История
24 ноября 2015
Нет описания правки
−6
Нет описания правки
−8
Нет описания правки
−22
Новая страница: «== Operation with screw terminals ==»
−21
Новая страница: «Wiren Board allows to connect interior WBMZ-BATTERY backup power supply module with Li-Ion…»
−72
Новая страница: «=== Battery ===»
−15
Новая страница: «It is possible to power the device via an Ethernet cable. Ref.Power over Ethernet.»
−46
Новая страница: «A standard connector jack 5.5x2.1 mm is provided for connection to the power source. Input power can also be connected to Vin and GND terminals.»
−40
Новая страница: «Allowed voltage range is 7-28 V. Average power consumption of the board is 1.5-2 W, but the GSM module may temporally consume up to 8 W. Therefore, it is recommen…»
−130
Новая страница: «=== External power source ===»
−26
Новая страница: «== Power Supply ==»
−2
Новая страница: «Look the relevant articles to describe the connection and operation of the software:»
−37
Новая страница: «== Extension modules ==»
−16
Новая страница: «In an alternate mode while the current source is unactivated, the input is tucked up to ground. A logical zero corresponds to the input, to which nothing is conne…»
−251
Новая страница: «While the current source is activated (the default mode) the input is tucked up to the power supply. If no entry to connected, this state is perceived as a logica…»
−281
Нет описания правки
+1
Нет описания правки
+4
Новая страница: «Inputs R1-R2 also act as binary inputs.»
−41
Новая страница: «Each input also can be switched to a conventional analog input settings. In this mode, the power supply is t…»
−133
Новая страница: «In mode by default each terminal is connected to internal adjustable current source. The controller provides a predetermined current through the sensor, thus mea…»
−197
Новая страница: «== Resistive Inputs R1 and R2 ==»
−16
Новая страница: «Аx channels support binary input function DI: more than 3V at the terminal is considered as triggering of the input.»
−125
Новая страница: «Input stage of Ax channel consists of an analogue-to-digital converter ADCx and an input resistor Rx. The ADC has a high impedance, so it doesn't affect the chan…»
−524
20 ноября 2015
Нет описания правки
−22
Новая страница: «*Inactive (open), high impedance. Such outputs are called “open collectors”»
−88
Новая страница: «*Active (closed); channel output is connected to ground (0V)»
−23
Новая страница: «Output stage consists of the Tx switch. The Tx switch can connect the corresponding output with ground. The state of the switch is controlled by logic circuits i…»
−102
Новая страница: «Multifunctional channels consist of input and output stages are connected in parallel, as well as protective diodes (connected to one terminal of the channel).»
−112
Новая страница: «== Multifunctional inputs/outputs A1-A4==»
−20
Новая страница: «#All inputs are protected from applying the power supply voltage (up to 24 V) and transient noise. #Wiren Board 5 is protected against reverse polarity #Low-side…»
−57
Новая страница: «== Input protection ==»
−9
Нет описания правки
−193
Нет описания правки
+192
Нет описания правки
−192
Нет описания правки
−4
Новая страница: «|- | '''L''' || 30 V || 0V || rowspan="2"|connector CAN or RS-485 (/dev/ttyAPP4). Connection RS-485: A to terminal '''L''', B to te…»
−23
Новая страница: «| '''A''' || 30 V || 0V || rowspan="2"|connector RS-485 (/dev/ttyAPP1) |- | '''B''' || 30 V || +5V |-»
+1
Новая страница: «|- | '''A1''' || rowspan="4"| 24V , 2A || rowspan="4"| High Z || rowspan="4" |Special:MyLanguage/Управление низковольтной нагрузк…»
−119
Нет описания правки
Нет описания правки
Нет описания правки
+34
Нет описания правки
Новая страница: «Some terminal blocks can be used to perform more than one function. See the detailed description of input/output and Special:MyLanguage/Port multiplexing|the Po…»
−118
Новая страница: «== Terminal blocks ==»
−3
Нет описания правки
Нет описания правки
−1
Нет описания правки
+1
Нет описания правки
+1
Нет описания правки
−1
Нет описания правки
−1