Первое включение Wiren Board Smart Home/en: различия между версиями
Matveevrj (обсуждение | вклад) Метки: правка с мобильного устройства правка из мобильной версии |
(Новая страница: «==See also== Wiren Board Software») |
||
(не показано 7 промежуточных версий этого же участника) | |||
Строка 5: | Строка 5: | ||
== Preparing to power on == | == Preparing to power on == | ||
Before | Before work | ||
#Be sure to | #Be sure to insert the software image microSD card (included) into the device. | ||
#Install a | #Install a micro SIM card (if you plan to use a GSM module). | ||
#Check the position | #Check the switch position. | ||
==microSD card== | #Connect the power supply. | ||
Installed in the memory card | === microSD card === | ||
===Micro-SIM card=== | Installed in the connector for memory card ('''top''') contacts '''up'''. | ||
=== Micro-SIM card === | |||
===Switch position=== | It is installed in the connector for Micro-SIM card ("lower") contacts '''down''' cut corner inside. | ||
The pressed side with a dot is | === Switch position === | ||
Power supply | The pressed side with a dot is 'off'. | ||
There are three types: standard, DIN rail, PoE injector. | === Power supply === | ||
There are three types: standard, DIN-rail, PoE-injector. | |||
The standard power supply is connected to the | '''Do not connect two different power supplies at the same time''', it will burn them and the controller. | ||
The DIN rail | The standard power supply is connected to the appropriate connector. | ||
Passive PoE power supply is connected Ethernet cable. | The power supply on a DIN rail connect the wires to the big terminals Vin and Gnd (next to the relays, see diagram http://contactless.ru/wiki/index.php/%D0%A4%D0%B0%D0%B9%D0%BB:WB3.5.png) | ||
The Passive PoE power supply is connected by an Ethernet cable. | |||
=== Antenna connection === | === Antenna connection === | ||
Строка 44: | Строка 45: | ||
== Software Update == | == Software Update == | ||
We recommend you to upgrade your software. See | We recommend you to upgrade your software. See [http://contactless.ru/forums/topic/%D0%BE%D0%B1%D0%BD%D0%BE%D0%B2%D0%BB%D0%B5%D0%BD%D0%B8%D1%8F-%D0%BF%D0%BE/] | ||
==See also== | ==See also== | ||
[[Программное обеспечение Wiren Board/en| Wiren Board Software]] | [[Программное обеспечение Wiren Board/en| Wiren Board Software]] |
Версия 13:06, 19 июля 2019
"'This article is relevant for wiren Board 3.5"' [Problem with memory cards in the first batch of devices]
Preparing to power on
Before work
- Be sure to insert the software image microSD card (included) into the device.
- Install a micro SIM card (if you plan to use a GSM module).
- Check the switch position.
- Connect the power supply.
microSD card
Installed in the connector for memory card (top) contacts up.
Micro-SIM card
It is installed in the connector for Micro-SIM card ("lower") contacts down cut corner inside.
Switch position
The pressed side with a dot is 'off'.
Power supply
There are three types: standard, DIN-rail, PoE-injector. Do not connect two different power supplies at the same time, it will burn them and the controller. The standard power supply is connected to the appropriate connector. The power supply on a DIN rail connect the wires to the big terminals Vin and Gnd (next to the relays, see diagram http://contactless.ru/wiki/index.php/%D0%A4%D0%B0%D0%B9%D0%BB:WB3.5.png) The Passive PoE power supply is connected by an Ethernet cable.
Antenna connection
As standard, the controller comes with a connected internal Wi-Fi antenna, radio 433 and an external GSM antenna on the SMA connector (in the first batch were supplied with an internal GSM antenna).
To connect an external antenna, use the adapter with u.fl to SMA. The location of u.fl GSM and Wi-Fi connectors is shown on the description page.
U.fl connector for external 433MHz antenna is located next to the base of the pin antenna, when connecting an external, unsolder/bite off the internal pin antenna.
If the cellular signal is weak, the controller may be unstable with the internal GSM antenna. Use externally and place it away from the controller.
First time start
The first switch-on of the device may take a long time (3-4 minutes). The first time you turn it on, SSH secret keys are generated and the serial number of the device is initialized.
IP-address
When connected via Ethernet, the Wiren Board Smart Home controller automatically receives an IP address via DHCP. You can find the IP address that the device received in the list of connected clients in the administrative interface of your router.
SSH access and console
Standard username and password: user: root, password wirenboard
Software Update
We recommend you to upgrade your software. See [1]