Wiren Board 4:Аппаратная часть/en: различия между версиями
(Новая страница: «=== Resistive output sensors ===») |
|||
(не показано 28 промежуточных версий 4 участников) | |||
Строка 30: | Строка 30: | ||
|| [[Special:MyLanguage/GSM/GPRS|GSM/GPRS]] || 900/1800 МГц. GPRS multi-slot class 10/8 max. 85.6 kbps (downlink). microSIM card, packaged | || [[Special:MyLanguage/GSM/GPRS|GSM/GPRS]] || 900/1800 МГц. GPRS multi-slot class 10/8 max. 85.6 kbps (downlink). microSIM card, packaged | ||
|- | |- | ||
|| Radio module 433 MHz || RFM69H module. To communicate with [[Special:MyLanguage/Поддерживаемые устройства |Noolite]] devices, [[Special:MyLanguage/Поддерживаемые устройства |Oregon]] sensors | || Radio module 433 MHz || RFM69H module. To communicate with [[Special:MyLanguage/Поддерживаемые устройства |Noolite]] devices, [[Special:MyLanguage/Поддерживаемые устройства |Oregon]] NRF24L01 sensors | ||
|- | |- | ||
|| Radio module 2.4 GHz || [[Special:MyLanguage/NRF24L01|NRF24L01]]To communicate with similar NRF24 modules ''(optional)'' | || Radio module 2.4 GHz || [[Special:MyLanguage/NRF24L01|NRF24L01]]To communicate with similar NRF24 modules ''(optional)'' | ||
Строка 40: | Строка 40: | ||
| Ethernet || 10/100 Mbit/s, RJ-45 connector | | Ethernet || 10/100 Mbit/s, RJ-45 connector | ||
|- | |- | ||
|| USB 2.0 Host || 2 connectors (one connector is located inside the | || USB 2.0 Host || 2 connectors (one connector is located inside the housing) | ||
|- | |- | ||
|| [[Special:MyLanguage/Аудиовыход|Audiooutput]] || 3.5 mm connector, stereo | || [[Special:MyLanguage/Аудиовыход|Audiooutput]] || 3.5 mm connector, stereo | ||
Строка 52: | Строка 52: | ||
!colspan="2"| '''Connection of sensors''' | !colspan="2"| '''Connection of sensors''' | ||
|- | |- | ||
| 5x[[Special:MyLanguage/ADC| | | 5x[[Special:MyLanguage/ADC | АЦП]] || 2x up to 24V , 3x - up to 5V | ||
|- | |- | ||
||2x[[Special:MyLanguage/Входы для резистивных датчиков|Inputs for resistive sensors]] | ||2x[[Special:MyLanguage/Входы для резистивных датчиков|Inputs for resistive sensors]] | ||
Строка 67: | Строка 67: | ||
| 9x[[Special:MyLanguage/Управление низковольтной нагрузкой|"Open collector"]] || 24V/2A, control of contactors, LED strip lights, etc. | | 9x[[Special:MyLanguage/Управление низковольтной нагрузкой|"Open collector"]] || 24V/2A, control of contactors, LED strip lights, etc. | ||
|- | |- | ||
|| 2xРеле || Up to 250V/3A, normally | || 2xРеле || Up to 250V/3A, normally closed contacts | ||
|- | |- | ||
Строка 76: | Строка 76: | ||
||1x[[Special:MyLanguage/Buzzer|Speaker]]|| "buzzer" | ||1x[[Special:MyLanguage/Buzzer|Speaker]]|| "buzzer" | ||
|- | |- | ||
|| Real-time clock RTC || [[Special:MyLanguage/RTC|RTC]] | || Real-time clock RTC || [[Special:MyLanguage/RTC|RTC]] Redundant battery | ||
|- | |- | ||
|| Watchdog timer || Separate hardware watchdog to perform full reset of the device | || Watchdog timer || Separate hardware watchdog to perform full reset of the device | ||
Строка 94: | Строка 94: | ||
|| Overall dimensions || board - 103x87x20 mm, housing for DIN rail installation 6U | || Overall dimensions || board - 103x87x20 mm, housing for DIN rail installation 6U | ||
|- | |- | ||
||Operation || Operating temperature - 0..70C (-40..85C by request) | ||Operation || Operating temperature - 0..70C (-40..85C by request) Varnish coating for moister protection | ||
|- | |- | ||
{|} | {|} | ||
Строка 104: | Строка 104: | ||
[[File:Схемки защиты WB4-2.png|thumb|400px|Input and output protection scheme]] | [[File:Схемки защиты WB4-2.png|thumb|400px|Input and output protection scheme]] | ||
Some terminal blocks can be used to perform | Some terminal blocks can be used to perform several functions. Ref. description of inputs and outputs and [[Special:MyLanguage/Мультиплексирование портов| Port multiplexing]] article. | ||
