Получение точного времени через GPS/Glonass/en: различия между версиями
(Новая страница: «stratum=0, refid=GPSP, flags=1 Then configure NTP as we need to and so on.») |
(Новая страница: «what to do to get a correct NTP ( ~1 Hour)») |
||
(не показано 9 промежуточных версий этого же участника) | |||
Строка 5: | Строка 5: | ||
what to do to get a correct NTP ( ~1 Hour) | what to do to get a correct NTP ( ~1 Hour) | ||
Поставить libcap-dev – без него не будет работать нтп с настройками кот по умолчанию в системе и после ребута все сломается и придется через дебаг консоль убирать из загрузки нтп. | |||
Через apt-get не получилось – ставил через dpkg брал тут: https://packages.debian.org/wheezy/armel/libcap-dev/download | |||
Качаем отсюда нпт http://www.ntp.org/downloads.html (Production 4.2.8p6) | |||
tar zxvf ntp-4.2.8p6.tar.gz | tar zxvf ntp-4.2.8p6.tar.gz | ||
cd ntp-4.2.8p6 | cd ntp-4.2.8p6 | ||
./configure —enable-linuxcaps # | ./configure —enable-linuxcaps # для этого и нужен libcap-dev | ||
make | make | ||
make install | make install | ||
service ntp stop | service ntp stop | ||
cp /usr/local/bin/ntp* /usr/bin/ && sudo cp /usr/local/sbin/ntp* /usr/sbin/ # | cp /usr/local/bin/ntp* /usr/bin/ && sudo cp /usr/local/sbin/ntp* /usr/sbin/ #заменяем системный нтп новым улучшенным | ||
Далее настраиваем нтп – надо создать алиалсы для драйвера 20 (https://www.eecis.udel.edu/~mills/ntp/html/drivers/driver20.html) | |||
vi /etc/udev/rules.d/10-gps.rules | vi /etc/udev/rules.d/10-gps.rules | ||
Строка 26: | Строка 26: | ||
Можно еще использовать драйвер 22 – нтп + драйвер 20 (нмеа) или 28 (гпсд) | |||
Но 20 и так умеет ппс (flag1 1) и экспериментально я остановился на нем. (https://www.eecis.udel.edu/~mills/ntp/html/refclock.html) | |||
Правим /etc/ntp.conf | |||
server 127.127.20.0 mode 17 minpoll 4 maxpoll 4 iburst prefer | server 127.127.20.0 mode 17 minpoll 4 maxpoll 4 iburst prefer | ||
Строка 35: | Строка 35: | ||
fudge 127.127.20.0 flag1 1 flag2 0 time2 1.0 refid GPSP | fudge 127.127.20.0 flag1 1 flag2 0 time2 1.0 refid GPSP | ||
time2 1.0 | time2 1.0 - это смещение времени гпс от ппс тк гпс и ппс асинхронны и если нет смещения то нтп отбранкует драйвер 20 – подбирается экспериментально по методике ниже (но думаю что для всех виренбордов 5 будет 1.0 (для пи2 у меня получилось 0.7)) https://support.ntp.org/bin/view/Support/ConfiguringNMEARefclocks | ||
if you want a good estimation for fudge time2 (perhaps because PPS is not an option for you) you could use the following procedure: | if you want a good estimation for fudge time2 (perhaps because PPS is not an option for you) you could use the following procedure: | ||
Строка 46: | Строка 46: | ||
Перезагружаемся и смотрим что есть наши алиасы | |||
root@wirenboard:~# ls /dev/gps* | root@wirenboard:~# ls /dev/gps* | ||
/dev/gps0 /dev/gpspps0 | /dev/gps0 /dev/gpspps0 | ||
Далее ждем минут 10 и ntpq -nc peer -c as -c rl | |||
Буква о у 127.127.20.0 – значит что последняя синхронизации с ппс (http://citrin.ru/net:ntpq) | |||
root@wirenboard:~# ntpq -nc peer -c as -c rl | root@wirenboard:~# ntpq -nc peer -c as -c rl | ||
Строка 103: | Строка 102: | ||
clk_jitter=0.008, clk_wander=0.000 | clk_jitter=0.008, clk_wander=0.000 | ||
Это чтобы посмотреть ошибки и что выдает гпс | |||
root@wirenboard:~# ntpq -c clockvar | root@wirenboard:~# ntpq -c clockvar | ||
Строка 118: | Строка 117: | ||
Дальше настраиваем нтп как нам надо – кому что можно откуда и так далее. |
Версия 14:54, 3 июля 2019
The article is advisory in nature and is not intended for ultimate users.
