История
18 июля 2019
Нет описания правки
−39
Новая страница: «=== Board drawing=== Файл:WB 2.8 chertej.pdf»
−10
Новая страница: «See Wiren Board v.2.8 source files»
+33
Новая страница: «== Source files ==»
−17
Новая страница: «Output to uext1 connector (black connector with ten pins on the long side of the Board).»
−62
Новая страница: «===GPIO=== See List of GPIOs.»
+16
Новая страница: «| Terminal strip 9 || GPIO operation/ADC/en || 3.3 V, 10mA|| 2 || 13 @ CON1 || 47K pull-up|| ADC channel 7 |- | Terminal strip 10 || GPIO/en|GPI…»
−202
Новая страница: «| Terminal strip 4 || FET/ADC/en || 30V, 2A|| 34 || 5 @ CON1 || Closed || open collector Output, ADC/en channel 1 |- | Ter…»
−302
Новая страница: «| Terminal strip 3 || FET/ADC/en || 30V, 2A|| 33 || 4 @ CON1 || Closed || open colle…»
−27
Новая страница: «=== Terminal blocks=== See also Low voltage load control. {| border="1" | Terminal ||…»
−120
Новая страница: «=== ADC=== The user can access 7 ADC channels displayed on the terminals (see table). The maximum measured voltage is 5V. See. ADC/en.»
−119
Новая страница: «'''It is necessary to meet the battery polarity!'''»
−43
Новая страница: «In the current version there is no protection against charging at low temperatures. Be careful, the batteries deteriorate from this.»
−104
Новая страница: «===Battery=== The Wiren Board allows you to connect a Li-Ion (Li-Pol) battery with a maximum voltage of 4.2 V. When you connect the power, the battery is charged…»
−233
Новая страница: «See Power over Ethernet/en.»
−10
Новая страница: « Power over Ethernet is supported via cable [http://ru.wikipedia.org/wiki/Power_over_Ethernet#Passive_PoE Passive PoE] with voltage from 7 to 24 Volts. Power is…»
−176
Новая страница: «'''Connecting PoE with the power supply causes damage to the power supply.'''»
−75
Новая страница: «===Power over Ethernet=== '''Only in PoE-enabled version. Versions with PoE support have the inscription HLJ-6115ANL on the Ethernet-connector. Connecting Power o…»
−137
Новая страница: «Connect the locking button or toggle switch to the holes on the Board. When the contacts are closed, the Board is disconnected. The battery continues to charge.»
−116
Новая страница: «'''The On/Off Button'''»
−12
Новая страница: «===Power supply=== Supply voltage is 4.7-22V. The average consumption of the board is 1.5-2 watts. But since the GPRS module consumes up to 8W impulsively, it is…»
−112
Новая страница: «One of the corners is made with perforation for breaking. This makes it easy to install in the housing, where the corners are located under the cover screws rack.»
−75
Новая страница: «The distance between the mounting holes is 96 and 46 mm.»
−36
Новая страница: «=== Dimensions=== Board dimensions - length - 105 mm (+ 3 mm Ethernet and USB connectors), width - 54 mm (+3 mm power connector), height - 20 mm.»
−57
Новая страница: «thumb|400px|Wiren Board rev. 2.8 thumb|400px|Wiren Board rev. 2.8 Файл:Питание.PNG|…»
−14
Новая страница: «Wiren Board consists of two printed circuit boards: * modified iMX233-OLinuXino-MICRO/en * main board Wiren Board Main board contains: * Wi-Fi/en based on…»
−237
Новая страница: «Here is a description of Wiren Board controller version 2.8.»
−4
Новая страница: «==Description==»
−7
Новая страница: «Hardware Overview rev. 2.8-rus»
+8675