История
24 мая 2019
15 января 2016
Нет описания правки
−1
Нет описания правки
−2
Нет описания правки
Нет описания правки
+1
Нет описания правки
Нет описания правки
+1
Нет описания правки
−3
Нет описания правки
+24
Нет описания правки
−4
Нет описания правки
+25
Нет описания правки
+19
Нет описания правки
+19
Нет описания правки
+16
Нет описания правки
+23
Новая страница: «Schematic test stand - thumb|500px|Schematic test stand»
−35
Новая страница: «=== Example of connection devices ===»
−25
Новая страница: «If the RS-485 network is long enough, then it is recommended to use Wiren Board 5: Модуль расширения RS485-ISO|extension module with galvanicall…»
−141
Новая страница: «Wiren Board 5 has two RS-485 port. The second port is multiplexed with the port CAN (L with A, H with B) Line A B is connected to terminals A and B respectively.…»
−133
Новая страница: «See RS-485.»
−13
Новая страница: «== Connecting to RS-485 network ==»
−14
Новая страница: «When using a passive power supply pin of each sensor is connected to the earth wire. In this case, the bus consists two wires attached, respectively, to '1-Wire "…»
−192
Новая страница: «Ground connect to GND or common ground bus. The data line to 1-W terminal. The supply line to 5Vout terminal (internal power supply). It is allowed to use externa…»
−183
Новая страница: «== Connecting to the 1-Wire network ==»
−9
Новая страница: «Expansion module contains TVS, protect the relay contacts from arcing. Exterior protective components is not required.»
−85
Новая страница: «Connect the control contactor coil through the relay extension module (see. Figure).»
−73
Новая страница: «Use the extension module with relay outputs, egSpecial:MyLanguage/Модули ввода-вывода#Модуль релейных выходов (WBIO-DO-R3A…»
−67
Новая страница: «== Contactors with a 110/250V control voltage ==»
−33
Новая страница: «* It can be connected to Rx inputs controller, activating the inside current.»
−68
Новая страница: «* Using extension module WBE-DI-DR-3 (3 channels). The output "open collector" connect to terminal Ox corresponding extens…»
−100
Новая страница: «* Using input-output module WBIO-DI-DR-8 (8 channels), see. IO Modules . The output "open collector" connect to terminal Dx…»
−127
Новая страница: «And a controller '' 'to have a common ground' ''. There are several methods to connect these devices to the controller:»
−104
Новая страница: «== Devices with open collector output ==»
−40
Новая страница: «Some counters have a pulse output to optocoupler, then two wires have the correct polarity - "plus" and "minus". In this case, minus connected to GND, and the "pl…»
−150
Новая страница: «* Can be connected to the inputs Rx controller, including internal current source. One of the wires connected to GND, the second to the Rx controller.»
−98
Новая страница: «* Using extension module WBE-DI-DR-3 (3 channels). One of the wires connected to GND, the second terminal of the Ox in the…»
−82
Новая страница: «* Using input-output module WBIO-DI-DR-8 (8 channels), see. IO Modules . One of the wires connected to GND, the second to te…»
−117
Новая страница: «* With Ax terminal controller. Connect one wire to the power supply 5-24V, the second wire to the terminal Ax.»
−83
Нет описания правки
−18
Новая страница: «Connection Methods to the controller:»
−27
Новая страница: «These devices form a signal by closing suitable for them two wires.»
−66
Новая страница: «thumb|400px|Example of connection a button»
−18
Новая страница: «== Sensors / meters with pulse output / button ==»
−44
Новая страница: «For a more accurate measurement of resistance, as well as to connect Pt100, Pt1000 and for two- and three-wire circuit is a special Wiren Board 5: Extension Mod…»
−168
Новая страница: «Inputs Rx are designed to measure resistance in the range 1-100kOm. Measured resistance is connected between the GND and Rx.»
−105
Новая страница: «== Resistive Sensors ==»
−38
Новая страница: «Also for the connection of current sensors designed special extension module.»
−78
Новая страница: «Special current inputs in the WB absent but it is possible, using a resistor Rx = 100-300Om, the current is converted into a voltage and connect as in the previous.»
−97
Новая страница: «thumb|400px|Example of connection sensor with current output»
−35
Новая страница: «== Sensors with analog current output ==»
−34