Translations:Sensors Modbus Management/19/en: различия между версиями

Материал из Wiren Board
(Новая страница: «{| border="1" class="wikitable" style="text-align:center" !Starting address || Quantity || Purpose || In modifications !From firmware version |- | 0 || 1 || style…»)
 
 
Строка 3: Строка 3:
!From firmware version
!From firmware version
|-
|-
| 0 || 1 || style="text-align:left" |Enable buzzer (buzzer) || WB-MSW2, WB-v MSW.3
| 0 || 1 || style="text-align:left" |Enable buzzer (buzzer) || WB-MSW v.3, WB-MSW2
|
|
|-
|-
| 1 || 1 || style="text-align:left" | Forced calibration of the built-in CO2 sensor. Turn on after 20 minutes of operation at a CO2 level of 400 ppm || WB-MSW2
| 1 || 1 || style="text-align:left" | Forced calibration of the built-in CO2 sensor. Turn on after 20 minutes of operation at a CO2 level of 400 ppm || WB-MSW v.3, WB-MSW2
|
|
|-
|-
| 2 || 1 || style="text-align:left" | Turn on the heating (heater) in the temperature and humidity sensor chip HDC1080 || WB-MS (in the 2017 series), WB-MSW2, WB-MSW V. 3
| 2 || 1 || style="text-align:left" | Turn on the heating (heater) in the temperature and humidity sensor chip HDC1080 || WB-MS, WB-MSW v.3, WB-MSW2
|3.2.0
|3.2.0
|-
|-
|3
|3
|1
|1
|The inclusion of a CO2 sensor
|Power on/off of the CO2 sensor
|WB-MSW V. 3
|WB-MSW V. 3
|4.1.0
|4.1.0
|-
|-
| 10 || 1 || style="text-align:left" | Green led on || WB-MSW V. 3  
| 10 || 1 || style="text-align:left" | Green led on || WB-MSW v.3  
|
|
|-
|-
| 11 || 1 || style="text-align:left" | Enable red led || WB-v MSW.3  
| 11 || 1 || style="text-align:left" | Enable red led || WB-MSW v.3  
|
|
|-
|-
|}
|}

Текущая версия на 22:39, 29 марта 2020

Определение сообщения (Sensors Modbus Management)
{|  border="1" class="wikitable" style="text-align:center"
!Начальный адрес || Количество || Назначение || В модификациях
!С версии прошивки
|-
| 0 || 1 || style="text-align:left" |Включение пищалки (buzzer) || WB-MSW v.3, WB-MSW2
|
|-
| 1 || 1 || style="text-align:left" | Принудительная калибровка встроенного датчика CO2. Включать после 20 минут работы при уровне CO2, равном 400 ppm || WB-MSW v.3, WB-MSW2
|
|-
| 2 || 1 || style="text-align:left" | Включение подогрева (heater) в микросхеме сенсора температуры и влажности HDC1080 || WB-MS (2017 г. и новее), WB-MSW v.3, WB-MSW2,
|3.2.0
|-
|3
|1
| style="text-align:left"|Включение датчика CO2 (1-вкл, 0-выкл)
|WB-MSW v.3
|4.1.0
|-
| 10 || 1 || style="text-align:left" | Включение зеленого светодиода || WB-MSW v.3 
|
|-
| 11 || 1 || style="text-align:left" | Включение красного светодиода || WB-MSW v.3 
|
|-
|}
Starting address Quantity Purpose In modifications From firmware version
0 1 Enable buzzer (buzzer) WB-MSW v.3, WB-MSW2
1 1 Forced calibration of the built-in CO2 sensor. Turn on after 20 minutes of operation at a CO2 level of 400 ppm WB-MSW v.3, WB-MSW2
2 1 Turn on the heating (heater) in the temperature and humidity sensor chip HDC1080 WB-MS, WB-MSW v.3, WB-MSW2 3.2.0
3 1 Power on/off of the CO2 sensor WB-MSW V. 3 4.1.0
10 1 Green led on WB-MSW v.3
11 1 Enable red led WB-MSW v.3
Источник — https://wirenboard.com/wiki/index.php?title=Translations:Sensors_Modbus_Management/19/en&oldid=36946