12 063
правки
WB-MIR v1 - Modbus IR Remote Control/en: различия между версиями
WB-MIR v1 - Modbus IR Remote Control/en (просмотреть исходный код)
Версия 12:09, 23 июля 2019
, 4 года назадНовая страница: «== Specifications == {| class="wikitable" ! style="text-align: center;" | Option ! style="text-align: center;" | Value |- ! colspan="2" |Power |- |Supply voltage…»
(Новая страница: «==Installation== The module is mounted on the air conditioner on a double-sided tape so that a small hole of the emitting diode on the reverse side would be locat…») |
(Новая страница: «== Specifications == {| class="wikitable" ! style="text-align: center;" | Option ! style="text-align: center;" | Value |- ! colspan="2" |Power |- |Supply voltage…») |
||
| Строка 19: | Строка 19: | ||
The module is mounted on the air conditioner on a double-sided tape so that a small hole of the emitting diode on the reverse side would be located opposite the IR receiver of the air conditioner, without closing the receiver from the main console of the device. The position is selected experimentally due to the huge variety of designs of air conditioning housings. The same applies to any household devices controlled by IR channel. | The module is mounted on the air conditioner on a double-sided tape so that a small hole of the emitting diode on the reverse side would be located opposite the IR receiver of the air conditioner, without closing the receiver from the main console of the device. The position is selected experimentally due to the huge variety of designs of air conditioning housings. The same applies to any household devices controlled by IR channel. | ||
== | == Specifications == | ||
{| class="wikitable" | {| class="wikitable" | ||
! style="text-align: center;" | | ! style="text-align: center;" | Option | ||
! style="text-align: center;" | | ! style="text-align: center;" | Value | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |Power | ||
|- | |- | ||
| | |Supply voltage | ||
|9 — 24 | |9 — 24 V DC | ||
|- | |- | ||
| | |Power consumption | ||
| | | | ||
0.1 | 0.1 W | ||
|- | |- | ||
| | |Transmitter range | ||
| < | | < 1m | ||
|- | |- | ||
| | | External sensor | ||
| | | Digital temperature sensor DS18B20 can be connected. | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |Control | ||
|- | |- | ||
| | |Management interface | ||
|RS-485 | |RS-485 | ||
|- | |- | ||
| | |Interface isolation | ||
| | |Uninsulated | ||
|- | |- | ||
| | |Communication protocol | ||
|Modbus RTU, | |Modbus RTU, address is set by software, factory settings are indicated on the label | ||
|- | |- | ||
| | |RS-485 interface parameters | ||
| | | | ||
speed 9600 bps; data bits 8; parity N; stop bits 2; | |||
Starting from firmware version '''3.1.0''' parameters interfaces can be configured programmatically: | |||
* | *Speed: 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, 115200 bit/s <br>([[UART_Communication_Settings/en|configure RS-485 communication parameters for wiren Board modbus devices]]) | ||
* | *Data: 8 bit | ||
* | *Parity check: none (default), 1 - odd (odd), 2 - even (even) | ||
* | *Stop bits: 2 (default), 1 | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |dimensions | ||
|- | |- | ||
| | | Size | ||
| 45x35x14 | | 45x35x14 mm | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |Operating conditions | ||
|- | |- | ||
| | | Air temperature | ||
| - | | -40°C to +80°C | ||
|- | |- | ||
| | | Relative humidity | ||
| | | up to 98%,without moisture condensate | ||
|} | |} | ||