Wiren Board 5: Build an image to download in USB Mass-Storage mode/en: различия между версиями
FuzzyBot (обсуждение | вклад) м (FuzzyBot переименовал страницу Сборка образа для загрузки в режиме USB Mass-Storage/en в Wiren Board 5: Build an image to download in USB Mass-Storage mode/en без оставления перенаправления: Часть переводимой страницы Сборка образа для загрузки в режиме USB Mass-Storage.) |
|||
(не показано 8 промежуточных версий 1 участника) | |||
Строка 10: | Строка 10: | ||
** '''DTB''' - nformation about the periphery required for the kernel to work. Is appended to the end of the '''zImage''', ''CONFIG_ARM_APPENDED_DTB'' option should be enabled in the config | ** '''DTB''' - nformation about the periphery required for the kernel to work. Is appended to the end of the '''zImage''', ''CONFIG_ARM_APPENDED_DTB'' option should be enabled in the config | ||
[https://github.com/contactless/wirenboard/tree/https://github.com/contactless/wirenboard/blob/master/contrib/u-boot/wb5_usbfw.sb | [https://github.com/contactless/wirenboard/tree/https://github.com/contactless/wirenboard/blob/master/contrib/u-boot/wb5_usbfw.sb Скачать готовый bootstream] | ||
== | == Сборка Linux == | ||
* | * Получить исходники ядра из git,'' | ||
<nowiki> | <nowiki> | ||
$ git clone https://github.com/contactless/linux.git | $ git clone https://github.com/contactless/linux.git | ||
$ cd linux | $ cd linux | ||
$ git checkout dev/v4.1.15 </nowiki> | $ git checkout dev/v4.1.15 </nowiki> | ||
* | * Скачать initramfs из [https://github.com/contactless/wirenboard/tree/master/initramfs_usbgadget репозитория] и распаковать | ||
<nowiki> | <nowiki> | ||
$ unzip initramfs_usbgadget.zip | $ unzip initramfs_usbgadget.zip | ||
$ sudo tar xvf initramfs_usbgadget.tar</nowiki> | $ sudo tar xvf initramfs_usbgadget.tar</nowiki> | ||
* | * Инициализировать окружение для сборки ядра. При необходимости, изменить в этом файле переменные ''DT'' и ''CROSS_COMPILE'' | ||
<nowiki> | <nowiki> | ||
$ . ./scripts/kbuild-env.sh | $ . ./scripts/kbuild-env.sh | ||
$ set +e</nowiki> | $ set +e</nowiki> | ||
* | * Задать конфиг ядра | ||
<nowiki>$ make mxs_usbgadget_defconfig</nowiki> | <nowiki>$ make mxs_usbgadget_defconfig</nowiki> | ||
* | * Собрать ядро и модули, установив их в распакованную initramfs | ||
<nowiki>$ INSTALL_MOD_PATH=./initramfs_usbgadget/ ./scripts/kbuild.sh</nowiki> | <nowiki>$ INSTALL_MOD_PATH=./initramfs_usbgadget/ ./scripts/kbuild.sh</nowiki> | ||
* | * Собрать ядро с appended DTB и initramfs | ||
<nowiki>$ ./scripts/kbuild-dtb.sh</nowiki> | <nowiki>$ ./scripts/kbuild-dtb.sh</nowiki> | ||
== | == Сборка U-Boot == | ||
* | * Получить исходники U-Boot из git. Нужна ветка ''wb_v2015.07'' | ||
<nowiki> | <nowiki> | ||
$ cd .. | $ cd .. | ||
Строка 44: | Строка 44: | ||
$ cd u-boot | $ cd u-boot | ||
$ git checkout wb_v2015.07</nowiki> | $ git checkout wb_v2015.07</nowiki> | ||
* | * Задать конфиг U-Boot | ||
<nowiki>$ make mx28_wirenboard5_usbgadget_defconfig</nowiki> | <nowiki>$ make mx28_wirenboard5_usbgadget_defconfig</nowiki> | ||
* | * Скопировать ранее собранный образ '''[[Special:MyLanguage/kernel+initramfs]+DTB]''' в директорию U-Boot | ||
$ cp ../linux/zImage-imx28-evk ./zImage | $ cp ../linux/zImage-imx28-evk ./zImage | ||
