12 063
правки
Модуль выходов "сухой контакт" (оптореле) WBE-DO-SSR-2/en: различия между версиями
Модуль выходов "сухой контакт" (оптореле) WBE-DO-SSR-2/en (просмотреть исходный код)
Версия 19:27, 1 июля 2019
, 4 года назадНовая страница: «The relay control signals are on the RX (K1) and IRQ (K2) contact of the extension module»
(Новая страница: «Each channel has built-in protection against voltage surges when switching inductive load (TVS at 40V).») |
(Новая страница: «The relay control signals are on the RX (K1) and IRQ (K2) contact of the extension module») |
||
| (не показано 11 промежуточных версий этого же участника) | |||
| Строка 9: | Строка 9: | ||
Each channel has built-in protection against voltage surges when switching inductive load (TVS at 40V). | Each channel has built-in protection against voltage surges when switching inductive load (TVS at 40V). | ||
{| class="wikitable" | {| class="wikitable" style="text-align:center" | ||
! | !Parameter | ||
! | !Value | ||
|- | |- | ||
| | |Number of outputs | ||
|2 | |2 | ||
|- | |- | ||
| | |Outputs type | ||
| | |opto relay | ||
|- | |- | ||
| | |Contacts configuration | ||
|SPST ( | |SPST (normally open) | ||
|- | |- | ||
| | |Maximum switching voltage | ||
|40V AC/DC | |40V AC/DC | ||
|- | |- | ||
| | |Maximum switching current, per channel | ||
|'''100 mA''' | |'''100 mA''' | ||
|- | |- | ||
| | |The channel resistance in the open state | ||
|< 5 | |< 5 Оhm | ||
|- | |- | ||
| | |Voltage isolation between the controller and the output | ||
| | |1500 Vrms | ||
|- | |- | ||
| | |Maximum power consumption | ||
|0.05 Вт | |0.05 Вт | ||
|- | |- | ||
| | |Compatibility | ||
| | |Compatiblу with [[Wiren Board 5/en|Wiren Board 5]] of all revisions. | ||
|} | |} | ||
== | == Pinout == | ||
{| class="wikitable" | {| class="wikitable" | ||
! | !Terminal | ||
! | !Function | ||
|- | |- | ||
|O1 | |O1 | ||
| Строка 62: | Строка 61: | ||
== | ==Configuration== | ||
Configuration is carried out in the web interface, section Configs => Hardware Modules Configuration. | |||
Select "WBE-DO-OR-2: Dual Solid-State Signal Relay Module" in the Internal slot 1 or 2 section (depending on the slot number) and click Save. | |||
Once added, two additional outputs appear in the Devices next to the controller outputs (the Discrete I/O section). | |||
When adding a device is detected immediately, a reboot is not required. | |||
[[Файл:OptoRelay.jpg|thumb| | [[Файл:OptoRelay.jpg|thumb| WBE-DO-OR-2 for Wiren Board 5 | ||
]] | ]] | ||
== MQTT == | ==MQTT == | ||
{| class="wikitable" | {| class="wikitable" | ||
! | !Slot | ||
! | !Terminal | ||
! | !Output | ||
! | !Channel (MQTT) | ||
! | !Topic (MQTT) | ||
|- | |- | ||
| rowspan="2" |MOD1 | | rowspan="2" |MOD1 | ||
| Строка 108: | Строка 107: | ||
== | ==Technical detail== | ||
The relay control signals are on the RX (K1) and IRQ (K2) contact of the extension module | |||