WB-REF-U-CR Modbus Registers: различия между версиями
Matveevrj (обсуждение | вклад) |
|||
(не показаны 3 промежуточные версии 1 участника) | |||
Строка 10: | Строка 10: | ||
== PJ EASY == | == PJ EASY == | ||
{{Wbincludes: | {{Wbincludes:Carel Modbus Register Table Header}} | ||
| 0x0007 | |||
| style="text-align:right;" | 7 | |||
| discrete | |||
| u16 | |||
| Dig.input | |||
| Digital input status | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0000 | |||
| style="text-align:right;" | 0 | |||
| discrete | |||
| u16 | |||
| Rel. comp. | |||
| Compressor relay status | |||
| | |||
| | |||
| | |||
|- | |||
| 0x000D | |||
| style="text-align:right;" | 13 | |||
| discrete | |||
| u16 | |||
| Rel. defr. | |||
| Defrost relay status | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0008 | |||
| style="text-align:right;" | 8 | |||
| discrete | |||
| u16 | |||
| Rel. fan. | |||
| Fan relay status | |||
| | |||
| | |||
| | |||
|- | |||
| 0x000B | |||
| style="text-align:right;" | 11 | |||
| discrete | |||
| u16 | |||
| Rel.AUX | |||
| Activate AUX command | |||
| | |||
| | |||
| | |||
|- | |||
| 0x001D | |||
| style="text-align:right;" | 29 | |||
| discrete | |||
| u16 | |||
| Defrost | |||
| Defrost status | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0018 | |||
| style="text-align:right;" | 24 | |||
| coil | |||
| u16 | |||
| Defrost | |||
| Activate defrost command | |||
| | |||
| | |||
| | |||
|- | |||
| 0x001B | |||
| style="text-align:right;" | 27 | |||
| discrete | |||
| u16 | |||
| C.C. | |||
| Continuous cycle status | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0014 | |||
| style="text-align:right;" | 20 | |||
| coil | |||
| u16 | |||
| C.C. | |||
| Activation contin. cycle | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0011 | |||
| style="text-align:right;" | 17 | |||
| discrete | |||
| u16 | |||
| s_nRTC | |||
| Set point started by RTC | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0013 | |||
| style="text-align:right;" | 19 | |||
| coil | |||
| u16 | |||
| /5 | |||
| Select C/F | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0016 | |||
| style="text-align:right;" | 22 | |||
| coil | |||
| u16 | |||
| /6 | |||
| Disable decimal point | |||
| | |||
| | |||
| | |||
|- | |||
| 0x001F | |||
| style="text-align:right;" | 31 | |||
| coil | |||
| u16 | |||
| d4 | |||
| Defrost at power-on | |||
| | |||
| | |||
| | |||
|- | |||
| 0x001A | |||
| style="text-align:right;" | 26 | |||
| coil | |||
| u16 | |||
| d6 | |||
| Display lock during defr. | |||
| | |||
| | |||
| | |||
|- | |||
| 0x001E | |||
| style="text-align:right;" | 30 | |||
| coil | |||
| u16 | |||
| d9 | |||
| Def prior over comp prots | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0012 | |||
| style="text-align:right;" | 18 | |||
| coil | |||
| u16 | |||
| dC | |||
| Time base | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0015 | |||
| style="text-align:right;" | 21 | |||
| coil | |||
| u16 | |||
| A8 | |||
| En alarm Ed | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0027 | |||
| style="text-align:right;" | 39 | |||
| coil | |||
| u16 | |||
| F0 | |||
| Enable evap fan control | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0020 | |||
| style="text-align:right;" | 32 | |||
| coil | |||
| u16 | |||
| F2 | |||
| Stop fans if compr stops | |||
| | |||
| | |||
| | |||
|- | |||
| 0x002D | |||
| style="text-align:right;" | 45 | |||
| coil | |||
| u16 | |||
| F3 | |||
| Stop fans during defrost | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0028 | |||
| style="text-align:right;" | 40 | |||
| coil | |||
| u16 | |||
| H4 | |||
| Buzzer inhibition | |||
| | |||
| | |||
| | |||
|- | |||
| 0x002B | |||
| style="text-align:right;" | 43 | |||
| coil | |||
| u16 | |||
| tEn | |||
| Enable RTC | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0024 | |||
| style="text-align:right;" | 36 | |||
| coil | |||
| u16 | |||
| ON/OFF | |||
| Controller ON/OFF command | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0195 | |||
| style="text-align:right;" | 405 | |||
| input | |||
| u16 | |||
| d/ | |||
| Defrost probe value | |||
| °C | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 0 | |||
|- | |||
| 0x0199 | |||
| style="text-align:right;" | 409 | |||
| input | |||
| u16 | |||
| s_pr1 | |||
| Probe 1 status | |||