* | * Собрать совмещенный образ '''[U-Boot+[[kernel+initramfs]+DTB|kernel+initramfs]+DTB]''' в директорию U-Boot | ||
$ cp ../linux/zImage-imx28-evk ./zImage | $ cp ../linux/zImage-imx28-evk ./zImage | ||
* | * Собрать совмещенный образ '''[U-Boot+[[kernel+initramfs]+DTB]]''', пригодный для загрузки по USB (bootstream) | ||
<nowiki>$ CROSS_COMPILE='arm-linux-gnueabi-' make -j4 u-boot.sb</nowiki> | <nowiki>$ CROSS_COMPILE='arm-linux-gnueabi-' make -j4 u-boot.sb</nowiki> | ||
== | == Сборка mxsldr == | ||
Эта утилита нужна для загрузки полученного образа по USB. | |||
Требуется установленная библиотека ''libusb-1.0'' (<nowiki>apt-get install libusb-1.0-0-dev</nowiki>) | |||
<nowiki> | <nowiki> | ||
Строка 65: | Строка 66: | ||
== | == Загрузка собранного образа с помощью mxsldr == | ||
<nowiki>$ ./mxsldr ../u-boot/u-boot.sb</nowiki> | <nowiki>$ ./mxsldr ../u-boot/u-boot.sb</nowiki> |
Версия 19:25, 31 мая 2019
This manual describes how to build bootstream to boot Linux from USB Mass Storage Gadget. In this case, the contents of the SD-card becomes available via USB as a normal USB flash drive.
The structure of the bootstream:
- U-Boot SPL - primary boot loader performs initial initialization
- U-Boot - the boot loader itself, runs Linux
- The Linux kernel image consists of several parts
- zImage - kernel
- initramfs - file system with modules to support USB gadget, is included in zImage
- DTB - nformation about the periphery required for the kernel to work. Is appended to the end of the zImage, CONFIG_ARM_APPENDED_DTB option should be enabled in the config
Сборка Linux
- Получить исходники ядра из git,
$ git clone https://github.com/contactless/linux.git $ cd linux $ git checkout dev/v4.1.15
- Скачать initramfs из репозитория и распаковать
$ unzip initramfs_usbgadget.zip $ sudo tar xvf initramfs_usbgadget.tar
- Инициализировать окружение для сборки ядра. При необходимости, изменить в этом файле переменные DT и CROSS_COMPILE
$ . ./scripts/kbuild-env.sh $ set +e
- Задать конфиг ядра
$ make mxs_usbgadget_defconfig
- Собрать ядро и модули, установив их в распакованную initramfs
$ INSTALL_MOD_PATH=./initramfs_usbgadget/ ./scripts/kbuild.sh
- Собрать ядро с appended DTB и initramfs
$ ./scripts/kbuild-dtb.sh
Сборка U-Boot
- Получить исходники U-Boot из git. Нужна ветка wb_v2015.07
$ cd .. $ git clone https://github.com/contactless/u-boot.git $ cd u-boot $ git checkout wb_v2015.07
- Задать конфиг U-Boot
$ make mx28_wirenboard5_usbgadget_defconfig
- Скопировать ранее собранный образ [[Special:MyLanguage/kernel+initramfs]+DTB] в директорию U-Boot
$ cp ../linux/zImage-imx28-evk ./zImage
- Собрать совмещенный образ [U-Boot+[[kernel+initramfs]+DTB|kernel+initramfs]+DTB] в директорию U-Boot
$ cp ../linux/zImage-imx28-evk ./zImage
- Собрать совмещенный образ [U-Boot+[[kernel+initramfs]+DTB]], пригодный для загрузки по USB (bootstream)
$ CROSS_COMPILE='arm-linux-gnueabi-' make -j4 u-boot.sb
Сборка mxsldr
Эта утилита нужна для загрузки полученного образа по USB. Требуется установленная библиотека libusb-1.0 (apt-get install libusb-1.0-0-dev)
$ cd .. $ git clone http://git.denx.de/mxsldr.git $ cd mxsldr $ make
Загрузка собранного образа с помощью mxsldr
$ ./mxsldr ../u-boot/u-boot.sb