3690
правок
(Новая страница: «WB-MSW v.4 Modbus Sensor») Метки: правка с мобильного устройства правка из мобильной версии |
(Новая страница: «== Modifications ==») Метки: правка с мобильного устройства правка из мобильной версии |
||
Строка 9: | Строка 9: | ||
| old_page = WB-MSW v.3 Modbus Sensor | | old_page = WB-MSW v.3 Modbus Sensor | ||
}} | }} | ||
[[File:WB-MSW v.4 front.png |300px|thumb|right| Universal sensor WB-MSW v.4, front view]] | |||
[[File:WB-MSW v.4 front.png |300px|thumb|right| | [[File:WB-MSW v.4 side.png|300px|thumb|right| Universal sensor WB-MSW v.4, rear view. You can see a list of possible options and pin assignments on screw connectors]] | ||
[[File:WB-MSW v.4 side.png|300px|thumb|right| | [[File:WB-MSW v.4 PCB.png |300px|thumb|right| WB-MSW board]] | ||
[[File:WB-MSW v.4 PCB.png |300px|thumb|right| | |||
== Destination == | |||
= | |||
{{Wbincludes:WB-MSW v.3 Functions}} | {{Wbincludes:WB-MSW v.3 Functions}} | ||
The module is controlled from a controller or a PC via the RS-485 bus using commands using the Modbus RTU protocol. | |||
== Change from previous version == | |||
= | |||
{{Wbincludes:WB-MSW v.4 Difference v.3}} | {{Wbincludes:WB-MSW v.4 Difference v.3}} | ||
== Modifications == | |||
= | |||
The sensor can be supplied in any combination of built-in sensors that it is equipped with at the factory, they cannot be purchased separately. | |||
'''Attention!''' LED indicators, light sensor and IR LEDs are physically on the same board, so they are present or absent only at the same time. | |||
''' | |||
== Body painting == | |||
= | |||
{{Wbincludes: WB-MSW v.3 Body Painting}} | {{Wbincludes: WB-MSW v.3 Body Painting}} | ||
== Specifications == | |||
= | |||
{{Wbincludes:WB-MSW v.4 TechSpec Measured Values}} | {{Wbincludes:WB-MSW v.4 TechSpec Measured Values}} | ||
{| class="wikitable" | {| class="wikitable" | ||
! style="text-align: center;" | | ! style="text-align: center;" | Parameter | ||
! style="text-align: center;" | | ! style="text-align: center;" | Value | ||
|- | |- | ||
{{Wbincludes:WB-MSW v.4 Tech Table (Power, IR and indication)}} | {{Wbincludes:WB-MSW v.4 Tech Table (Power, IR and indication)}} | ||
Строка 70: | Строка 50: | ||
{{Wbincludes:WB-MSW v.4 Operating conditions CO2}} | {{Wbincludes:WB-MSW v.4 Operating conditions CO2}} | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |Dimensions | ||
|- | |- | ||
| | | Dimensions | ||
| 80 x 80 x 23.6 | | 80 x 80 x 23.6 mm (with lens) | ||
{{Wbincludes:Weight}} | {{Wbincludes:Weight}} | ||
80 g | |||
80 | |||
|} | |} | ||
== General principle of operation == | |||
= | |||
=== TH sensor === | |||
{{Wbincludes:WB-MSW v.4 TH}} | {{Wbincludes:WB-MSW v.4 TH}} | ||
=== Motion sensor === | |||
=== | |||
Строка 104: | Строка 74: | ||
=== LED indicators and buzzer === | |||
=== | |||
The LED indicators are located on the same board as the light sensor and the IR transmitter, so if you did not select one of these options, you will not have indicators. The buzzer is located on the board and is available in all configurations. | |||
{{Wbincludes:WB-MSW v.3 LED indicators}} | {{Wbincludes:WB-MSW v.3 LED indicators}} |