История
3 октября 2022
Новая страница: «For more information see the «AmadeuS» wiki article «[http://www.armadeus.com/wiki/index.php?title=CAN_bus_Linux_driver CAN bus Linux driver]».»
−50
Новая страница: «The <code>cansend</code> and <code>candump</code> utilities are included in the controller's standard software package. If for some reason they are not there, you can install the <code>can-utils</code> package: <syntaxhighlight lang="bash"> apt update && apt install can-utils </syntaxhighlight>»
−201
Новая страница: «Command examples: * Sending four bytes with address 123: *:<syntaxhighlight lang="bash"> cansend can0 123#DEADBEEF </syntaxhighlight>»
−22
Новая страница: «* Show incoming packets: *:<syntaxhighlight lang="bash"> candump can0 </syntaxhighlight>»
−120
Новая страница: «==== Using standard linux tools (manually) ====»
−74
Новая страница: «==== Using standard linux tools (automatically) ==== The '''Network Interfaces''' section of the web interface is a wrapper around the <code>/etc/network/interfaces</code> file, so CAN configuration can be done using the debian network management service. For this you need: # Add to <code>/etc/network/interfaces</code> an entry like this: #:<syntaxhighlight lang="bash"> allow-hotplug can0 iface can0 can static bitrate 125000 </syntaxhighlight> # Switch RS-48...»
−238
Новая страница: «The CAN interface will rise by itself when: * system boot - service <code>wb-hwconf-manager</code> is responsible for this, * change the RS-485/2 port mode to «CAN».»
−74
Новая страница: «Actions take place in the '''Configs''' section of the web-interface: # On the '''Network Interfaces''' tab, add a new interface <code>can0</code> (see screenshot). Click the '''Save''' button. # Switch the <code>RS-485/CAN</code> port to CAN mode: on the '''Hardware Modules Configuration''' tab, select the settings '''RS485-2/CAN interface config''', select in the '''Module type''' «CAN interface» and click the '''Save''' button.»
−154
Новая страница: «==== Via web interface ==== To configure via the web interface, you need to update the <code>wb-mqtt-confed</code> package to version 1.2.3+»
−61
Новая страница: «== Setting == 300px|thumb|right|Configuring the can interface. Allow-hotplug allows the interface to rise automatically 300px|thumb|right|Setting the RS485-2 port to CAN mode and enabling the can driver in linux»
−102
Новая страница: «The work takes place through a standard Linux subsystem - SocketCAN. CAN ports are similar to network interfaces <code>can0</code> or <code>can1</code>, depending on the controller model. For CAN to work on controllers up to version 6.7.x, you need a terminator jumper on the port. Starting from version 6.7.x, the terminator is controlled by software and turns on automatically.»
−234
Обновление для соответствия новой версии исходной страницы.
+3394
29 мая 2019
Нет описания правки
−19
Новая страница: «For more information, see the [http://www.armadeus.com/wiki/index.php?title=CAN_bus_Linux_driver article].»
−29
Новая страница: «Note that in case of problems on the bus (no terminator, no receiving device, short circuit), the controller may stop working. To get started again, run»
−210
Новая страница: «show statistics:»
−22
Новая страница: «show incoming packages:»
−28
Новая страница: «sending 4 bytes with address 123:»
−20
Новая страница: «Configuring the interface»
−28
Новая страница: «Switch the RS-485/CAN port to CAN mode: On the Hardware Modules Configuration tab, select 'RS485-2/CAN interface config' settings, select 'Module type' '''CAN int…»
−74
Новая страница: «For easy work with CAN, you need to install the package 'apt-get install can-utils'»
−25
Новая страница: «The work takes place through the standard Linux SocketCAN subsystem.»
−37
Новая страница: «Can ports are available in the system as can0 or can1 network interfaces, depending on the controller model.»
−70
Новая страница: «CAN»
+1719