| °C | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 0 | |||
|- | |||
| 0x0196 | |||
| style="text-align:right;" | 406 | |||
| input | |||
| u16 | |||
| s_pr2 | |||
| Probe 2 status | |||
| °C/°F | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 0 | |||
|- | |||
| 0x0193 | |||
| style="text-align:right;" | 403 | |||
| input | |||
| u16 | |||
| s_pr3 | |||
| Probe 3 status | |||
| °C/°F | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 0 | |||
|- | |||
| 0x019C | |||
| style="text-align:right;" | 412 | |||
| holdng | |||
| u16 | |||
| /C1 | |||
| Probe 1 offset | |||
| °C | |||
| | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x019A | |||
| style="text-align:right;" | 410 | |||
| holdng | |||
| u16 | |||
| /C2 | |||
| Probe 2 offset | |||
| °C/°F | |||
| | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x019E | |||
| style="text-align:right;" | 414 | |||
| holdng | |||
| u16 | |||
| /C3 | |||
| Probe 3 offset | |||
| °C/°F | |||
| | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x019F | |||
| style="text-align:right;" | 415 | |||
| holdng | |||
| u16 | |||
| St | |||
| User set point | |||
| °C | |||
| | |||
| | |||
|- | |||
| 0x0197 | |||
| style="text-align:right;" | 407 | |||
| holdng | |||
| u16 | |||
| rd | |||
| Differential | |||
| °C | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 19 | |||
|- | |||
| 0x019B | |||
| style="text-align:right;" | 411 | |||
| holdng | |||
| u16 | |||
| r1 | |||
| Minimum set point allowed | |||
| °C/°F | |||
| style="text-align:right;" | -50 | |||
| style="text-align:right;" | pk78 | |||
|- | |||
| 0x019D | |||
| style="text-align:right;" | 413 | |||
| holdng | |||
| u16 | |||
| r2 | |||
| Maximum set point allowed | |||
| °C/°F | |||
| style="text-align:right;" | pk79 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x0190 | |||
| style="text-align:right;" | 400 | |||
| holdng | |||
| u16 | |||
| r4 | |||
| Night-time set point diff | |||
| °C/°F | |||
| style="text-align:right;" | -50 | |||
| style="text-align:right;" | 50 | |||
|- | |||
| 0x0198 | |||
| style="text-align:right;" | 408 | |||
| holdng | |||
| u16 | |||
| dt | |||
| End defrost temperature | |||
| °C/°F | |||
| style="text-align:right;" | -50 | |||
| style="text-align:right;" | 127 | |||
|- | |||
| 0x0192 | |||
| style="text-align:right;" | 402 | |||
| holdng | |||
| u16 | |||
| A0 | |||
| Al and fan differential | |||
| °C/°F | |||
| style="text-align:right;" | -20 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x0191 | |||
| style="text-align:right;" | 401 | |||
| holdng | |||
| u16 | |||
| AL | |||
| Low temperature alarm | |||
| °C | |||
| style="text-align:right;" | -50 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x0194 | |||
| style="text-align:right;" | 404 | |||
| holdng | |||
| u16 | |||
| AH | |||
| High temperature alarm | |||
| °C | |||
| style="text-align:right;" | -50 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x01A5 | |||
| style="text-align:right;" | 421 | |||
| holdng | |||
| u16 | |||
| Ac | |||
| Dirty cond Al set point | |||
| °C/°F | |||
| style="text-align:right;" | -50 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x01A9 | |||
| style="text-align:right;" | 425 | |||
| holdng | |||
| u16 | |||
| AE | |||
| Dirty cond Al temp. diff. | |||
| °C/°F | |||
| style="text-align:right;" | 0.1 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x01A6 | |||
| style="text-align:right;" | 422 | |||
| holdng | |||
| u16 | |||
| F1 | |||
| Evap fan control sp | |||
| °C | |||
| style="text-align:right;" | -50 | |||
| style="text-align:right;" | 127 | |||
|- | |||
| 0x01A3 | |||
| style="text-align:right;" | 419 | |||
| holdng | |||
| u16 | |||
| tc_d | |||
| RTC day of the week | |||
| День | |||
| style="text-align:right;" | 1 | |||
| style="text-align:right;" | 7 | |||
|- | |||
| 0x01AC | |||
| style="text-align:right;" | 428 | |||
| holdng | |||
| u16 | |||
| tc_h | |||
| RTC hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01AA | |||
| style="text-align:right;" | 426 | |||
| holdng | |||
| u16 | |||
| tc_m | |||
| RTC minutes | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01AE | |||
| style="text-align:right;" | 430 | |||
| input | |||
| u16 | |||
| hw_RTC | |||
| RTC presence | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 1 | |||
|- | |||
| 0x01AF | |||
| style="text-align:right;" | 431 | |||
