Disassembling the controller case/en: различия между версиями
(Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.») |
(Новая страница: «Bend the latch with the rotational movement with a little effort (not to break), while shifting the angle of the lower base to itself, as shown in the figure by t…») |
||
(не показана 61 промежуточная версия 4 участников) | |||
Строка 1: | Строка 1: | ||
<languages/> | <languages/> | ||
[[File:4_latches.png|300px|thumb|left|Four mounting latches]] | |||
[[File:First_latch.png|300px|thumb|right|Open the first latch]] | |||
[[File:Extracting_the_board.png|300px|thumb|left|Remove the controller board from the case]] | |||
[[File:Bottom_cover_with_cavity.png|300px|thumb|right|Cavity at the bottom of the body]] | |||
The upper part of the controller body is attached to the base on four plastic latches - two on the left and two on the right side. We begin to open the controller case with a latch marked with number "1" in the figure (we start with the latches in the thick part of the body, because in order to open them, you need to make more effort). Use a plastic spatula or screwdriver with a straight slot (the tip can be wrapped with insulation tape or tape, so as not to scratch the plastic case). | |||
Bend the latch with the rotational movement with a little effort (not to break), while shifting the angle of the lower base to itself, as shown in the figure by the arrows. In the same way, open the symmetrical latch, marked with the number "2". The two remaining latches are easily bent by hands to the left and to the right respectively. The lower part of the case is open. | |||
Далее аккуратно извлекаем плату из корпуса, для чего со стороны разъемов внешних модулей плату слегка приподнимаем, а боковую стенку корпуса тянем на себя. Направления показаны на рисунке. Затем вынимаем плату с небольшим усилием, держа ее за края. | |||
Сборка производится в обратном порядке. Обратите внимание: проточка в нижней части корпуса должна располагаться со стороны разъема SIM-карты. Все защелки должны закрываться со щелчком. | |||
<br /><br /><br /><br /><br /><br /><br /><br /><br /><br /> | |||
< | |||
</ | |||
< | |||
</ |
Версия 19:50, 28 мая 2019
The upper part of the controller body is attached to the base on four plastic latches - two on the left and two on the right side. We begin to open the controller case with a latch marked with number "1" in the figure (we start with the latches in the thick part of the body, because in order to open them, you need to make more effort). Use a plastic spatula or screwdriver with a straight slot (the tip can be wrapped with insulation tape or tape, so as not to scratch the plastic case).
Bend the latch with the rotational movement with a little effort (not to break), while shifting the angle of the lower base to itself, as shown in the figure by the arrows. In the same way, open the symmetrical latch, marked with the number "2". The two remaining latches are easily bent by hands to the left and to the right respectively. The lower part of the case is open.
Далее аккуратно извлекаем плату из корпуса, для чего со стороны разъемов внешних модулей плату слегка приподнимаем, а боковую стенку корпуса тянем на себя. Направления показаны на рисунке. Затем вынимаем плату с небольшим усилием, держа ее за края.
Сборка производится в обратном порядке. Обратите внимание: проточка в нижней части корпуса должна располагаться со стороны разъема SIM-карты. Все защелки должны закрываться со щелчком.