История
27 ноября 2019
16 июля 2019
Новая страница: «List of known faults»
−37
Новая страница: «== Known faults and bugs ==»
−24
Новая страница: «== Device firmware update == Starting with the new firmware versions of the device, the firmware update functionality (firmware) via the Modbus Protocol is suppor…»
−448
Новая страница: «Back to peripheral devices list»
−36
Новая страница: «Details of the work with the module via Modbus Protocol is written in Relay Modules Modbus Management . There you can also…»
−130
Новая страница: «==Modbus Control==»
−20
Новая страница: «== Relay operation in case of power failure == Depending on the value written to the storage register 0x06, after the power is turned off and restored, the relay…»
−303
Новая страница: «A button connected to input 0 allows you to turn off all the relays included in the module with a single press. Pressing again will turn on all the relays that we…»
−411
Новая страница: «The Safety Timer slider allows you to set the shutdown time (in seconds) of all outputs when there is no communication with the Wiren Board (0 – the safety time…»
−435
Новая страница: «Using virtual switches K1-K6 in the web-interface, you can control the corresponding outputs of the module and monitor their status. If the relay is turned on or…»
−397
Новая страница: «{| border="0" class="wikitable" style="text-align:center" |- |300px|thumb|center|Relay channel control buttons |File:Web_options…»
−131
Новая страница: «The relay corresponds to the position of the outputs: {| class="wikitable" !K1/ K4 !K2/ K5 !K3/ K6 ! !OUT1/ OUT2 |- | rowspan="2" |OFF |OFF | rowspan="2" |OFF | |…»
−28
Новая страница: «The device uses the WB-MR6F template. Each channel corresponds to three switches that control three relays in the group: K1, K2, K3 belong to the first channel, K…»
−134
Новая страница: «== Control of the module via the Wiren Board web interface ==»
−26
Новая страница: «File:Installation_WBMR6C_+_WB5.png|650px|thumb|center|Sample installation and connection of WB-MR6C module.Scheme for WB-MR6F is the same. The choice of a quali…»
−112
Новая страница: «The module must be installed to meet the requirements of electrical safety and to prevent accidental contact of contacts under high voltage. The module must be op…»
−276
Нет описания правки
+17
Новая страница: «If the device is the last one on the RS-485 line, a 120 Ohm resistor-terminator must be installed between its inputs A and B. Practice shows that in the case of b…»
−276
Новая страница: «The current flowing when the button or switch is closed is small, so the type of button or switch can be any. Despite the built-in protection against rattle, choo…»
−250
Новая страница: «When connecting the switching devices to the relay contacts, it is important not to exceed the recommended current of '''3 A'''.»
−61
Новая страница: «The screw-free terminal blocks on the relay board are used to connect power lines, control (RS-485) and input contacts. When using handpieces for installation of…»
−381
Новая страница: «== Installation== The relay module is mounted on a standard 35 mm wide DIN rail and occupies a width of 3 DIN modules.»
−71
Новая страница: «At the physical level, the module is connected via RS-485 interface. Modbus RTU Protocol is used to control the WB-MR6F. In Wiren Board devices, M…»
−274
Новая страница: «===Data exchange===»
−14
Новая страница: «= = = Module dimensions === 300px|thumb|left| the dimensions of the modules in the housing 3 DIN The overall dimensions of the module are 53.…»
−91
Новая страница: «|Functions | * General purpose inputs * Signal count * Direct control of relay channels * Simultaneous disconnection of the entire load * Remember the relay statu…»
−834
Новая страница: «{| border="1" class="wikitable" style="text-align:left" |- !Parameter !Value |- ! colspan="2" |Power |- |Supply voltage |9 — 28 V DC |- |Power consumption | *In…»
−833
Новая страница: « Our detailed article in russian on habr.com about the choice of relay parameters for the switched load: https://habr.com/ru/company/wirenboard/blog/422197/»
−48
Новая страница: «==Technical specifications==»
−31
Новая страница: «It is not recommended to use switches (e.g. buttons with fixation) in the trigger mode of inputs. Input interference may be perceived as a short release/push of t…»
−233
Новая страница: «The inputs have two modes of operation: trigger mode (for control with buttons) and repeat mode (for control with switches). In the trigger mode, to change the st…»
−474
Новая страница: «Each input controls the state of the corresponding relay.»
−47
Нет описания правки
−9
Новая страница: «=== Inputs=== 420px|thumb|left|Closed input in trigger mode may be unstable The inputs of the modules WB-MR6F displayed on the pressure…»
−254
Новая страница: «The table below lists the specifications and conditions of use of the WB-MR6F relay module. Each output of the module is protected from arcing when the varistor c…»
−351
Новая страница: «The module can be timer enabled safe mode, which at the termination of the data exchange through Modbus module disables all the relays after a specified time.»
−141
Новая страница: «Each of the two channels of the module consists of two rocker relays and one relay with normally open contacts. Depending on the position of the relay, each of t…»
−206
Новая страница: «=== Outputs=== left|mini|350х350пкс|Diagram of one channel of the module The module has 6 HF32F relays ([http://www.hong…»
−57
Новая страница: «The channels are designed for a 3A load.»
−22
Новая страница: «Incorrect software settings and mechanical faults of the relay can not cause a short circuit of the input voltages Vx between themselves because of the device des…»
−179
Новая страница: «Specialized two-channel relay module WB-MR6F is designed for step load control, for example, for three-stage speed control of convector fans.»
−217
Новая страница: «=== Purpose ===»
−60
Новая страница: «WB-MR6F Modbus Relay Module»
+20 148