Все переводы
Введите имя сообщения для показа всех доступных переводов.
Найдено 2 перевода.
Сообщение | Текущий текст |
---|---|
ист. английский (en) | ==The procedure for recovering the root password on the Wiren Board 6 controller== # Connect to the debug port of the [[Wiren Board 6/en| Wiren Board 6]] controller (via microUSB-connector Debug Console). The connection is described in detail on the [[Debug_UART/en|Debug UART]] page. # Turn on the power of the controller (the controller indicator lights green continuously) and when a message "Hit any key to stop autoboot:" appears with the selected countdown in the UART console, then press any key. # In response to the command line prompt <code>=></code> sequentially enter the command:<br/><code>setenv optargs ro rootwait fixrtc single init=/bin/sh</code><br/><code>run bootcmd</code><br/> If you do not enter commands, watchdog restarts the controller. # After downloading (the indicator of the controller lights up red continuously), we obtain a system prompt <code>#</code> # Mount the root filesystem<br/><code>mount -n -o remount,rw /dev/mmcblk0p2 /</code><br/> and we get the message <code> EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)</code> #Mount the partition from the configuration backup:<br/><code>mount /dev/mmcblk0p6 /mnt/data</code><br/>and we get the message <code>EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)</code> #Enter <code>passwd</code> and change password. Successful password change: <code>passwd: password updated successfully</code> # Copy the new password to the section from the configuration backup:<br/><code>cp /etc/shadow /mnt/data/etc</code> # Unmount both file systems:<br/><code> # sync</code><br/><code> # umount /mnt/data</code><br/><code> # umount /</code> # Turn off and turn on the power again. The password is changed. |
ист. русский (ru) | ==Процедура восстановления пароля пользователя root на Wiren Board 6== # Подключаемся к отладочному порту контроллера [[Wiren_Board_6|Wiren Board 6]] (microUSB-разъем Debug Console). Подробно подключение описано на странице [[Debug_UART|Debug UART]]. # Включаем питание контроллера (индикатор контроллера светится зеленым непрерывно) и при появлении сообщения с отбратным отсчетом "Hit any key to stop autoboot:" в UART-консоли нажимаем любую клавишу. # В ответ на приглашение командной строки <code>=></code> последовательно вводим команды:<br/><code>setenv optargs ro rootwait fixrtc single init=/bin/sh</code><br/><code>run bootcmd</code><br/> Если команды не вводить, то watchdog перезагрузит контроллер. # После загрузки (индикатор контроллера светится красным непрерывно) получаем системное приглашение <code>#</code> # Монтируем корневую файловую систему<br/><code>mount -n -o remount,rw /dev/mmcblk0p2 /</code><br/>и получаем сообщение <code> EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)</code> #Монтируем раздел с резервной копии конфигурации:<br/><code>mount /dev/mmcblk0p6 /mnt/data</code><br/>и получаем сообщение <code>EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)</code> #Вводим команду <code>passwd</code> и меняем пароль. Успешное изменение пароля: <code>passwd: password updated successfully</code> #Копируем новый пароль в раздел с резервной копии конфигурации:<br/><code>cp /etc/shadow /mnt/data/etc</code> #Отмонтируем обе файловые системы:<br/><code> # sync</code><br/><code> # umount /mnt/data</code><br/><code> # umount /</code> #Выключаем и снова включаем питание. Пароль изменен. |