Disassembling the controller case/en: различия между версиями

Disassembling the controller case/en (просмотреть исходный код)

Версия 09:05, 19 августа 2022

739 байт добавлено ,  1 год назад
Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.»
(Новая страница: «Assembly is done in reverse order. Note: the groove at the bottom of the case should be located on the side of the SIM card slot. All latches must be closed with…»)
(Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.»)
 
(не показано 59 промежуточных версий 3 участников)
Строка 1: Строка 1:
<languages/>
<languages/>
[[File:4_latches.png|300px|thumb|left|Four mounting  latches]]
===Tools===
[[File:First_latch.png|300px|thumb|right|Open the first latch]]
To disassemble the controller, you will need a slotted screwdriver.
[[File:Extracting_the_board.png|300px|thumb|left|Remove the controller board from the case]]
[[File:Bottom_cover_with_cavity.png|300px|thumb|right|Cavity at the bottom of the body]]


The upper part of the controller body is attached to the base on four plastic latches - two on the left and two on the right side. We begin to open the controller case with a latch marked with number "1" in the figure (we start with the latches in the thick part of the body, because in order to open them, you need to make more effort). Use a plastic spatula or screwdriver with a straight slot (the tip can be wrapped with insulation tape or tape, so as not to scratch the plastic case).
===Disassembling===
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case:


Bend the latch with the rotational movement with a little effort (not to break), while shifting the angle of the lower base to itself, as shown in the figure by the arrows. In the same way, open the symmetrical latch, marked with the number "2". The two remaining latches are easily bent by hands to the left and to the right respectively. The lower part of the case is open.
# Place the controller back cover up.
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches.
# Use a screwdriver to bend back the remaining latches and take off the cover.
# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB.


Next, carefully remove the board from the case, which from the connectors of external modules, the Board is slightly raised, and the side wall of the case is pulled over. The directions are shown in the figure. Then take out the Board with a little effort, holding it by the edges.
<gallery mode="packed" heights="150px">
Image: 4_latches.png | Latches
Image: Case2.jpg | Removing the back cover
Image: Case4.jpg | Back cover removed
Image: Case5.jpg | Removing the circuit board
</gallery>


Assembly is done in reverse order. Note: the groove at the bottom of the case should be located on the side of the SIM card slot. All latches must be closed with a click.
=== Assembly ===
Assembly is carried out in the reverse order:  


<br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
#Place the controller board in the case.
#Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch.
#Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case.
#Install the back cover. The cover latches should close whith a clicking sound.
 
<gallery mode="packed" heights="150px">
Image: Case6.jpg | Circuit board installation
Image: Case7.jpg | Front panel switch
Image: Case5.jpg | Installing the connector in the aperture
Image: Case8.jpg | Cover installed
</gallery>
 
===Cover removing and installing===
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case.
 
Removing:
#Place the controller face up.
#Pry the latches on a front cover open with the slotted screwdriver.
#Take off the cover.
 
Installing:
# Place the controller face up.
# Insert the power switch of the controller into the hole on the cover.
# Close all latches carefully.
 
<gallery mode="packed" heights="160px">
Image: Cover_rem1.jpg | Front cover
Image: Cover_rem2.jpg | Latches
Image: Cover_rem3.jpg | Front cover removed
</gallery>
Источник — https://wirenboard.com/wiki/Служебная:Сравнение_версий/20748...66682