{| border="1" width="45%" class="wikitable" style="text-align:center" | {| border="1" width="45%" class="wikitable" style="text-align:center" | ||
Строка 125: | Строка 125: | ||
| '''O3''' | | '''O3''' | ||
|- | |- | ||
| '''A''' || 30 V || 0V ||rowspan="2" | | | '''A''' || 30 V || 0V ||rowspan="2" |Uninsulated port [[Special:MyLanguage/RS-485|RS-485]] | ||
|- | |- | ||
| '''B''' || 30 V || +5V | | '''B''' || 30 V || +5V | ||
|- | |- | ||
| '''(9-24)V_OUT''' || 24V || ||Input voltage (output) to power devices | | '''(9-24)V_OUT''' || 24V || ||Input voltage (output) to power devices via RS-485 bus | ||
|- | |- | ||
| '''GND''' ||| || || | | '''GND''' ||| || || | ||
|- | |- | ||
| '''A-iso''' || 30 V || 0V || rowspan="2" | | | '''A-iso''' || 30 V || 0V || rowspan="2" |Optic isolated RS-485 [[Special:MyLanguage/RS-485|RS-485]] | ||
|- | |- | ||
| '''B-iso''' || 30 V || +5V | | '''B-iso''' || 30 V || +5V | ||
|- | |- | ||
| '''GND-iso''' || || || | | '''GND-iso''' || || || Grounding of optic isolated RS-485 | ||
|-} | |-} | ||
Строка 186: | Строка 186: | ||
{|} | {|} | ||
== Input protection == | |||
As compared to version 3, input protection and general noise protection are significantly improved. | |||
#Protection of all inputs from power supply voltage (up to 24 V) and pulse noise. | |||
#Protection from reverse polarity. | |||
#One optic isolated RS-485 port. | |||
#Diode protection of keys at Ax and Dx inputs from inductive loads. | |||
#Protection from relay contact sparking. | |||
== Versatile inputs/outputs Ax and Dx == | |||
[[File:Ax.png|thumb|400px| Equivalent channels A1-A3 scheme]] | |||
[[File:А5.png|thumb|400px|Equivalent channels A4-A5 scheme]] | |||
[[File:Dx.png|thumb|400px|Equivalent channels Dx scheme]] | |||
Versatile channels consist of input and output stages that operate simultaneously, as well as protective diodes (connected to one terminal of the channel). | |||
Output stage consists of the Tx switching element. | |||
Tx key grounds the outputs. | |||
Under control of the controller logical boards, the Tx key may be one of 2 states: | |||
*Active (closed); 0 is at the channel output. | |||
*Inactive (open), high impedance. Such outputs are called “open collectors”. | |||
Input stage of Ax channel consists of an analogue-to-digital converter ADCx and an input resistor Rx. Input resistance of the ADCx is high. It is always ON and does not affect the channel operation as it works in output mode. In input mode the Tx key is inactive (open) and, thus, does not affect voltage measuring at the channel terminals. Input resistance of the channel in input mode is formed by the Rx resistor. If no other circuits are connected to the channel terminals, the resistor downs the input voltage to zero, and the ADCx converter will read 0. | |||
In input mode the Tx | |||
If the channel | |||
А4 and А5 support binary input function DI: more than 3V at the terminal is considered as triggering of the input. | А4 and А5 support binary input function DI: more than 3V at the terminal is considered as triggering of the input. | ||
Строка 250: | Строка 243: | ||
== Power Supply == | === Power Supply === | ||
[[File:Питание версии4.png|thumb|300px|Блок-схема питания WB 4]] | [[File:Питание версии4.png|thumb|300px|Блок-схема питания WB 4]] | ||
Строка 260: | Строка 253: | ||
Allowed voltage range is 7-24 V. | Allowed voltage range is 7-24 V. | ||
Average power consumption of the board is 1.5-2 W, but the GSM module may temporally consume | Average power consumption of the board is 1.5-2 W, but the GSM module may temporally consume as much as 8 W. Therefore, it is recommended to use at least 10 W power sources. | ||
A standard connector jack 5.5x2.1 mm is provided for connection to the power source. Input power can also be connected to Vin and GND terminals. | A standard connector jack 5.5x2.1 mm is provided for connection to the power source. Input power can also be connected to Vin and GND terminals. | ||
