WB-MSW v.4 Modbus Sensor/en: различия между версиями

<languages/>

{{PDF}}

{{NewVersion

| old_name = WB-MSW v.3

| old_page = WB-MSW v.3 Modbus Sensor

}}

[[File:WB-MSW v.4 front.png |300px|thumb|right| Universal sensor WB-MSW v.4, front view]]

[[File:WB-MSW v.4 side.png|300px|thumb|right| Universal sensor WB-MSW v.4, rear view. You can see a list of possible options and pin assignments on screw connectors]]

== Destination ==

{{Wbincludes:WB-MSW v.3 Functions}}

The module is controlled from a controller or a PC via the RS-485 bus using commands using the Modbus RTU protocol.

== Change from previous version ==

{{Wbincludes:WB-MSW v.4 Difference v.3}}

== Body painting ==

{{Wbincludes: WB-MSW v.3 Body Painting}}

== Specifications ==

{{Wbincludes:WB-MSW v.4 TechSpec Measured Values}}

{| class="wikitable"

! style="text-align: center;" | Value

|-

{{Wbincludes:WB-MSW v.4 Tech Table (Power, IR and indication)}}

{{Wbincludes:Control}}

{{Wbincludes:WB-MSW v.4 Operating conditions CO2}}

|-

! colspan="2" |Dimensions

| Dimensions

| 80 x 80 x 23.6 mm (with lens)

|}

=== TH sensor ===

{{Wbincludes:WB-MSW v.4 TH}}

    

{{Wbincludes:WB-MSW v.3 Motion Sensor}}

The LED indicators are located on the same board as the light sensor and the IR transmitter, so if you did not select one of these options, you will not have indicators. The buzzer is located on the board and is available in all configurations.

{{Wbincludes:WB-MSW v.3 LED indicators}}

Turning on, frequency and duration of LED flashes are set in the web interface or in the corresponding Modbus registers. The frequency and duration are set the same for both LEDs, so when they are turned on at the same time, they will flash synchronously. When turning on the LEDs, make sure that the frequency and duration of the flashes are not 0, otherwise the LEDs will not work.

   

{{Wbincludes:WB-MSW v.3 IR}}

   

{{Wbincludes:WB-MSW v.3 Illumination}}

   

{{Wbincludes:WB-MSW v.3 Nouse}}

   

{{Wbincludes:VOC WB-MSW v.4}}

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

=== CO2 Sensor ===

{{Wbincludes:WB-MSW v.4 CO2}}

[[Special:MyLanguage/Image: WB-MSW v.4 CO2 CM1106 Period.png  |300px|thumb|right| Calibration period in WB-MSW v.4 sensor. ]]

The calibration period can be adjusted in the '''CO₂ sensor calibration period''' parameter. By default, this parameter is not polled, enable its polling in the wb-mqtt-serial driver settings.

====Autocalibration====

{{Wbincludes:WB-MSW v.4 CO2 Autocalibration}}

The period of automatic calibration can be changed in the settings.

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

{{WebUIAddDevice

| template= WB-MSW v.4

}}

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

</gallery>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

{{Modbus Device Firmware Update  

| MS=true  

|changelog=WB-MSW v.4: Changelog}}

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>

|-

|5.2

|08.2023 - ...

|

|-

|5.2

|v5.2B/5R, v5.2B/6  

|08.2023

|

|-

|5.2

|08.2023

|

|-

|5.2

|06.2023 - 07.2023

|

|-

|-

|05.2023 - ...

|

|-

|-

|04.2023 - ...

|

|-

|}

<div lang="ru" dir="ltr" class="mw-content-ltr">

</div>