| input | |||
| u16 | |||
| hw_model | |||
| Machine model | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 255 | |||
|- | |||
| 0x01A7 | |||
| style="text-align:right;" | 423 | |||
| input | |||
| u16 | |||
| hw_probe | |||
| Probe type NTC/PTC | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 1 | |||
|- | |||
| 0x01AD | |||
| style="text-align:right;" | 429 | |||
| holdng | |||
| u16 | |||
| /2 | |||
| Probe meas. stability | |||
| | |||
| style="text-align:right;" | 1 | |||
| style="text-align:right;" | 15 | |||
|- | |||
| 0x01A0 | |||
| style="text-align:right;" | 416 | |||
| holdng | |||
| u16 | |||
| /4 | |||
| Select display probe | |||
| | |||
| style="text-align:right;" | 1 | |||
| style="text-align:right;" | 3 | |||
|- | |||
| 0x01A8 | |||
| style="text-align:right;" | 424 | |||
| holdng | |||
| u16 | |||
| r3 | |||
| Direct/reverse | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01A2 | |||
| style="text-align:right;" | 418 | |||
| holdng | |||
| u16 | |||
| c0 | |||
| Start delay after Pow-on | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01A1 | |||
| style="text-align:right;" | 417 | |||
| holdng | |||
| u16 | |||
| c1 | |||
| Delay between starts | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01A4 | |||
| style="text-align:right;" | 420 | |||
| holdng | |||
| u16 | |||
| c2 | |||
| Min compressor OFF time | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01B5 | |||
| style="text-align:right;" | 437 | |||
| holdng | |||
| u16 | |||
| c3 | |||
| Min compressor ON time | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01B9 | |||
| style="text-align:right;" | 441 | |||
| holdng | |||
| u16 | |||
| c4 | |||
| Duty setting time | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01B6 | |||
| style="text-align:right;" | 438 | |||
| holdng | |||
| u16 | |||
| cc | |||
| Continuous cycle duration | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 15 | |||
|- | |||
| 0x01B3 | |||
| style="text-align:right;" | 435 | |||
| holdng | |||
| u16 | |||
| c6 | |||
| Temp al bypass after c.c. | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 15 | |||
|- | |||
| 0x01BC | |||
| style="text-align:right;" | 444 | |||
| holdng | |||
| u16 | |||
| d0 | |||
| Type of defrost | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 4 | |||
|- | |||
| 0x01BA | |||
| style="text-align:right;" | 442 | |||
| holdng | |||
| u16 | |||
| dI | |||
| Defrost interval | |||
| Часы | |||
| | |||
| | |||
|- | |||
| 0x01BE | |||
| style="text-align:right;" | 446 | |||
| holdng | |||
| u16 | |||
| dP | |||
| Maximum defrost duration | |||
| Минуты | |||
| | |||
| | |||
|- | |||
| 0x01BF | |||
| style="text-align:right;" | 447 | |||
| holdng | |||
| u16 | |||
| d5 | |||
| Def delay P-on, En Dig-In | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 199 | |||
|- | |||
| 0x01B7 | |||
| style="text-align:right;" | 439 | |||
| holdng | |||
| u16 | |||
| dd | |||
| Dripping time | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 15 | |||
|- | |||
| 0x01BB | |||
| style="text-align:right;" | 443 | |||
| holdng | |||
| u16 | |||
| d8 | |||
| Alarm off after defrost | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 15 | |||
|- | |||
| 0x01BD | |||
| style="text-align:right;" | 445 | |||
| holdng | |||
| u16 | |||
| Ad | |||
| Temperature alarm delay | |||
| Минуты | |||
| | |||
| | |||
|- | |||
| 0x01B0 | |||
| style="text-align:right;" | 432 | |||
| holdng | |||
| u16 | |||
| A4 | |||
| 3rd input conf. | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01B8 | |||
| style="text-align:right;" | 440 | |||
| holdng | |||
| u16 | |||
| A7 | |||
| Digital input alarm delay | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 199 | |||
|- | |||
| 0x01B2 | |||
| style="text-align:right;" | 434 | |||
| holdng | |||
| u16 | |||
| Acd | |||
| Dirty cond. alarm delay | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 250 | |||
|- | |||
| 0x01B1 | |||
| style="text-align:right;" | 433 | |||
| holdng | |||
| u16 | |||
| Fd | |||
| Post-dripping timeout | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 15 | |||
|- | |||
| 0x01B4 | |||
| style="text-align:right;" | 436 | |||
| input | |||
| u16 | |||
| H0 | |||
| Serial address | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 207 | |||
|- | |||
| 0x01C5 | |||
