translator, wb_editors
4444
правки
(Новая страница: «==Method 3 (without connecting to the controller)==») |
Matveevrj (обсуждение | вклад) |
||
(не показано 10 промежуточных версий 3 участников) | |||
Строка 1: | Строка 1: | ||
<languages/> | <languages/> | ||
[[File:Web ip.png|400px|thumb|IP addresses can be conveniently viewed in the web interface by connecting to the Wi-Fi access point | {{DISPLAYTITLE: How to find the IP address of the Wiren Board controller}} | ||
[[File:Web ip.png|400px|thumb|IP addresses can be conveniently viewed in the web interface by connecting to the access point created by the Wi-Fi controller]] | |||
==Via WiFi== | |||
The controller creates a Wi-Fi hotspot and we can connect to it: | |||
* Open the list of Wi-Fi hotspots on your laptop or phone. | |||
* Select an access point named <code>WirenBoard-XXXXXXXX</code> from the list. Where XXXXXXXX is the serial number of the controller. | |||
When connected via Wi-Fi, the controller will be available at '''[http://192.168.42.1 192.168.42.1]'''. | |||
By default, no password is required to connect to the controller via Wi-Fi, but you can change this. | |||
== IP addresses of the controller== | == IP addresses of the controller== | ||
A controller can have multiple IP addresses because it can connect to networks in | A controller can have multiple IP addresses because it can connect to networks in multiple ways: | ||
*via Ethernet - by default | *via Ethernet - by default, receives an IP address from the router via DHCP, | ||
*via Wi-Fi - by default creates an access point where it has a fixed address ''192.168.42.1'', | *via Wi-Fi - by default creates an access point where it has a fixed address ''192.168.42.1'', | ||
*via GPRS. | *via GPRS. | ||
To log into the controller using the IP address obtained by the controller's Ethernet interface, you must be on the same network to which the controller is connected via Ethernet. | |||
It is almost never possible to access the controller at the address received by the GPRS interface - cellular operators usually issue [https://help.keenetic.com/hc/ru/articles/213965789-%D0%92-%D1%87%D0%B5%D0%BC-%D0%BE%D1%82%D0%BB%D0%B8%D1%87%D0%B8%D0%B5-%D0%B1%D0%B5%D0%BB%D0%BE%D0%B3%D0%BE-%D0%B8-%D1%81%D0%B5%D1%80%D0%BE%D0%B3%D0%BE-IP-%D0%B0%D0%B4%D1%80%D0%B5%D1%81%D0%B0 are "gray" IP addresses] and cannot be accessed from the Internet | |||
==Via debug port== | |||
== | |||
[[File:Ifconfig ip.png|400px|thumb|IP addresses can be viewed by connecting to the console via [[Debug UART|Debug UART]]]] | [[File:Ifconfig ip.png|400px|thumb|IP addresses can be viewed by connecting to the console via [[Debug UART|Debug UART]]]] | ||
Connect to the controller | Connect to the controller via the debug port [[Special:MyLanguage/Debug UART|Debug UART]]. After connecting, enter your login and password (by default ''root'' - ''wirenboard''), then enter the command | ||
<syntaxhighlight lang="bash"> | <syntaxhighlight lang="bash"> | ||
ifconfig | ifconfig | ||
Строка 28: | Строка 35: | ||
The address will be written after the words <code>inet addr:</code>. | The address will be written after the words <code>inet addr:</code>. | ||
==Through a router (not connecting to a controller)== | |||
If you have connected the controller via Ethernet or Wi-Fi to your router, the IP address of the controller can be seen in the web interface of the router. Typically, the menu item name contains the word ''DHCP''. | |||