translator, wb_editors
4268
правок
Wiren Board 6.7: Peripherals/en: различия между версиями
Wiren Board 6.7: Peripherals/en (просмотреть исходный код)
Версия 22:43, 28 сентября 2022
, 1 год назадНет описания правки
Matveevrj (обсуждение | вклад) |
Matveevrj (обсуждение | вклад) |
||
| (не показаны 4 промежуточные версии этого же участника) | |||
| Строка 13: | Строка 13: | ||
!Comments | !Comments | ||
|- | |- | ||
| colspan="6" style="text-align:center; vertical-align: middle; "| | | colspan="6" style="text-align:center; vertical-align:middle;" | '''Outputs A1-A4''' | ||
|- | |- | ||
|A1(out) | |A1(out) | ||
| Строка 43: | Строка 43: | ||
| Open collector output; | | Open collector output; | ||
|- | |- | ||
| colspan="6" style="text-align:center; vertical-align: middle; "| | | colspan="6" style="text-align:center; vertical-align:middle;" | '''Outputs A1-A4''' (inverted; those. "1" on gpio appears when there is no voltage at the input) | ||
|- | |- | ||
|A1 (in) | |A1 (in) | ||
| Строка 105: | Строка 105: | ||
|/dev/ttymxc1 | |/dev/ttymxc1 | ||
|/dev/ttyRS485-1 | |/dev/ttyRS485-1 | ||
| Signed | | Signed ''RS-485'', terminal blocks A and B | ||
| Uninsulated port, terminator installed | | Uninsulated port, terminator installed | ||
|- | |- | ||
|/dev/ttymxc3 | |/dev/ttymxc3 | ||
|/dev/ttyRS485-2 | |/dev/ttyRS485-2 | ||
| Signed | | Signed ''RS-485'', terminal blocks A/L and B/H (this port can be used as CAN) | ||
| Uninsulated port, terminator installed, multiplexed with CAN | | Uninsulated port, terminator installed, multiplexed with CAN | ||
|- | |- | ||
| Строка 116: | Строка 116: | ||
|/dev/ttyMOD1 | |/dev/ttyMOD1 | ||
| UART on the extension module MOD1 | | UART on the extension module MOD1 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc4 | |/dev/ttymxc4 | ||
|/dev/ttyMOD2 | |/dev/ttyMOD2 | ||
| UART on the extension module MOD2 | | UART on the extension module MOD2 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc5 | |/dev/ttymxc5 | ||
|/dev/ttyMOD3 | |/dev/ttyMOD3 | ||
| UART on the extension module MOD3 | | UART on the extension module MOD3 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc6 | |/dev/ttymxc6 | ||
|/dev/ttyMOD4 | |/dev/ttyMOD4 | ||
| UART on the extension module MOD4 | | UART on the extension module MOD4 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc7 | |/dev/ttymxc7 | ||
| Строка 153: | Строка 153: | ||
|style="text-align:center; vertical-align:middle;" |'''GPIO number''' | |style="text-align:center; vertical-align:middle;" |'''GPIO number''' | ||
|style="text-align:center; vertical-align:middle;" |'''Pinmux pad name''' | |style="text-align:center; vertical-align:middle;" |'''Pinmux pad name''' | ||
|style="text-align:center; vertical-align:middle;" | | |style="text-align:center; vertical-align:middle;" |'''Pin''' | ||
|style="text-align:center; vertical-align:middle;" |'''Function''' | |style="text-align:center; vertical-align:middle;" |'''Function''' | ||
|- | |- | ||