12 063
правки
WB-MIR v2 - Modbus IR Remote Control/en: различия между версиями
WB-MIR v2 - Modbus IR Remote Control/en (просмотреть исходный код)
Версия 11:06, 23 июля 2019
, 4 года назадНовая страница: «== Specifications == {| class="wikitable" ! style="text-align: center;" | Option ! style="text-align: center;" | Value |- ! colspan="2" |Power |- |Supply voltage…»
(Новая страница: «==Installation== The module is mounted in the immediate vicinity of the device or inside the housing of a controlled device, such as an air conditioner. If furthe…») |
(Новая страница: «== Specifications == {| class="wikitable" ! style="text-align: center;" | Option ! style="text-align: center;" | Value |- ! colspan="2" |Power |- |Supply voltage…») |
||
| Строка 22: | Строка 22: | ||
The module is mounted in the immediate vicinity of the device or inside the housing of a controlled device, such as an air conditioner. If further training or retraining of the module is planned after installation, the IR receiver should be located in an accessible place. The IR transmitter, placed on a wire, ~140 cm long, is attached next to the IR receiver of the controlled device to a double-sided tape (included) so as to ensure stable transmission of IR control commands, but to retain the ability to control the device from the remote without blocking the IR receiver of the device completely. | The module is mounted in the immediate vicinity of the device or inside the housing of a controlled device, such as an air conditioner. If further training or retraining of the module is planned after installation, the IR receiver should be located in an accessible place. The IR transmitter, placed on a wire, ~140 cm long, is attached next to the IR receiver of the controlled device to a double-sided tape (included) so as to ensure stable transmission of IR control commands, but to retain the ability to control the device from the remote without blocking the IR receiver of the device completely. | ||
== | == Specifications == | ||
{| class="wikitable" | {| class="wikitable" | ||
! style="text-align: center;" | | ! style="text-align: center;" | Option | ||
! style="text-align: center;" | | ! style="text-align: center;" | Value | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |Power | ||
|- | |- | ||
| | |Supply voltage | ||
|9 — 24 | |9 — 24 V DC | ||
|- | |- | ||
| | |Power consumption | ||
| | | | ||
0.1 | 0.1 W | ||
|- | |- | ||
| | |Transmitter range | ||
| < | | < 1m | ||
|- | |- | ||
| | | External sensor | ||
| | | Digital temperature sensor DS18B20 can be connected. | ||
|- | |- | ||
!colspan="2" | ''' | !colspan="2" | '''Terminals and wire section''' | ||
|- | |- | ||
|| | || Recommended wire cross-section with NSUI, mm<sup>2</sup>|| 0,75 — 1 | ||
|- | |- | ||
|| | || Length of the standard sleeve NSUI, mm || 8 | ||
|- | |- | ||
|| | || Torque of screws, N∙m || 0,2 | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |Control | ||
|- | |- | ||
| | |Management interface | ||
|RS-485 | |RS-485 | ||
|- | |- | ||
| | |Interface isolation | ||
| | |Uninsulated | ||
|- | |- | ||
| | |Communication protocol | ||
|Modbus RTU, | |Modbus RTU, address is set by software, factory settings are indicated on the label | ||
|- | |- | ||
| | |RS-485 interface parameters | ||
| | | | ||
speed 9600 bps; data bits 8; parity N; stop bits 2; | |||
Starting from firmware version '''3.1.0''' parameters interfaces can be configured programmatically: | |||
* | *Speed: 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, 115200 bit/s <br>([[UART_Communication_Settings/en|configure RS-485 communication parameters for Wiren Board modbus devices]]) | ||
* | *Data: 8 bit | ||
* | *Parity check: none (default), 1 - odd (odd), 2 - even (even) | ||
* | *Stop bits: 2 (default), 1 | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" | Number of stored IR commands | ||
|- | |- | ||
| | |Number of teams | ||
| | | | ||
* | * Firmware to version ''3.7.2'' inclusive: ''7'' | ||
* | * Firmware from version '''4.4.0''': '''40''' | ||
* | * Firmware versions older than 3.7.2 and up to 4.4.0 supported up to ~80 commands, but did not work correctly with some devices. | ||
|- | |- | ||
| | |Command duration | ||
| | | The maximum command length is 508 registers, plus two registers indicates the end of the command.Each register encodes the duration of a high or low signal level (sequentially) in microseconds. | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" | dimensions | ||
|- | |- | ||
| | | L x W x h | ||
| | | | ||
* 40x15x11 | * 40x15x11 mm; length of connector cable transmitter adds 30 mm to the width of the housing | ||
|- | |- | ||
! colspan="2" | | ! colspan="2" |operating Conditions | ||
|- | |- | ||
| | | Air temperature | ||
| - | | -40°C to +80°C | ||
|- | |- | ||
| | | Relative humidity | ||
| | | up to 98%,without moisture condensate | ||
|} | |} | ||