Все переводы
Введите имя сообщения для показа всех доступных переводов.
Найдено 2 перевода.
Сообщение | Текущий текст |
---|---|
ист. английский (en) | Configuration process: # Enable access point mode. For this: #* open file <code>/etc/default/hostapd</code> and uncomment the string(e.g.,remove the # at the beginning of the string)<syntaxhighlight lang="bash">DAEMON_CONF="/etc/hostapd.conf"</syntaxhighlight> #* edit the <code>/etc/hostapd.conf</code> file like in the example:<syntaxhighlight lang="bash"> interface=wlan0 #driver=nl80211 # this line should stay commented ssid=WirenBoard # you can substitute WirenBoard with a different name for the hotspot channel=1 wpa=2 wpa_passphrase=your_password # replace your_password with your own password wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP CCMP rsn_pairwise=TKIP CCMP </syntaxhighlight> # Edit <code>/etc/network/interfaces</code>: #* uncomment and edit the lines(or add them, if there were none) related to the hotspot settings: <syntaxhighlight lang="bash"> iface wlan0 inet static address 192.168.42.1 # here 192.168.42.1 - is the address where the Wiren Board controller will be located in the new network; you can specify a different address netmask 255.255.255.0 </syntaxhighlight> #* comment out the lines related to the operating in client mode:<syntaxhighlight lang="bash"> #auto wlan0 #iface wlan0 inet dhcp # wpa-ssid {ssid} # wpa-psk {password} </syntaxhighlight> # Run the command <syntaxhighlight lang="bash"> /etc/init.d/hostapd restart </syntaxhighlight> |
ист. русский (ru) | Процесс настройки: # Включите режим точки доступа. Для этого: #* в файле <code>/etc/default/hostapd</code> раскомментируйте строку (то есть удалите знак '''#''' в начале строки)<syntaxhighlight lang="bash">DAEMON_CONF="/etc/hostapd.conf"</syntaxhighlight> #* отредактируйте файл <code>/etc/hostapd.conf</code>, чтобы он выглядел так:<syntaxhighlight lang="bash"> interface=wlan0 #driver=nl80211 # оставьте эту строку закомментированной ssid=WirenBoard # вместо WirenBoard можете подставить другое имя для создаваемой точки доступа channel=1 wpa=2 wpa_passphrase=your_password # вместо your_password подставьте пароль wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP CCMP rsn_pairwise=TKIP CCMP </syntaxhighlight> # Отредактируйте <code>/etc/network/interfaces</code>: #* раскомментируйте и отредактируйте (или добавьте, если их не было) строки, относящиеся к настройке в режиме точки доступа: <syntaxhighlight lang="bash"> iface wlan0 inet static address 192.168.42.1 # здесь 192.168.42.1 - адрес, по которому в новой сети будет находиться Wiren Board; можете указать другой адрес netmask 255.255.255.0 </syntaxhighlight> #* закомментируйте строки, относящиеся к работе в режиме клиента:<syntaxhighlight lang="bash"> #auto wlan0 #iface wlan0 inet dhcp # wpa-ssid {ssid} # wpa-psk {password} </syntaxhighlight> # Выполните команду <syntaxhighlight lang="bash"> /etc/init.d/hostapd restart </syntaxhighlight> |