board 8 support

Wiren Board command-line utils

• wb-usb-otg: is supported on all wirenboard-8xx compatible devices
• wb-gsm: fix modem turning-on & simselect on 6.8 kernel
• wb-watch-update: add is-update-from-cloud check ("+update-from-cloud" flag)
• fix USB device (Debug Network) mode on WB8
• add Wiren Board 8 support

development files for libwbmqtt

Wirenboard software updates and release management tool

• Fix generated wirenboard.list

Wirenboard software updates and release management tool - python3 library

• Fix generated wirenboard.list

Wiren Board base system packages

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

WB MQTT driver for MasterKit MT8057 CO2 sensor

• add arm64 build, no functional changes

Thin layer built on top of paho-mqtt allowing for connections with unix socket brokers

• Enable tests, no functional changes

one-click diagnostic data collector for Wiren Board,

• Hide "No files for wildcard" warnings to debug

Wiren Board database logger

• Add json editor autocomplete for devices
• Fix several unchanged channels saving

Device tree overlays for Wiren Board devices

• add dependency on linux-image-wb8

Wiren Board test-suite dependencies (python3 packages)

• Add task-wirenboard-wb8
• Add wb-cloud-agent to wb-suite

• u-boot-tools-wb (companion tools for Das U-Boot bootloader) 2:2021.10+wb1.7.1 → 2:2021.10+wb1.7.2
• mqttui (Subscribe to a MQTT Topic or publish something quickly from the terminal) added 0.21.1-1
• u-boot-wb6 (Das U-Boot bootloader for Wiren Board 6 (image)) 2:2021.10+wb1.7.1 → 2:2021.10+wb1.7.2
• zigbee2mqtt (Zigbee to MQTT bridge (package by Wiren Board team)) 1.35.3-wb101 → 1.38.0-wb101