what to do to get a correct NTP ( ~1 Hour)
Поставить libcap-dev – без него не будет работать нтп с настройками кот по умолчанию в системе и после ребута все сломается и придется через дебаг консоль убирать из загрузки нтп. Через apt-get не получилось – ставил через dpkg брал тут: https://packages.debian.org/wheezy/armel/libcap-dev/download Качаем отсюда нпт http://www.ntp.org/downloads.html (Production 4.2.8p6) tar zxvf ntp-4.2.8p6.tar.gz cd ntp-4.2.8p6 ./configure —enable-linuxcaps # для этого и нужен libcap-dev make make install service ntp stop cp /usr/local/bin/ntp* /usr/bin/ && sudo cp /usr/local/sbin/ntp* /usr/sbin/ #заменяем системный нтп новым улучшенным
Далее настраиваем нтп – надо создать алиалсы для драйвера 20 (https://www.eecis.udel.edu/~mills/ntp/html/drivers/driver20.html)
vi /etc/udev/rules.d/10-gps.rules
KERNEL=="ttyAPP2",NAME="%k",SYMLINK+="gps0",MODE="0660",GROUP="ntp"
KERNEL==“pps0",NAME="%k",SYMLINK+="gpspps0",MODE="0660",GROUP="ntp"
Можно еще использовать драйвер 22 – нтп + драйвер 20 (нмеа) или 28 (гпсд)
Но 20 и так умеет ппс (flag1 1) и экспериментально я остановился на нем. (https://www.eecis.udel.edu/~mills/ntp/html/refclock.html)
Правим /etc/ntp.conf
server 127.127.20.0 mode 17 minpoll 4 maxpoll 4 iburst prefer
fudge 127.127.20.0 flag1 1 flag2 0 time2 1.0 refid GPSP
time2 1.0 - это смещение времени гпс от ппс тк гпс и ппс асинхронны и если нет смещения то нтп отбранкует драйвер 20 – подбирается экспериментально по методике ниже (но думаю что для всех виренбордов 5 будет 1.0 (для пи2 у меня получилось 0.7)) https://support.ntp.org/bin/view/Support/ConfiguringNMEARefclocks
if you want a good estimation for fudge time2 (perhaps because PPS is not an option for you) you could use the following procedure:
Switch off the PPS processing for the NMEA driver and mark the clock as noselect. Set the fudge time2 to zero. Add a few good public time servers or another clock; here in Germany I can use my DCF77 radio clock for that purpose. Disable all output sentences of the GPS18x LVC but the GPRMC sentence. Restart the daemon and watch the offset for the NMEA clock. When the value gets stable, use the absolute value of the offset as fudge time2 for the NMEA driver. Optionally restart ntpd and verify that the offset remains small. Note the jitter, which is probably in the order of 5-10msec. If the offset is small enough (better than 2ms is doable, but takes a long time to stabilise), go to the next step. Otherwise fine-tune fudge time2 and repeat this step. Enable PPS processing again if you can. After restarting ntpd jitter and offset should decrease rather fast. Finally, remove the noselect statement and enjoy your fast-locking NMEA clock with a Garmin GPS18x LVC!
Перезагружаемся и смотрим что есть наши алиасы
root@wirenboard:~# ls /dev/gps*
/dev/gps0 /dev/gpspps0
Далее ждем минут 10 и ntpq -nc peer -c as -c rl Буква о у 127.127.20.0 – значит что последняя синхронизации с ппс (http://citrin.ru/net:ntpq)
root@wirenboard:~# ntpq -nc peer -c as -c rl
remote refid st t when poll reach delay offset jitter
==================================================================
o127.127.20.0 .GPSP. 0 l 8 16 377 0.000 0.000 0.008
- 185.22.60.71 212.20.50.208 2 u 21 64 377 3.510 -0.048 0.132
+95.104.192.10 194.190.168.1 2 u 55 64 377 18.911 -1.880 0.093
-144.76.115.197 131.188.3.221 2 u 4 64 377 51.630 -6.302 0.509
+89.111.54.85 194.29.130.252 2 u 46 64 377 25.978 0.225 0.088
ind assid status conf reach auth condition last_event cnt
===============================================
1 30454 974a yes yes none pps.peer sys_peer 4
2 30455 963a yes yes none sys.peer sys_peer 3
3 30456 9424 yes yes none candidate reachable 2
4 30457 933d yes yes none outlier 3
5 30458 943a yes yes none candidate sys_peer 3
associd=0 status=0415 leap_none, sync_uhf_radio, 1 event, clock_sync,
version="ntpd 4.2.8p6@1.3265 Wed Apr 6 16:13:39 UTC 2016 (2)",
processor="armv5tejl", system="Linux/4.1.15-imxv5-x0.1", leap=00,
stratum=1, precision=-17, rootdelay=0.000, rootdisp=1.120, refid=GPSP,
reftime=dab9e00e.9c7d01b8 Thu, Apr 14 2016 9:23:26.611,
clock=dab9e016.a2b1d422 Thu, Apr 14 2016 9:23:34.635, peer=30454, tc=4,
mintc=3, offset=0.000121, frequency=91.858, sys_jitter=0.007629,
clk_jitter=0.008, clk_wander=0.000
Это чтобы посмотреть ошибки и что выдает гпс
root@wirenboard:~# ntpq -c clockvar
associd=0 status=0011 1 event, clk_no_reply,
device="NMEA GPS Clock",
timecode="$GNRMC,092359.000,A,5549.0526,N,03735.1798,E,0.00,172.16,140416,,,A*78",
poll=3426, noreply=1, badformat=0, baddata=0, fudgetime2=1000.000,
stratum=0, refid=GPSP, flags=1
Дальше настраиваем нтп как нам надо – кому что можно откуда и так далее.