История
26 января 2021
11 июня 2019
Нет описания правки
+6
Нет описания правки
Новая страница: «{| class="wikitable" ! Counter name ! Type in the configuration file |- | Pulsar water meter | pulsar-water |- | Pulsar v1.1 water meter | pulsar-water-v1_1 |- |…»
−151
Новая страница: «=== Select the counter type in the configuration file ===»
−33
Новая страница: «Two types of counters are supported (multi-jet Pulsar-M counter needs to be tested).»
−126
Новая страница: «See RS-485:Настройка через веб-интерфейс/en»
+1
Новая страница: «== Connecting the sensor to the SOFTWARE ==»
−8
Новая страница: «NOTE: when specifying the address of the counter in the Web-interface of the controller, you do not need to specify the leading zeros in the address! That is, if…»
−82
Новая страница: «Example: if the label is 14_12345, the device address is 00012345.»
−54
Новая страница: «Address water meter pulsar is on his body: on the sticker beneath the dial to the right (see photo) caused an entry XX_AAAAA. Here AAAAA - Junior bits of the addr…»
−150
Новая страница: «300px|thumb|right|Pulsar water meter with address marked »
−62
Новая страница: «=== Water meter "Pulsar" ===»
−20
Новая страница: «The device address can be displayed on the display successive presses on the button under the display. At some point, the display will display 8 digits - this is…»
−131
Новая страница: «=== Heat Meter "Pulsar"===»
−23
Новая страница: «'''00 83 60 43''' 0A 12 CB C1 0C 00 00 00 00 00 79 E6 2A 91, the counter address is 00836043.»
−10
Новая страница: «In this case, you should get the answer in the form: <pre> BB BB BB BB 0A XX XX XX XX XX XX XX XX XX XX XX XX XX </pre> where BB BB BB BB is the desired address,…»
−70
Новая страница: «If there is no response, send request <pre> 00 00 00 00 0A 0C 01 00 79 E6 C3 4A </pre>»
−51
Новая страница: «For example, if the device responded with an answer 0F F0 0F F0 01 23 45 67 xx xx, the address of the device is 01234567.»
−36
Новая страница: «where AA AA AA is the address you're looking for, XX doesn't matter.»
−20
Новая страница: «#Via serial-tool, send…»
−69
Новая страница: «#Make sure that only one counter is connected to the interface;»
−45
Новая страница: «The algorithm for obtaining the address of the connected device (must be valid for all pulsar devices connected to RS-485, tested on water meters "pulsar water me…»
−222
Новая страница: «Depending on the software version, different commands are used to determine the address ("network address" in the manufacturer's terminology) of counters connecte…»
−109
Новая страница: «The address of the devices operating under the pulsar Protocol is 8 decimal digits (12 34 56 78). '''When specifying an address in the Web-interface of the contro…»
−86
Новая страница: «== Getting the address ==»
−12
Новая страница: «Important: Incorrect configuration of communication parameters may result in incorrect data from the meter.»
−105
Новая страница: «*Speed: 9600 baud *Parity bit: N *Stop bits: 1»
−37
Новая страница: «=== Serial port settings ===»
−44
Новая страница: «*brown - V+ (9-30 V, power by Wiren Board via Vout) *white - V- (connects to GND) *yellow - RS-485 A *green - RS-485 B»
−102
Новая страница: «Color marking of wires:»
−32
Новая страница: «Connection to the Wiren Board is made via the RS-485/en interface according to the manual to the meter.»
−70
Новая страница: «== Connection ==»
−12
Новая страница: «Connection of the Pulsar meters»
+5577