История
27 июня 2019
Новая страница: «The wiring on the terminal blocks of Wiren Board devices»
−24
Новая страница: «Connection of peripheral devices»
−50
Новая страница: «Supported devices»
−48
Новая страница: «Devices of our production with the RS-485 interface»
−38
Новая страница: «== Supported Devices ==»
−32
Новая страница: «The valid power range is '''9 — 36 V''' for WB rev.6.1 - 6.4.1 , anda '''9 — 48''' for WB6.5. The average consumption of the Board is 1.5 — 2 watts. But…»
−143
Новая страница: «For backup power, you can connect the internal extension module WBMZ-BATTERY2 with Li-Ion (Li-Pol) battery.'''Important: when the controll…»
−225
Новая страница: «It is possible to simultaneously connect the sources to different inputs, including different voltages.»
−75
Новая страница: «* Power-over-Ethernet (PoE Passive). Read more Power over Ethernet.»
−50
Новая страница: «* VIN and GND terminals: two VIN terminals to which two independent power supplies can be connected for redundancy. The grounds of the power supplies must be conn…»
−123
Новая страница: «* DC jack - standard plug connector (5.5x2.1mm) on the left side of the case.»
−50
Новая страница: «The controller has three external inputs for power connection:»
−53
Новая страница: «== Power Supply ==»
−2
Новая страница: « Hardware watchdog disable»
−53
Новая страница: «The controller contains a separate hardware watchdog that reboots it entirely on power when the software freezes.»
−79
Новая страница: «== Watchdog ==»
−25
Новая страница: «The real-time clock is powered by an internal backup battery.»
−71
Новая страница: « "Buzzer" — beeps, its frequency is adjustable.»
−56
Новая страница: «Отладочный порт/en/ Debug port — by connecting to it, you can directly access the controller console. Through it you can also interact with th…»
−194
Новая страница: «== Ports and interfaces ==»
−13
Новая страница: «'''In versions starting from WB6.4''' detachable screw terminals "series 15EDG" with a pitch of 3.5 mm were applied as interface terminals. When screwing, do not…»
−122
Новая страница: «In the 6.3 revision of Wiren Board controller terminals of "type 250" applied as front-end terminals. These are self-locking clips. When the cleaned single wire i…»
−360
Новая страница: «|- ! colspan="8"| Bottom row, right block |- | '''A1-A4''' || 40V , 1A || High Z || Управление низковольтной нагрузкой/en|Open…»
−353
Новая страница: «| '''O1-O3''' || | ||| || |Inputs/outputs of the 2nd extension module»
−22
Новая страница: «{| border="1" width="700" class="wikitable" style="text-align:center" | '''sign''' | width="20%"| '''Max. V, I''' | width="10%" | '''state''' '''by default'''…»
−166
Новая страница: «Some terminal blocks can be used to perform more than one function. See the detailed description in the Мультиплексирование портов/en|…»
−118
Новая страница: «== Terminal blocks ==»
−3
Новая страница: «Multiple DS18B20 temperature sensors can be connected to each channel via a loop: depending on the loop length, the maximum number of sensors is 10 to 20 (the lim…»
−217
Новая страница: «The mode of each channel is selected independently in the controller configuration. Through the web interface, the desired configuration is located in the section…»
−77
Новая страница: «The W1 and W2 channels can work as an interface for connecting 1-Wire sensors (default) or as digital inputs "dry contact"type. Note t…»
−251
Новая страница: «== W1-W2 channels ==»
−4
Новая страница: «* Discrete input — is triggered when the voltage at the terminal is 5 V»
−55
Новая страница: «* ADCwith a measurement range of 0 — 28 V»
−41
Новая страница: «* open collector output is a key (3A/30V), closing output to the ground»
−48
Новая страница: «Universal channel Ah combines three functions and can work as:»
−74
Новая страница: « thumb | 500px| Wiren Board 6 ports and interfaces thumb|400px|Working with self-locking terminals»
−37
Новая страница: «== Universal inputs/outputs A1-A4 ==»
−26
Новая страница: «It is convenient to use +5V output to power the sensors. It is protected from short circuit and high voltage supply. When the controller is powered by a battery,…»
−225
Новая страница: «''' 1-Wire''' — is a bus for connecting external sensors on two or three wires. Since this is a bus, you can connect multiple devices to the same…»
−153
Новая страница: «''' CAN''' — is the standard of communication over a two-wire bus. The controller is multiplexed (output to the same terminals) with a second RS-485…»
−94
Новая страница: «Basically in Wiren Board, WB-mqtt-serial driver works through the system of MQTT-messages with connected RS-485 devices.»
−47
Новая страница: « Setting up connection of the devices is carried out in the web interface.»
−45
Новая страница: «The article will help you to choose and lay the bus cables correctly.»
−40
Новая страница: «The controller has 2 RS-485 ports + 2 more ports can be added Wiren_Board_6:_Модуль_расширения_RS485-ISO_(WBE2-I-RS485-ISO)/en| by RS-485 extens…»
−36
Новая страница: «'''RS-485''' — two-wire bus communication standard.»
−82
Новая страница: «File:rs-485-setup-configs.png|thumb|right|300 px|Configuration is set through the section ''Configs'' [[RS-485:Настройка через веб-интерф…»
−31
Новая страница: «The controller is equipped with two USB 2.0 (A/F) ports. Both ports operate in USB Host mode; in future versions of the controller, the first port (closest to the…»
−187
Новая страница: «'''Ethernet''' supports speed up to 10/100 Mbit/s. Wiren Board 6 controller is equipped with two such interfaces.»
−91
Нет описания правки
−3
Новая страница: «== Wireless interfaces ==»
−20