12 063
правки
(Новая страница: «{| class="wikitable" !Parameter !Value |- |Number of inputs |16 |- |Isolated input groups |2 |- |Input type |dry contact, the opening by the current at») |
(Новая страница: «400px|thumb|none|DI == Device pictures == {{WBPictures|1}}») |
||
(не показано 10 промежуточных версий этого же участника) | |||
Строка 29: | Строка 29: | ||
the opening by the current at | the opening by the current at | ||
earth fault | |||
|- | |- | ||
| | |Operation condition | ||
| | |GND input lockout | ||
|- | |- | ||
| | |Tripping current | ||
|1 | |1 mA | ||
|- | |- | ||
| | |Minimum pulse width to trigger | ||
|10 | |10 MS | ||
|- | |- | ||
| | |Minimum time between consecutive signals | ||
|5 | |5 MS | ||
|- | |- | ||
| | |Voltage "wetting" | ||
|4 | |4.5 V | ||
|- | |- | ||
| | |Module type | ||
|"I" (inverted address scheme) | |"I" (inverted address scheme) | ||
|- | |- | ||
| | |Maximum power consumption | ||
|0 | |0.2 W | ||
|- | |- | ||
| | |Width, DIN units | ||
|3 | |3 | ||
|- | |- | ||
| | |Size | ||
|53,3x90,2x57,5 | |53,3x90,2x57,5 mm | ||
|} | |} | ||
{| class="wikitable" | {| class="wikitable" | ||
!colspan="2" | ''' | !colspan="2" | '''Terminals and wire section''' | ||
|- | |- | ||
|| | || Recommended wire cross-section with TSVI, mm<sup>2</sup>|| 0,75 — 1 | ||
|- | |- | ||
|| | || Length of the standard sleeve NSVE, mm || 8 (10 for adjusting screwless terminal blocks) | ||
|- | |- | ||
|| | || Torque of screws, N∙m || 0,2 (for screw terminals) | ||
|- | |- | ||
|} | |} | ||
[[File:DIN 3U.png |300px|thumb|right| | [[File:DIN 3U.png |300px|thumb|right|Dimensions]] | ||
== | == Connection to controller == | ||
See section [[Модули_ввода-вывода/en#Activating the modules in the controller web interface|activating the module in the web interface of the controller]]. | |||
''' | controls like EXT'''x'''_DR('''1-16''') appear in Discrete I/O device, corresponding to the inputs of the module. Corresponding MQTT topics (read-only) look like: /devices/wb-gpio/controls/EXT'''x'''_DR'''y'''. | ||
== Connectivity == | |||
'''Sensors/counters with pulse outputs/buttons.''' | |||
Such devices form a signal by closing two wires that are suitable for them. Connect one wire to the GND terminal of the module. Connect the second wire to the Dx terminal. A current of less than 2 mA flows through the button. Some counters have a pulse output on the optocoupler, then the two wires have a polarity - "plus" and "minus". In this case, minus is connected to GND, plus to Dx. | |||
'''Devices with open collector output.''' | |||
Both device and controller must be connected to the common grounding bus. Connect the open collector output to the Dx terminal. | |||
The module inputs are galvanically isolated from the controller. Therefore, the ground GND of the module and the controller may be different. | |||
---- | ---- | ||
''' | '''Note that the GND terminals of the upper row are used to connect the devices to inputs 1 to 8, and the GND terminals of the lower row are used for inputs 9 to 16.''' | ||
[[Файл:DI.png| | [[Файл:DI.png|400px|thumb|none|DI]] | ||
== | == Device pictures == | ||
{{Wbincludes:WBPictures|1}} | {{Wbincludes:WBPictures|1}} |
правки