Строка 351: | Строка 344: | ||
=== Resistive output sensors === | === Resistive output sensors === | ||
Входы R1 R2 предназначены для измерения сопротивлений в диапазоне 1-100кОм. | |||
Измеряемое сопротивление подключается между GND и Rx. | |||
=== | === Датчики/счетчики с импульсными выходами/кнопки === | ||
Такие устройства формируют сигнал, замыкая подходящие к ним два провода. | |||
Подключите один провод к клемме GND, или соедините с общей земляной шиной. | |||
Второй провод подключите к клемме Dx. | |||
Некоторые счетчики имеют импульсный выход на оптроне, тогда два провода имеют полярность - "плюс" и "минус". | |||
В таком случае минус подключается к GND, "плюс" к Dx. | |||
=== | === Устройства с выходом открытый коллектор === | ||
Устройство и контроллер должны иметь общую землю. | |||
Выход "открытый коллектор" подключите к клемме Dx. | |||
Строка 384: | Строка 378: | ||
=== RS-485 | === Подключение к сети RS-485 === | ||
See [[Special:MyLanguage/RS-485|RS-485]]. | See [[Special:MyLanguage/RS-485|RS-485]]. | ||
Строка 397: | Строка 391: | ||
=== Example of device connection === | === Example of device connection === | ||
Test bench diagram - [[Special:MyLanguage/Файл:Стенд-hi.jpg|thumb|500px|Test bench diagram]] | |||
== | == Diagram and Drawing == | ||
Wiren Board 4 principle diagram - [[Файл:WB 4.3.pdf|Файл:WB 4.3.pdf]], scheme - [[Файл:WB 4.2 чертеж.pdf|Файл:WB 4.2 чертеж.pdf]] | Wiren Board 4 principle diagram - [[Файл:WB 4.3.pdf|Файл:WB 4.3.pdf]], scheme - [[Файл:WB 4.2 чертеж.pdf|Файл:WB 4.2 чертеж.pdf]] |
Версия 15:58, 17 июля 2015
Technical specifications
Software | |
---|---|
Operating System | Debian Linux 7.0. Mainline kernel 3.19. |
Controller | |
CPU | Freescale i.MX233 454 MHz |
RAM | DDR SDRAM 64 MB |
ROM | MicroSD card 32 GB max |
Wireless Interfaces | |
Wi-Fi | 802.11 b/g/n 2.4 ГГц |
GSM/GPRS | 900/1800 МГц. GPRS multi-slot class 10/8 max. 85.6 kbps (downlink). microSIM card, packaged |
Radio module 433 MHz | RFM69H module. To communicate with Noolite devices, Oregon NRF24L01 sensors |
Radio module 2.4 GHz | NRF24L01To communicate with similar NRF24 modules (optional) |
Wired interfaces | |
Ethernet | 10/100 Mbit/s, RJ-45 connector |
USB 2.0 Host | 2 connectors (one connector is located inside the housing) |
Audiooutput | 3.5 mm connector, stereo |
2xRS-485 (one of the ports is insulated) | Software support of Modbus RTU, ADICON/A-BUS/Uniel, and Smartbus G4 protocols |
Debug console | Debug UART To be connected via USB-UART adapter |
2x 1-Wire | Connection of temperature and moister sensors |
Connection of sensors | |
5x АЦП | 2x up to 24V , 3x - up to 5V |
2xInputs for resistive sensors | Connection of 10 kOhm thermistors. The controller can be used as ADC up to 3.3V |
4x"Dry contact" | Connection of pushbuttons, gerkons, counters with pulse outputs |
2x DI (digital input) | |
Outputs | |
9x"Open collector" | 24V/2A, control of contactors, LED strip lights, etc. |
2xРеле | Up to 250V/3A, normally closed contacts |
Other | |
8xGPIO | are multiplexed with other inputs/outputs |
1xSpeaker | "buzzer" |
Real-time clock RTC | RTC Redundant battery |
Watchdog timer | Separate hardware watchdog to perform full reset of the device |
1x Connector for extension module | Supported extension modules: * RS-232 extension module |
Power supply | |
Operating voltage | 9-24 V |
Power consumption | <3 W (maximum 12 W) |
Redundant battery | Operation Li-ion batteries are supported |
Passive Power over Ethernet | Passsive Power over Ethernet |
Overall dimensions | board - 103x87x20 mm, housing for DIN rail installation 6U |
Operation | Operating temperature - 0..70C (-40..85C by request) Varnish coating for moister protection |
Terminal blocks
Some terminal blocks can be used to perform several functions. Ref. description of inputs and outputs and Port multiplexing article.
