История
3 июля 2019
Новая страница: « == Device pictures and drawings == {{WBPicturesNoDrawing|1}}»
−32
Обновление для соответствия новой версии исходной страницы.
+1
Новая страница: «Wiren Board 5: WB root password recovery»
−42
Новая страница: «Working with GPIO — how to work directly with GPIO.»
−34
Новая страница: «rev. 5.5 (5.6, 5.6.1), rev. 5.8 (5.9), Wiren Board 5:Список GPIO/en|rev.…»
+9
Новая страница: «Table of matching processor and GPIO signals on the board for revisions:»
−52
Новая страница: « Hardware revisions — the description of changes in the controller board.»
+3
Новая страница: « Hardware errors/features of Wiren Board 5 found in the operation of the controller.»
−79
Новая страница: «The article Wiren Board 5: Hardware describes some of the features of work and the device inputs, the power supply…»
−28
Новая страница: «thumb|400px|Board side»
−38
Новая страница: «== Detailed technical description of the controller board ==»
−22
Новая страница: «Connection of peripheral devices»
−50
Новая страница: «Supported Devices»
−32
Новая страница: «Devices of our production with the RS-485 interface»
−38
Новая страница: «Valid power range is '''7-28V'''. The average consumption of the Board is 1.5-2 watts. But since the GSM module pulse consumes up to 8 watts, it is recommended t…»
−152
Новая страница: «For backup power, you can connect the internal module WBMZ-BATTERY with Li-Ion (Li-Pol)…»
−70
Новая страница: «It is possible to simultaneously connect the sources to different inputs, including different voltages.»
−75
Новая страница: «* Power-over-Ethernet (PoE Passive). Read more Power over Ethernet.»
−36
Новая страница: «* Terminals Vin and GND in the controller of audit 5.8 and above: two terminal Vin, to which you can connect two independent power supply for redundancy. The grou…»
−146
Новая страница: «* DC jack - standard plug connector (5.5x2.1mm) on the left side of the case.»
−50
Новая страница: «The controller has three external inputs for power connection:»
−53
Новая страница: «== Power Supply ==»
−2
Новая страница: « Hardware watchdog disable»
−53
Новая страница: «A separate hardware watchdog that reboots the entire controller on power when the software freezes.»
−68
Новая страница: «== Watchdog ==»
−25
Новая страница: «Revisions 5.3 and 5.6 also contain: *IrDA * Digital audio output - S/PDIF, TOSLINK connector.»
−98
Новая страница: «The real-time clock RTC is powered by an internal backup battery.»
−67
Новая страница: « "Buzzer" — beeps, its frequency is adjustable.»
−54
Новая страница: «Debug port - you can directly access the controller console by connecting to it. Through it you can also interact with the bootloader and…»
−209
Новая страница: «== Other interfaces ==»
−17
Новая страница: «Type "250" terminals are used as interface terminals in the controller. These are self-locking clips. When the cleaned single-wire is inserted into the socket, it…»
−315
Новая страница: «All inputs are protected against supply voltage (up to 28 V) and impulse noise.»
−58
Новая страница: «|- ! colspan="8"| Bottom row, right block |- | '''A1-A4''' | | 28V , 2A || High Z || Управление низковольтной нагрузкой/en|open…»
−363
Новая страница: «| "'O1-O3"' || | ||| || |Inputs/outputs of the 2nd extension module»
−26
Новая страница: «{| border="1" width="700" class="wikitable" style="text-align:center" | '''signature''' || "'Max. V, I"' | width="10%" | "'state"' "'default"' | width="60%"|"'…»
−167
Нет описания правки
Новая страница: «thumb|400px|Working with WAGO 250 terminals»
−28
Новая страница: «== Terminal blocks ==»
−3
Новая страница: «"R2 input only is only in version 5.3."»
−19
Новая страница: «== Resistive inputs R1 and R2 == Can operate in modes: * resistance measurements 1-30kω * voltage measurements in the range of 0-3.0 V * digital input»
−103
Новая страница: «* Digital input — is triggered when the voltage at the terminal is 5 V»
−54
Новая страница: «* Analog input with 0-28V measurement range.»
−39
Новая страница: «* Output open collector - key (3A/30V), closing the ground output.»
−54
Новая страница: «Universal channel Ah combines three functions and can work as:»
−74
Новая страница: «== Universal inputs/outputs A1-A4 ==»
−26
Новая страница: «It is convenient to use +5V output to power the sensors. It is protected from short circuit and high voltage. When the controller is powered by a battery, the +5…»
−182
Новая страница: «''' 1-Wire''' — is a bus for connecting external sensors on two or three wires. Since this is a bus, you can connect multiple devices to the same…»
−147
Новая страница: «''' CAN''' is the standard for two-wire bus communication. The controller is multiplexed (output to the same terminals) with a second RS-485 port.»
−102
Новая страница: «Basically in Wiren Board, driver WB-mqtt-serial works through the system of MQTT-messages with connected RS-485…»
−38
Новая страница: « Setting up the connection of devices is carried out in the web interface.»
−43