История
1 июля 2019
Новая страница: «500px|EST Interface»
−7
Новая страница: «When working with ETS, it's '''Important''': in “interfaces” ETS, it's necessary to choose the interface of the PC through which communication occurs. Reques…»
−162
Новая страница: «Script for [https://contactless.ru/wiki/index.php/%D0%94%D0%B2%D0%B8%D0%B6%D0%BE%D0%BA_%D0%BF%D1%80%D0%B0%D0%B2%D0%B8%D0%BB_wb-rules wb-rules] упрощающи…»
−9
Новая страница: «Learn more about working with KNX data:[https://contactless.ru/wiki/index.php/MQTT_KNX_Bridge wb-mqtt-knx (MQTT KNX Bridge)]»
−19
Новая страница: «-m "g:0/0/1 GroupValueWrite 0x01" - message for a KNX device»
−26
Новая страница: «-t /devices/knx/controls/data/on - MQTT topic for uploading information»
−24
Новая страница: «-p 1883 - MQTT port»
−4
Новая страница: «-h 192.168.0.10 - IP-address of the controller with KNX»
−6
Новая страница: «Where:»
−1
Новая страница: «An example of a command:»
−4
Новая страница: «To control KNX devices you need to send commands to MQTT topic '''/devices/knx/controls/data/on'''.»
−71
Нет описания правки
−2
Новая страница: «When you receive a message from the KNX device, the data is published to the MQTT topic '''/devices/knx/controls/data''' in Wiren Board 6.»
−41
Новая страница: «All logs are stored in the file '''/var/log/knxd.log'''»
−15
Новая страница: «To check the status: '''service knxd status'''»
−19
Новая страница: «Restart if necessary: '''service knxd restart'''»
−37
Новая страница: «To start KNX daemon, you need to write a line in the console: '''service knxd start'''»
−44
Новая страница: «== Operation ==»
−3
Новая страница: «More detailed:»
−5
Новая страница: «Decrypting keys: {| class="wikitable" !Key !Function |- | -d /var/log/knxd.log | to go into the background and write to a log. |- | -e 1.1.255 |assigns KNX-addres…»
−419
Новая страница: «with:»
−1
Нет описания правки
−6
Новая страница: «DAEMON_ARGS="-u /tmp/eib -u /var/run/knx -i -b ip:" with:»
+6
Новая страница: «Replace the line:»
−13
Новая страница: «After installation, you must edit the file '''/etc/default/knxd''':»
−51
Новая страница: «Go to the console and install the packages [https://contactless.ru/wiki/index.php/MQTT_KNX_Bridge wb-mqtt-knx (MQTT KNX Bridge)], knxd, knxd-tools:»
−58
Новая страница: «300px|Configuration»
−27
Новая страница: «== Configuration== You need to set the module type in the web interface, section'''Configs => Hardware Modules Configuration''': for Internal slot 1 (MOD1) or for…»
−127
Новая страница: «300px| KNX connector»
−23
Новая страница: «When ordering the expansion module together with the controller are installed other terminals (pictured). {| class="wikitable" !Terminal !Function |- |O1 (Red) |K…»
−85
Новая страница: «thumb|300px| KNX extension module»
−16
Новая страница: «== Pinout ==»
−14
Новая страница: «WBE-I-KNX extension module»
+5095