legend |
Max. V, I | state default | Functions | ||||
Upper row, right block | |||||||
---|---|---|---|---|---|---|---|
Vin | 24V | Input voltage | |||||
GND | |||||||
O1 | Inputs/outputs of extension module | ||||||
O2 | |||||||
O3 | |||||||
A | 30 V | 0V | Uninsulated port RS-485 | ||||
B | 30 V | +5V | |||||
(9-24)V_OUT | 24V | Input voltage (output) to power devices via RS-485 bus | |||||
GND | |||||||
A-iso | 30 V | 0V | Optic isolated RS-485 RS-485 | ||||
B-iso | 30 V | +5V | |||||
GND-iso | Grounding of optic isolated RS-485 | ||||||
Lower row, left block | |||||||
5V out | 5V, 0.5A | 5V | output 5V (for 1-Wire sensors) | ||||
W1 | 30V | 3.3V | 1-Wire, GPIO | ||||
W2 | |||||||
R1 | 5V | High Z | Resistive sensors,ADC, digital inputs (GPIO) without retightening | ||||
R2 | |||||||
A1 | Vin , 2A | High Z | "Open collector" outputs, ADC | ||||
A2 | |||||||
A3 | |||||||
A4 | Vin , 2A | High Z | "Open collector" outputs, ADC , digital inputs DI | ||||
A5 | |||||||
GND | |||||||
Lower row, right block | |||||||
GND | |||||||
GND | |||||||
D1 | Vin , 2A | +5V | "Open collector" outputs, "dry contact" inputs | ||||
D2 | |||||||
D3 | |||||||
D4 | |||||||
Relay1 | 250, 2A | is open | first relay | ||||
Relay2 | second relay |
Input protection
As compared to version 3, input protection and general noise protection are significantly improved.
- Protection of all inputs from power supply voltage (up to 24 V) and pulse noise.
- Protection from reverse polarity.
- One optic isolated RS-485 port.
- Diode protection of keys at Ax and Dx inputs from inductive loads.
- Protection from relay contact sparking.
Versatile inputs/outputs Ax and Dx
Versatile channels consist of input and output stages that operate simultaneously, as well as protective diodes (connected to one terminal of the channel).
Output stage consists of the Tx switching element. Tx key grounds the outputs. Under control of the controller logical boards, the Tx key may be one of 2 states:
- Active (closed); 0 is at the channel output.
- Inactive (open), high impedance. Such outputs are called “open collectors”.
Input stage of Ax channel consists of an analogue-to-digital converter ADCx and an input resistor Rx. Input resistance of the ADCx is high. It is always ON and does not affect the channel operation as it works in output mode. In input mode the Tx key is inactive (open) and, thus, does not affect voltage measuring at the channel terminals. Input resistance of the channel in input mode is formed by the Rx resistor. If no other circuits are connected to the channel terminals, the resistor downs the input voltage to zero, and the ADCx converter will read 0.
А4 and А5 support binary input function DI: more than 3V at the terminal is considered as triggering of the input.
Input stage of Dx channels consists of a circuit for connection of dry contacts. This stage continuously provides 5V voltage at the terminal. In input mode the Tx key is inactive (open). When the terminal is grounded, small current (2 mA) flows via the channel. Controller considers that as triggering of the input. Closing of the Tx key is considered as triggering of the input. In output mode the output stage does not affect the channel operation, provided that a more than 5 V load is connected to the channel.
Resistive Inputs
Each terminal is connected to internal adjustable current source. The controller measures current flowing through the sensor and simultaneously measures the terminal voltage to calculate the resistance value. If necessary and if the corresponding program is available, resistive inputs may be used as additional analogue/binary ones.
Extension modules
Ref. the corresponding articles to describe connection and software operation:
- Wiren Board 4: RS-232 extension module
- Wiren Board 4: CAN extension module
- Wiren Board 4: UART-CAN extension module
Power Supply
External power source
Allowed voltage range is 7-24 V. Average power consumption of the board is 1.5-2 W, but the GSM module may temporally consume as much as 8 W. Therefore, it is recommended to use at least 10 W power sources.
