12 063
правки
(Новая страница: «|107||input||R|| || || Service register INPUT_REG_SGPC3_RAW_SIGNAL | - | - | - | - | + | |- |108 |input |R |0xFFFF | |Sgpc3 VERSION service register | - | - | -…») |
(Новая страница: «| 110 || holding || RW|| 96 || baud rate / 100 || RS-485 port speed, '''divided by 100'''. Permissible speeds: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200…») |
||
Строка 320: | Строка 320: | ||
| 110 || holding || RW || 96 || | | 110 || holding || RW|| 96 || baud rate / 100 || RS-485 port speed, '''divided by 100'''. Permissible speeds: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 <br>([[UART_Communication_Settings|configure RS-485 communication parameters for wiren Board modbus devices]]) | ||
|colspan="5"| | |colspan="5"|all | ||
| rowspan="3" |>3.1.0 | | rowspan="3" |>3.1.0 | ||
|- | |- | ||
| 111 || holding || RW || 0 || || | | 111 || holding || RW|| 0 || || configure the RS-485 port parity bit. Valid values: 0 - no parity bit (none), 1 - odd (odd), 2 - even (even) | ||
|colspan="5"| | |colspan="5"|all | ||
|- | |- | ||
| 112 || holding || RW || 2 || || | | 112 || holding || RW|| 2 || || number of stop bits of RS-485 port. Valid values: 1, 2 | ||
|colspan="5"| | |colspan="5"|all | ||
|- | |- | ||
| 120 (0x78) || holding || RW || 0 || | | 120 (0x78) || holding || RW|| 0 || non-0 || writing to the register causes the module to restart without saving state | ||
|colspan="5"| | |colspan="5"|all | ||
| | | | ||
|- | |- | ||
| 121 (0x79) || input || R || - || | | 121 (0x79) || input || R || - || mV || current supply voltage of the module | ||
|colspan="5"| | |colspan="5"|all | ||
| | | | ||
|- | |- | ||
| 128 (0x80) || holding || RW || 1 || || Modbus | | 128 (0x80) || holding || RW|| 1 || || Modbus device address | ||
|colspan="5"| | |colspan="5"|all | ||
| | | | ||
|- | |- | ||
| 129 (0x81) || holding || RW || 0 || 0 | | 129 (0x81) || holding || RW|| 0 || 0 or 1 || Go to [[WB-MCU-Flasher|bootloader mode]] | ||
|colspan="5"| | |colspan="5"|all || 4.5.0 | ||
|- | |- | ||
| 200-206 || input || R || | | 200-206 || input || R || see [[#Device signature|Device signature]] || || signature | ||
|colspan="5"| | |colspan="5"|all | ||
| | | | ||
|- | |- | ||
| 220-241 || input || R || || | | 220-241 || input || R | | | | _date__ _time__|| firmware build date | ||
|colspan="5"| | |colspan="5"|all | ||
| | | | ||
|- | |- | ||
Строка 358: | Строка 358: | ||
|0 | |0 | ||
|°C × 100 (signed) | |°C × 100 (signed) | ||
| | |Self-heating temperature compensation for temperature and humidity sensor (value is subtracted from measured temperature) | ||
| + | | + | ||
| - | | - | ||
Строка 366: | Строка 366: | ||
|4.2 | |4.2 | ||
|- | |- | ||
| 250-269 || input || R || | | | 250-269 || input || R | | | / string, null-terminated || firmware version | ||
|colspan="5"| | |colspan="5"|all | ||
| | | | ||
|- | |- | ||
| 270-271 || input || R || || | | 270-271 || input || R|| || 32-bit unsigned int || unique identifier (S/N) | ||
|colspan="5"| | |colspan="5"|all | ||
| | | | ||
|- | |- | ||
|280||input||R|| || | |280||input||R|| || | ||
|| | ||Maximum value of motion sensor with ADC | ||
| - | | - | ||
| - | | - | ||
Строка 384: | Строка 384: | ||
|- | |- | ||
|281||input||R|| || | |281||input||R|| || | ||
|| | ||Value of the motion sensor with ADC | ||
| - | | - | ||
| - | | - | ||
Строка 392: | Строка 392: | ||
| | | | ||
|- | |- | ||
|282||holding||RW||10|| | |282||holding||RW||10||s | ||
|| | ||The width of the time window for calculating the maximum average value of the motion sensor (from 1 to 60 seconds) | ||
| - | | - | ||
| - | | - | ||
Строка 402: | Строка 402: | ||
|- | |- | ||
|283||input||R|| || | |283||input||R|| || | ||
|| | ||Current average value of movement in conventional units | ||
| - | | - | ||
| - | | - |
правки