16 343
правки
Matveevrj (обсуждение | вклад) (Новая страница: «'''Step 3'''. Easily bend the side wall near the connector housing for connecting side modules. With a light insertion, press the pulp into the housing so that the connector enters the opening in the side wall of the housing.») |
(Новая страница: «Installing: # Place the controller face up. # Insert the power switch of the controller into the hole on the cover. # Close all latches carefully.») |
||
(не показано 47 промежуточных версий 3 участников) | |||
Строка 4: | Строка 4: | ||
===Disassembling=== | ===Disassembling=== | ||
To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case | To disassemble the controller, you need to remove the back cover, which is held on by four latches, and extract the circuit board of controller from the case: | ||
# Place the controller back cover up. | |||
# Insert a screwdriver between the latch and the foundation. With a smooth twisting motion, release the latch and pull the back cover up. Do the same with all other latches. | |||
# Use a screwdriver to bend back the remaining latches and take off the cover. | |||
# Slightly bend back the side wall of the case where a connector for linking external modules is located, and push the circuit board out of the case. Don’t push too hard, otherwise you will damage the connector and elements to PCB. | |||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
Image: 4_latches.png | | Image: 4_latches.png | Latches | ||
Image: Case2.jpg | | Image: Case2.jpg | Removing the back cover | ||
Image: Case4.jpg | | Image: Case4.jpg | Back cover removed | ||
Image: Case5.jpg | | Image: Case5.jpg | Removing the circuit board | ||
</gallery> | </gallery> | ||
=== Assembly === | === Assembly === | ||
Assembly is carried out in the reverse order | Assembly is carried out in the reverse order: | ||
#Place the controller board in the case. | |||
#Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch. | |||
#Slightly bend back the side wall of the case where the connector for linking external modules is located. Gently press the circuit board into the case so that the connector fits into the aperture in the side of the case. | |||
Make sure the '''On/Off''' switch on the front panel is in its aperture. Do not apply excessive force to avoid damaging the switch. | #Install the back cover. The cover latches should close whith a clicking sound. | ||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
Image: Case6.jpg | | Image: Case6.jpg | Circuit board installation | ||
Image: Case7.jpg | | Image: Case7.jpg | Front panel switch | ||
Image: Case5.jpg | | Image: Case5.jpg | Installing the connector in the aperture | ||
Image: Case8.jpg | | Image: Case8.jpg | Cover installed | ||
</gallery> | </gallery> | ||
=== | ===Cover removing and installing=== | ||
It is required to remove the controller cover to install the SIM card into the GSM module. The cover is attached to the controller with four latches located on the sides of the case. | |||
Removing: | |||
#Place the controller face up. | |||
#Pry the latches on a front cover open with the slotted screwdriver. | |||
#Take off the cover. | |||
Installing: | |||
# Place the controller face up. | |||
# Insert the power switch of the controller into the hole on the cover. | |||
# Close all latches carefully. | |||
<gallery mode="packed" heights="160px"> | <gallery mode="packed" heights="160px"> | ||
Image: Cover_rem1.jpg | | Image: Cover_rem1.jpg | Front cover | ||
Image: Cover_rem2.jpg | | Image: Cover_rem2.jpg | Latches | ||
Image: Cover_rem3.jpg | | Image: Cover_rem3.jpg | Front cover removed | ||
</gallery> | </gallery> |