A standard connector jack 5.5x2.1 mm is provided for connection to the power source. Input power can also be connected to Vin and GND terminals.
Power over Ethernet
It is possible to power the device via an Ethernet cable. Ref.Power over Ethernet.
Battery
It is possible to connect Wiren Board to a Li-Ion (Li-Pol) battery with maximal voltage of 4.2 V. When the device is connected to a power source, the battery is charged with up to 0.5 A current.
The battery is provided from charging at negative temperature. However, it is not protected from overcharge, and thus it is strongly recommended to use batteries with internal protection boards.
It is necessary to meet the battery polarity!
Working with WAGO 250 terminal blocks
Self-tightened clips of WAGO 250 Series are used as interface terminals of the controller. When a stripped single-core wire is inserted into a clip, it is automatically caught by a spring latch. In order to insert multi-core wires, it is necessary to press the clip button to compress the spring. The button is provided with a slot suitable for a flat screw-drive. In order to remove the wire, it is necessary to press the clip button to compress the spring, and then pull the wire out of the clip.
Wi-Fi, GSM, 433MHz antennas
Wi-Fi antenna is located inside the casing.
GSM and 433 MHz radio antennas are connected to SMA connectors on the casing.
If GSM signal is weak, it is recommended to use an external antenna and to locate it far from the controller.
Peripheral devices connection diagrams
Low voltage load control
12/24V relays, LEDs, fans, indicator lamps, etc.
Power supply voltage of the controller must not be lower than voltage of the connected load. Connect "+" of the load to "+" of the power source, and "-" to Ax or Dx terminals. If several channels are used, and their total current exceeds 5 A, connect several GND terminals to "-" of the power source. Voltage spikes occur when the device controls an inductive load (relay). In order to protect the controller from overload, it is equipped with built-in protective diodes. No external protective elements are necessary.
Electric contactors with control voltage of 220 V
Connect the control coil of the contactor via WB relay (ref. fig.). The WB relay is equipped with a damping RC-circuit and a TVS. No external components are necessary.
Analogue voltage output sensors
Connect the device ground to the GND terminal or a common grounding bus. Connect the sensor output to Ax or Rx terminal. Ах/Rx channels feature different ranges of measured voltages. Select the optimal channel for your sensor.
Analogue current output sensors
WB is not equipped with special current inputs, but it is possible to convert current to voltage by means of 100-300 Ohm resister and use the connection diagram described above.
Resistive output sensors
Входы R1 R2 предназначены для измерения сопротивлений в диапазоне 1-100кОм. Измеряемое сопротивление подключается между GND и Rx.
Датчики/счетчики с импульсными выходами/кнопки
Такие устройства формируют сигнал, замыкая подходящие к ним два провода. Подключите один провод к клемме GND, или соедините с общей земляной шиной. Второй провод подключите к клемме Dx. Некоторые счетчики имеют импульсный выход на оптроне, тогда два провода имеют полярность - "плюс" и "минус". В таком случае минус подключается к GND, "плюс" к Dx.
Устройства с выходом открытый коллектор
Устройство и контроллер должны иметь общую землю. Выход "открытый коллектор" подключите к клемме Dx.
Network connection of 1-Wire
Connect the device ground to the GND terminal or a common grounding bus. Connect the data line to one of 1-Wire terminals. Connect the power line to 5V terminal (internal power source). It is allowed to use external power sources of 1-Wire bus.
If a passive power source is used, the power terminals of all sensors must be connected to the grounding bus. In such cases the bus will consist of two wires connected to 1-Wire and GND, respectively.
Подключение к сети RS-485
See RS-485.
Wiren Board 4 controllers are equipped with two RS-485 ports. One of them is galvanic insulated, the other one is not. If the RS-485 network is quite large, it is better use the insulated port for connection. Lines A and B are connected to A and B terminals, respectively. The signal ground (if any) must be connected to the GNDiso terminal.
A and B lines are often accompanied by another pair of wires used to power devices connected to the bus. In such cases it is necessary to use GND and Vout terminals. Current in power wires must not exceed 1 A.
Example of device connection
Test bench diagram - thumb|500px|Test bench diagram
Diagram and Drawing
Wiren Board 4 principle diagram - Файл:WB 4.3.pdf, scheme - Файл:WB 4.2 чертеж.pdf