История
22 апреля 2021
FuzzyBot переименовал страницу WBIO-AI-DV-12 Analog Inputs 4-20mA/en в WBIO-AI-DV-12/4-20mA Analog Inputs/en без оставления перенаправления: Часть переводимой страницы WBIO-AI-DV-12 Analog Inputs 4-20mA.
мЧасть переводимой страницы WBIO-AI-DV-12 4-20MA.
+11
FuzzyBot переименовал страницу WBIO-AI-DV-12 4-20MA/en в WBIO-AI-DV-12 Analog Inputs 4-20mA/en без оставления перенаправления: Часть переводимой страницы WBIO-AI-DV-12 4-20MA.
м
16 июля 2019
Новая страница: «Starting from May 20,2019 components, providing the error is not more than 0.1%+0.003 mA, are installed in WBIO-AI-DV-12/4-20MA»
−59
Новая страница: «====Scheduled fix===»
−41
Новая страница: «no»
−4
Новая страница: «====Workarounds====»
−10
Новая страница: «The nominal value of the input protective resistor is selected too large relative to the internal resistance of the ADC.»
−75
Новая страница: «====Reasons and detailed description====»
−21
Новая страница: «Current measurement error in WBIO-AI-DV-12/4-20MA can be up to 1%.»
−39
Новая страница: «====Description====»
−5
Новая страница: «WBIO-AI-DV-12/4-20MA shipped before May 20, 2019.»
−17
Новая страница: «==== Affected devices ====»
−27
Новая страница: «=== ERRAIDV01: Reduced precision of inputs ===»
−21
Новая страница: «== Bugs and features ==»
−40
Новая страница: «==Device pictures and drawings == {{WBPicturesNoDrawing|2}}»
−34
Новая страница: «--»
−1
Новая страница: « For models designed to measure current, the '''scale' ''factor must be set to 0.1»
−109
Новая страница: «{| class="wikitable" style="text-align:center" |+ Dependence of the input operation mode on the installed jumper and scaling factor !'''The presence of the jumper…»
−241
Новая страница: «{| class="wikitable" style="text-align:center" |400px|thumb|right|Add channel list |File:Ai-dv-12-only-scale.png|400p…»
−103
Новая страница: «For each channel, you can specify a conversion factor (scale) corresponding to the measurement mode. Restartujte service wb-mqtt-serial after changes: <code>> ser…»
−604
Новая страница: «Previously, when connecting the module via WB-MIO or WB-MIO-E, there was no possibility to select the input mode from the web interface. We recommended creating c…»
−335
Новая страница: «'''Warning, the information below is outdated and will be deleted!'''»
−31
Новая страница: «The WBIO-AI-DV-12 module can also be connected via the interface converter WB-MIO. Two device templates can be used: WBIO-AI-DV-12-50V and WBIO-AI-D…»
−394
Нет описания правки
−6
Новая страница: «File:Scale_WBIO_AI_DV_12.png|500px|thumb|right|the value of the scale factor of the dimensions '''scale''' is chosen equal to 0.2126 for measuring voltage of ±…»
−175
Новая страница: «Unlike other WBIO modules, only one instance can be connected to a single controller or interface module.»
−118
Новая страница: «<!-- == Connection via WB-MIO interface converter ==»
−53
Новая страница: «{| class="wikitable" | 500px|thumb|center|login mode settings | File:WEB-WBIO-AI-DV-12_4-20MA.png|500px|thumb|center|Display inputs with d…»
−448
Новая страница: «After the necessary settings and saving changes, the device will be displayed in the '''''Devices'''''tab.»
−71
Новая страница: «Now you need to activate the desired mode in the tab '''''Channels'''''. Channels are denoted as '''''Channel Ax''''', where 'x' corresponds to the entry number.…»
−126
Новая страница: «{| class="wikitable" | 500px|thumb|center|Desired configuration file | File:DV12WebInterface2.jpg|500px|thumb|center|Module select…»
−43
Новая страница: «To connect, you need to dock the WBIO-AI-DV-12 4-20 mА module to the right of the Wiren Board controller and make sure that all the connector pins on the module…»
−401
Новая страница: «'''Unlike other WBIO modules, only one instance can be connected to a single controller or interface module.'''»
−112
Новая страница: «== Connection to the controller ==»
−20
Новая страница: «== Current measurement == 500px|thumb|left|Current sensor connection»
−41
Новая страница: «{| class="wikitable" !colspan="2" | '''Terminals and wire section''' |- || The recommended wire cross section with pin bushing insulated tip, mm<sup>2</sup> ||…»
−51
Новая страница: «mini|420x600px|overall dimensions {| class="wikitable" !Parameter !Value |- ! colspan="2" |General |- |Number of inputs |12 |- |Input type |an…»
−311
Новая страница: «==Technical specifications==»
−30
Новая страница: «The module is galvanically isolated from the controller circuits, including the iGND line.»
−51
Новая страница: «For easy connection, each pair of inputs is output to one of 6 terminals. In addition to the inputs, each terminal block has +5 V and iGND lines, but the maximum…»
−218
Новая страница: «The module contains 12 current inputs A1 — A12 for the connection of current outputs (0) 4 — 20 mA ([https://en.wikipedia.org/wiki/Current_loop "current loop"]).»
−121
Новая страница: «==Design==»
−23
Новая страница: «'''[https://wirenboard.com/ru/product/WBIO-AI-DV-12_4-20MA/ Buy WBIO-AI-DV-12_4-20MA in the online store ]'''»
−25
Новая страница: «'''IMPORTANT: unlike other WBIO modules, only one instance can be connected to a single controller or interface module.'''»
−119
Новая страница: «The module is designed for industrial and home automation systems and is used to measure current signals in the range up to 20 mA. A typical application of the mo…»
−271
Новая страница: «{{DISPLAYTITLE: WBIO-AI-DV-12 4-20мА analog inputs module}} {{#vardefine:ProductFullName2|Analog inputs module WBIO-AI-DV-12 for measuring analog signals 4-20…»
−120
Новая страница: «WBIO-AI-DV-12 4-20MA»
+13 601