История
6 сентября 2022
19 июля 2019
Новая страница: «Background information on test audits: * Wiren Board 5: Список GPIO (rev 5.1)/en»
−40
Новая страница: «===Serial ports === {| class="wikitable" !Port ! |- |/dev/ttyAPP0 |GSM/EDGE |- |/dev/ttyAPP1 |RS-485 port on RS-485 terminals |- |/dev/ttyAPP2 |UART port on first…»
−123
Новая страница: «{| border="1" | sodim output || GPIO ||imx287 output || pin || function |-»
−17
Нет описания правки
+2
Новая страница: «"'The connector is not soldered to devices as standard"'»
−59
Новая страница: «=== FFC extension connector ===»
−14
Новая страница: «{| border="1" | sodim output || GPIO ||imx287 output || pin || function |- |94 || 0-21 || N8 || RFM69_MOSI || MOSI |- | 138 || 0-0 || U8 || RFM69_MISO || MISO…»
−32
Новая страница: «Connected via SPI1.»
−10
Новая страница: «=== Radio module ===»
−11
Новая страница: «See also GPIO Howto»
−34
Новая страница: «{| border="1" | sodim output || GPIO ||imx287 output || pin || function |- |44 || 3-10 || H6 || INT || Abort |- | 46 || 3-25 || D8 || I2C0_SDA || I2C0 hardware |-…»
−62
Новая страница: «=== GPIO on I/O extension connector ===»
−38
Новая страница: «{| border="1" | sodim output || GPIO |GPIO number||imx287 output || pin || function |-»
−16
Новая страница: «===GPIO on MOD3 extension connector===»
−20
Новая страница: «{| border="1" | sodim output || GPIO |GPIO number|| imx287 output |pinmux pad name|| pin || function |-»
−17
Новая страница: «=== GPIO on MOD2 extension connector ===»
−18
Новая страница: «{| border="1" | sodim output || GPIO |GPIO number|| imx287 output |pinmux pad name|| pin || function |-»
−17
Новая страница: «300px|thumb|right|Pinout connector for extension modules»
−39
Новая страница: «=== GPIO on MOD1 extension connector ===»
−18
Новая страница: «| 86 || 3-20 ||| G7 || 1-wire |- | 84 || 3-22 ||| F7 || 1-Wire transistor pull-up |- | 52 || 3-29 (PWM4) |125|| E10|| irda out |- | 61 || 3-14 |||L6 ||…»
−88
Новая страница: «{| border="1" | sodim output || GPIO |GPIO number||imx287 output || function |-»
−14
Новая страница: «=== GPIOs for internal use ===»
−39
Новая страница: «| A4 (out) || ADC/'''FET'''/DI || 98 || 0-20 || N6 ||Open collector output; |-»
−27
Новая страница: «| A3 (out) || ADC/'''FET'''/DI || 100 || 0-24 || R6 ||Open collector output; |-»
−27
Новая страница: «| A2 (out) || ADC/'''FET'''/DI || 102 || 0-16 || N7 ||Open collector output; |-»
−27
Новая страница: «| A1 (out) || ADC/'''FET'''/DI || 104 || 0-26 || P6 ||Open collector output; |-»
−27
Новая страница: «{| border="1" | terminal strip || function|| sodim output || GPIO ||imx287 output || comments |-»
−30
Новая страница: «=== GPIO for transistors ===»
−16
Новая страница: «{| border="1" | terminal strip || function|| sodim output || GPIO ||imx287 output || comments |-»
−30
Новая страница: «=== GPIOs on terminals ===»
−12
Новая страница: «{| border="1" | terminal strip || function|| sodim output || GPIO ||imx287 output || comments |- | A1 || FET/'''ADC'''/DI || 111 || LRADC1 || C9 || |- | A2 ||…»
−30
Новая страница: «=== АDC ===»
−2
Новая страница: «9. /dev/ttyAPP4 RS-485 port on RS-485/CAN terminals switched to legs 9 (TX) and 13 (RX), RTS remained at 78.»
−38
Новая страница: «8. Порт GSM получил RTS (pin 57) и CTS (pin 59).»
−14
Новая страница: «7. MOD3 supply management - 15 pin»
−26
Новая страница: «6. CS (MOD3) - 21 pin.»
−7
Новая страница: «5. CS (MOD2) changed from 12 to 23 pin.»
−18
Новая страница: «4. CS (MOD1) changed from 11 to 12 pin.»
−18
Новая страница: «3. SPI is now common on all three connectors (SSP2), chip selects are different.»
−26
Новая страница: «2. SDA Mod1 migrated to 11 pin.»
−31
Новая страница: «1. Swapped WATCHDOG_IN (37) and MOD1_SCL (35)»
−23
Новая страница: «== Changes compared to version 5.3 ==»
−34
Новая страница: «The article describes the connection of the built-in peripherals to the processor signals for the ''' Wiren Board 5 (rev. 5.5, 5.6, 5.6.1)'''.»
−66
Новая страница: «Wiren Board 5.5: List of GPIOs»
+8897