| style="text-align:right;" | 453 | |||
| holdng | |||
| u16 | |||
| H1 | |||
| AUX output configuration | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 3 | |||
|- | |||
| 0x01C9 | |||
| style="text-align:right;" | 457 | |||
| holdng | |||
| u16 | |||
| H2 | |||
| Enable keypad | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01C6 | |||
| style="text-align:right;" | 454 | |||
| holdng | |||
| u16 | |||
| H5 | |||
| ID code (read-only) | |||
| | |||
| style="text-align:right;" | 1 | |||
| style="text-align:right;" | 199 | |||
|- | |||
| 0x01C3 | |||
| style="text-align:right;" | 451 | |||
| holdng | |||
| u16 | |||
| EZY | |||
| Sel set of default param | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 4 | |||
|- | |||
| 0x01CC | |||
| style="text-align:right;" | 460 | |||
| holdng | |||
| u16 | |||
| d1d | |||
| Defrost time band 1st day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01CA | |||
| style="text-align:right;" | 458 | |||
| holdng | |||
| u16 | |||
| d1h | |||
| Time band 1st hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01CE | |||
| style="text-align:right;" | 462 | |||
| holdng | |||
| u16 | |||
| d1m | |||
| Time band 1st minutes | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01CF | |||
| style="text-align:right;" | 463 | |||
| holdng | |||
| u16 | |||
| d2d | |||
| Defrost time band 2nd day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01C7 | |||
| style="text-align:right;" | 455 | |||
| holdng | |||
| u16 | |||
| d2h | |||
| Time band 2nd hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01CB | |||
| style="text-align:right;" | 459 | |||
| holdng | |||
| u16 | |||
| d2m | |||
| Time band 2nd minutes | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01CD | |||
| style="text-align:right;" | 461 | |||
| holdng | |||
| u16 | |||
| d3d | |||
| Defrost time band 3rd day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01C0 | |||
| style="text-align:right;" | 448 | |||
| holdng | |||
| u16 | |||
| d3h | |||
| Time band 3rd hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01C8 | |||
| style="text-align:right;" | 456 | |||
| holdng | |||
| u16 | |||
| d3m | |||
| Time band 3rd minutes | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01C2 | |||
| style="text-align:right;" | 450 | |||
| holdng | |||
| u16 | |||
| d4d | |||
| Defrost time band 4th day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01C1 | |||
| style="text-align:right;" | 449 | |||
| holdng | |||
| u16 | |||
| d4h | |||
| Time band 4th hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01C4 | |||
| style="text-align:right;" | 452 | |||
| holdng | |||
| u16 | |||
| d4m | |||
| Time band 4th minutes | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01D5 | |||
| style="text-align:right;" | 469 | |||
| holdng | |||
| u16 | |||
| nOd | |||
| Night time band ON day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01D9 | |||
| style="text-align:right;" | 473 | |||
| holdng | |||
| u16 | |||
| nOh | |||
| Night time band ON hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01D6 | |||
| style="text-align:right;" | 470 | |||
| holdng | |||
| u16 | |||
| nOm | |||
| Night time band ON min. | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01D3 | |||
| style="text-align:right;" | 467 | |||
| holdng | |||
| u16 | |||
| nFd | |||
| Night time band OFF day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01DC | |||
| style="text-align:right;" | 476 | |||
| holdng | |||
| u16 | |||
| nFh | |||
| Night time band OFF hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01DA | |||
| style="text-align:right;" | 474 | |||
| holdng | |||
| u16 | |||
| nFm | |||
| Night time band OFF min | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01DE | |||
| style="text-align:right;" | 478 | |||
| holdng | |||
| u16 | |||
| AOd | |||
| AUX time band ON day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01DF | |||
| style="text-align:right;" | 479 | |||
| holdng | |||
| u16 | |||
| AOh | |||
| AUX time band ON hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01D7 | |||
| style="text-align:right;" | 471 | |||
| holdng | |||
| u16 | |||
| AOm | |||
| AUX time band ON minutes | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x01DB | |||
| style="text-align:right;" | 475 | |||
| holdng | |||
| u16 | |||
| AFd | |||
| AUX time band OFF day | |||
