Модуль выходов "сухой контакт" (оптореле) WBE-DO-SSR-2/en: различия между версиями
(Новая страница: «The relay control signals are on the RX (K1) and IRQ (K2) contact of the extension module») |
(Новая страница: «Select "WBE-DO-OR-2: Dual Solid-State Signal Relay Module" in the Internal slot 1 or 2 section (depending on the slot number) and click Save.») |
||
(не показано 5 промежуточных версий этого же участника) | |||
Строка 67: | Строка 67: | ||
Select "WBE-DO-OR-2: Dual Solid-State Signal Relay Module" in the Internal slot 1 or 2 section (depending on the slot number) and click Save. | Select "WBE-DO-OR-2: Dual Solid-State Signal Relay Module" in the Internal slot 1 or 2 section (depending on the slot number) and click Save. | ||
После добавления два дополнительных выхода появляется в Devices рядом с выходами контроллера (раздел Discrete I/O). | |||
При добавлении устройство определяется сразу же, перезагрузка не требуется. | |||
[[Файл:OptoRelay.jpg|thumb| WBE-DO-OR-2 | [[Файл:OptoRelay.jpg|thumb|Модуль выходов "сухой контакт" (оптореле) WBE-DO-OR-2 для Wiren Board 5 | ||
]] | ]] | ||
==MQTT == | == MQTT == | ||
{| class="wikitable" | {| class="wikitable" | ||
! | !Слот | ||
! | !Клемма | ||
! | !Выход реле | ||
! | !Канал (MQTT) | ||
! | !Топик (MQTT) | ||
|- | |- | ||
| rowspan="2" |MOD1 | | rowspan="2" |MOD1 | ||
Строка 107: | Строка 107: | ||
== | == Технические детали == | ||
Сигналы управления реле находятся на контакте RX (K1) и IRQ (K2) модуля расширения |
Версия 19:26, 1 июля 2019
The module is designed to control the inputs of the "dry contact" type in applications where galvanic isolation is required.
Technical specifications
The module contains two SPST (normally open) configuration optocouplers with one common contact.
Each channel has built-in protection against voltage surges when switching inductive load (TVS at 40V).
Parameter | Value |
---|---|
Number of outputs | 2 |
Outputs type | opto relay |
Contacts configuration | SPST (normally open) |
Maximum switching voltage | 40V AC/DC |
Maximum switching current, per channel | 100 mA |
The channel resistance in the open state | < 5 Оhm |
Voltage isolation between the controller and the output | 1500 Vrms |
Maximum power consumption | 0.05 Вт |
Compatibility | Compatiblу with Wiren Board 5 of all revisions. |
Pinout
Terminal | Function |
---|---|
O1 | K1 |
O2 | K2 |
O3 | COM |
Configuration
Configuration is carried out in the web interface, section Configs => Hardware Modules Configuration.
Select "WBE-DO-OR-2: Dual Solid-State Signal Relay Module" in the Internal slot 1 or 2 section (depending on the slot number) and click Save.
После добавления два дополнительных выхода появляется в Devices рядом с выходами контроллера (раздел Discrete I/O).
При добавлении устройство определяется сразу же, перезагрузка не требуется.
MQTT
Слот | Клемма | Выход реле | Канал (MQTT) | Топик (MQTT) |
---|---|---|---|---|
MOD1 | O1 | K1 | wb-gpio/MOD1_K1 | /devices/wb-gpio/controls/MOD1_K1 |
O2 | K2 | wb-gpio/MOD1_K2 | /devices/wb-gpio/controls/MOD1_K2 | |
MOD2 | O1 | K1 | wb-gpio/MOD2_K1 | /devices/wb-gpio/controls/MOD2_K1 |
O2 | K2 | wb-gpio/MOD2_K2 | /devices/wb-gpio/controls/MOD2_K2 |
Технические детали
Сигналы управления реле находятся на контакте RX (K1) и IRQ (K2) модуля расширения