16 281
правка
Disassembling the controller case/en: различия между версиями
Disassembling the controller case/en (просмотреть исходный код)
Версия 09:05, 19 августа 2022
, 1 год назадНовая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.»
FuzzyBot (обсуждение | вклад) (Обновление для соответствия новой версии исходной страницы.) |
(Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.») |
||
| (не показаны 3 промежуточные версии этого же участника) | |||
| Строка 1: | Строка 1: | ||
<languages/> | <languages/> | ||
===Tools=== | ===Tools=== | ||
To disassemble | To disassemble the controller, you will need a slotted screwdriver. | ||
===Disassembling=== | ===Disassembling=== | ||
To disassemble the controller, you need to remove the back cover, which is | To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case: | ||
# Place the controller back cover up. | # Place the controller back cover up. | ||
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | ||
# Use a screwdriver to bend back the remaining latches and take off the cover. | # Use a screwdriver to bend back the remaining latches and take off the cover. | ||
# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector. | # Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB. | ||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
| Строка 22: | Строка 18: | ||
</gallery> | </gallery> | ||
=== Assembly === | === Assembly === | ||
Assembly is carried out in the reverse order | Assembly is carried out in the reverse order: | ||
#Place the controller board in the case. | #Place the controller board in the case. | ||
| Строка 39: | Строка 33: | ||
</gallery> | </gallery> | ||
===Cover removing and installing=== | |||
===Cover removing=== | It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case. | ||
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the | |||
Removing: | |||
#Place the controller face up. | #Place the controller face up. | ||
#Pry the latches on a front cover open with the slotted screwdriver. | #Pry the latches on a front cover open with the slotted screwdriver. | ||
#Take off the cover. | #Take off the cover. | ||
Installing: | |||
# | # Place the controller face up. | ||
# | # Insert the power switch of the controller into the hole on the cover. | ||
# | # Close all latches carefully. | ||
<gallery mode="packed" heights="160px"> | <gallery mode="packed" heights="160px"> | ||