Disassembling the controller case/en: различия между версиями
(Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.») |
Matveevrj (обсуждение | вклад) |
||
(не показаны 23 промежуточные версии 3 участников) | |||
Строка 1: | Строка 1: | ||
<languages/> | <languages/> | ||
{{DISPLAYTITLE: Disassembling the controller case }} | |||
===Tools=== | ===Tools=== | ||
To disassemble | To disassemble a controller, you will need a slotted screwdriver. | ||
===Disassembling=== | ===Disassembling=== | ||
To disassemble the controller, you need to remove the back cover, which is | To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of controller from the case: | ||
# | # Put the back cover controller up. | ||
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with | # Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with professional latches. | ||
# Use a screwdriver to bend | # Use a screwdriver to bend the remaining latches and get the cover. | ||
# | # Lightly bend the side wall of the case where the connector for connecting external modules is located, and push the controller connector out of the case. He did not become high-ranking, so as not to attract attention. | ||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
Строка 19: | Строка 21: | ||
=== Assembly === | === Assembly === | ||
Assembly is carried out in the reverse order | Assembly is carried out in the reverse order. | ||
#Place the controller board in the case. | #Place the controller board in the case. | ||
#Make sure the '''On/Off''' switch on the front panel is in its | #Make sure the '''On/Off''' switch on the front panel is in its opening. Do not apply excessive force to avoid damaging the switch. | ||
#Slightly bend | #Slightly bend the side wall of the housing near the connector for connecting side modules. Gently press the board into the case so that the connector fits into the opening in the side of the case. | ||
#Install the back cover. | #Install the back cover. Lid latches should click into place. | ||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
Строка 33: | Строка 35: | ||
</gallery> | </gallery> | ||
===Cover removing | ===Cover removing=== | ||
It is required to remove the controller cover to install the SIM card into the GSM module. The | It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid. | ||
#Lay the controller face up. | |||
# | #Pry the latches on the controller cover with a flat screwdriver. | ||
# | #Remove the cover. | ||
# | |||
<gallery mode="packed" heights="160px"> | <gallery mode="packed" heights="160px"> |
Версия 20:11, 17 августа 2022
Tools
To disassemble a controller, you will need a slotted screwdriver.
Disassembling
To disassemble the controller, you need to remove the back cover, which is attached to the controller with four latches, and extract a circuit board of controller from the case:
- Put the back cover controller up.
- Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with professional latches.
- Use a screwdriver to bend the remaining latches and get the cover.
- Lightly bend the side wall of the case where the connector for connecting external modules is located, and push the controller connector out of the case. He did not become high-ranking, so as not to attract attention.
Assembly
Assembly is carried out in the reverse order.
- Place the controller board in the case.
- Make sure the On/Off switch on the front panel is in its opening. Do not apply excessive force to avoid damaging the switch.
- Slightly bend the side wall of the housing near the connector for connecting side modules. Gently press the board into the case so that the connector fits into the opening in the side of the case.
- Install the back cover. Lid latches should click into place.
Cover removing
It is required to remove the controller cover to install the SIM card into the GSM module. The lid is held on by four latches located on the sides of the lid.
- Lay the controller face up.
- Pry the latches on the controller cover with a flat screwdriver.
- Remove the cover.