2482
правки
WB-MSx Consumer IR Manual/en: различия между версиями
Нет описания правки
Admin (обсуждение | вклад) |
|||
| (не показаны 2 промежуточные версии 1 участника) | |||
| Строка 28: | Строка 28: | ||
'''Warning!''' Numbers used Modbus registers have changed since firmware version '''3.2.0'''. The instructions stated the new numbers of registers. If you are using a device with older firmware, the general principle remains the same, but the numbers of the registers are shifted; as it is — see the [[#Map registers, flags, and inputs (Inputs and Coils)|Map registers, flags, and inputs (Coils and Inputs)]]. A full description of IR device registers can be found in this article under [[#Register map|Register map]]. | '''Warning!''' Numbers used Modbus registers have changed since firmware version '''3.2.0'''. The instructions stated the new numbers of registers. If you are using a device with older firmware, the general principle remains the same, but the numbers of the registers are shifted; as it is — see the [[#Map registers, flags, and inputs (Inputs and Coils)|Map registers, flags, and inputs (Coils and Inputs)]]. A full description of IR device registers can be found in this article under [[#Register map|Register map]]. | ||
At the physical level, the module is connected via [[RS-485/en| RS-485]] interface. Modbus RTU Protocol is used to control the devices. In Wiren Board devices, Modbus data is transmitted over RS-485 communication lines. See the [[Протокол Modbus/en|Modbus Protocol]] page for details. Modbus-address of the device is set at the factory and marked on the label. The address can be changed programmatically | At the physical level, the module is connected via [[RS-485/en| RS-485]] interface. Modbus RTU Protocol is used to control the devices. In Wiren Board devices, Modbus data is transmitted over RS-485 communication lines. See the [[Протокол Modbus/en|Modbus Protocol]] page for details. Modbus-address of the device is set at the factory and marked on the label. The address can be changed programmatically. | ||
In devices with firmware version "'3.1.0"' and later it is also possible to change the settings of data exchange parameters — see [[#Register map|Modbus register map]]. | In devices with firmware version "'3.1.0"' and later it is also possible to change the settings of data exchange parameters — see [[#Register map|Modbus register map]]. | ||
| Строка 68: | Строка 68: | ||
=== Recording the signal to the RAM from the remote control === | === Recording the signal to the RAM from the remote control === | ||
To write a signal (only one) from the remote control to the RAM without putting it in the ROM - write 1 in the flag register at <code>5001</code>. Further actions occur in the same way as described above to record the signal in ROM. After the recording is stopped in the storage registers at <code>2000</code>, the signal will be stored as a sequence of numbers. You can edit this sequence as described above. Note: the contents of these storage registers are not stored when the device is powered off! | To write a signal (only one) from the remote control to the RAM without putting it in the ROM - write 1 in the flag register at <code>5001</code>. Further actions occur in the same way as described above to record the signal in ROM. After the recording is stopped in the storage registers at <code>2000</code>, the signal will be stored as a sequence of numbers. You can edit this sequence as described above. Note: the contents of these storage registers are not stored when the device is powered off! | ||
=== Playing a signal from memory === | |||
To play the signal from memory, write 1 to the flag register at <code>5002</code>. The signal recorded in the storage registers starting with <code>2000</code>will be played. In the absence of the marker of the end of the command will return an error. While the signal is playing, the flag register at <code>5002</code> will be set to 1 and then set to 0. While the signal is being played, no other operations with the IR transceiver via Modbus will be available. | To play the signal from memory, write 1 to the flag register at <code>5002</code>. The signal recorded in the storage registers starting with <code>2000</code>will be played. In the absence of the marker of the end of the command will return an error. While the signal is playing, the flag register at <code>5002</code> will be set to 1 and then set to 0. While the signal is being played, no other operations with the IR transceiver via Modbus will be available. | ||