618
правок
Garik (обсуждение | вклад) |
Garik (обсуждение | вклад) |
||
Строка 257: | Строка 257: | ||
|2.1 | |2.1 | ||
|WB-MAP3H, WB-MAP3E, WB-MAP12H, WB-MAP6S | |WB-MAP3H, WB-MAP3E, WB-MAP12H, WB-MAP6S | ||
|* | |* Change: WB-MAPs and CTs are now supposed to be calibrated separately. | ||
Each CT is described by two parameters: (effective) turns ratio and phase delay. | Each CT is described by two parameters: (effective) turns ratio and phase delay. | ||
These parameters are to be programmed into WB-MAP registers to proper operation | These parameters are to be programmed into WB-MAP registers to proper operation | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Change: phase angle is consistent between MAP3E and other models (-180..+180 notation) | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Added: 32-bit registers for voltage and current | ||
|- | |- | ||
|WB-MRGB | |WB-MRGB | ||
Строка 271: | Строка 271: | ||
|WB-MRGBW-D | |WB-MRGBW-D | ||
| | | | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Fix change modbus uart settings | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Change eeprom files to submodule. add neccesory defines. change project paths | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Move eeprom settings load/save to separate file. | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Move eeprom settings struct defines from config.h to settings.c. | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Add modbus id change valdation | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Add validation modbus settings when load from eeprom. | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Add validation for buttons disable, pwm divider and fade time settings | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Disable 1200 baud variant (need research why not work) | ||
|- | |- | ||
|WB-MDM2 | |WB-MDM2 | ||
Строка 298: | Строка 298: | ||
|WB-MSW v.3 | |WB-MSW v.3 | ||
|* Note: MSW v.3 VOC-sensor related fixes and improvenets | |* Note: MSW v.3 VOC-sensor related fixes and improvenets | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Added: input register 106 with current valid SGPC3 baseline reported by the sensor | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Added: input register 107 with current raw signal | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Change: VOC sensor is initialized for 184s after power-on. During this time VOC registers return error value. | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 316: | Строка 316: | ||
WB-M1W2, WB-MAI2-mini/cc | WB-M1W2, WB-MAI2-mini/cc | ||
|* Added: add new target for WB-MSW v3 | |* Added: add new target for WB-MSW v3 | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Added: add PIR movement sensor support | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Added: add SGPC3 air quality sensor support | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Added: add discrete input mode for 1-wire inputs with activation counters | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Added: improve SPL metering on WB-MS | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Change: improved config storage | ||
<nowiki>*</nowiki> | <nowiki>*</nowiki> Fixes: workaround for IR bug | ||
|- | |- | ||
|WB-MS | |WB-MS |
правок