| Дни | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01DD | |||
| style="text-align:right;" | 477 | |||
| holdng | |||
| u16 | |||
| AFh | |||
| AUX time band OFF hour | |||
| Часы | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 23 | |||
|- | |||
| 0x01D0 | |||
| style="text-align:right;" | 464 | |||
| holdng | |||
| u16 | |||
| AFm | |||
| AUX time band OFF minutes | |||
| Минуты | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 59 | |||
|- | |||
| 0x0004 | |||
| style="text-align:right;" | 4 | |||
| discrete | |||
| u16 | |||
| s_pre1 | |||
| 1st probe alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0001 | |||
| style="text-align:right;" | 1 | |||
| discrete | |||
| u16 | |||
| s_pre2 | |||
| 2nd probe alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0009 | |||
| style="text-align:right;" | 9 | |||
| discrete | |||
| u16 | |||
| s_pre3 | |||
| 3rd probe alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x000C | |||
| style="text-align:right;" | 12 | |||
| discrete | |||
| u16 | |||
| s_LO | |||
| Low temperature alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0003 | |||
| style="text-align:right;" | 3 | |||
| discrete | |||
| u16 | |||
| s_HI | |||
| High temperature alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0006 | |||
| style="text-align:right;" | 6 | |||
| discrete | |||
| u16 | |||
| s_IA | |||
| External immediate alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x000F | |||
| style="text-align:right;" | 15 | |||
| discrete | |||
| u16 | |||
| s_dA | |||
| External delay alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x000A | |||
| style="text-align:right;" | 10 | |||
| discrete | |||
| u16 | |||
| s_Ed1 | |||
| Timeout defrost alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x000E | |||
| style="text-align:right;" | 14 | |||
| discrete | |||
| u16 | |||
| s_cht | |||
| High temp cond pre-alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0002 | |||
| style="text-align:right;" | 2 | |||
| discrete | |||
| u16 | |||
| s_CHT | |||
| High temp condenser alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0005 | |||
| style="text-align:right;" | 5 | |||
| discrete | |||
| u16 | |||
| s_Etc | |||
| Broken RTC alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0017 | |||
| style="text-align:right;" | 23 | |||
| discrete | |||
| u16 | |||
| s_EE | |||
| Machine param e2 alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0010 | |||
| style="text-align:right;" | 16 | |||
| discrete | |||
| u16 | |||
| s_EF | |||
| Func param eeprom alarm | |||
| | |||
| | |||
| | |||
|- | |||
| 0x0019 | |||
| style="text-align:right;" | 25 | |||
| discrete | |||
| u16 | |||
| s_PreDor | |||
| Open door pre-alarm state | |||
| | |||
| | |||
| | |||
|- | |||
| 0x001C | |||
| style="text-align:right;" | 28 | |||
| discrete | |||
| u16 | |||
| s_Dor | |||
| Open door alarm state | |||
| | |||
| | |||
| | |||
|- | |||
|} | |||
== μRack == | == μRack == | ||
{{Wbincludes: | {{Wbincludes:Carel Modbus Register Table Header}} | ||
| 0x0195 | |||
| style="text-align:right;" | 405 | |||
| input | |||
| u16 | |||
| LP1 | |||
| Probe B4 | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0199 | |||
| style="text-align:right;" | 409 | |||
| input | |||
| u16 | |||
| HP/LP2 | |||
| Probe B1 | |||
| bar/°C | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0196 | |||
| style="text-align:right;" | 406 | |||
| input | |||
| u16 | |||
| B2 | |||
| Probe B2 | |||
| °C/°F | |||
| style="text-align:right;" | -40 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x0193 | |||
| style="text-align:right;" | 403 | |||
| input | |||
| u16 | |||
| B3 | |||
| Probe B3 | |||
| °C/°F | |||
| style="text-align:right;" | -40 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x019C | |||
| style="text-align:right;" | 412 | |||
| holding | |||
| u16 | |||
| r01 | |||
| Suction set point circuit 1 | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x019A | |||
| style="text-align:right;" | 410 | |||
| holding | |||
| u16 | |||
| r02 | |||
| Differential circuit 1 | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x019E | |||
| style="text-align:right;" | 414 | |||
| holding | |||
| u16 | |||
| r03 | |||
| Suction set point circuit 2 | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x019F | |||
| style="text-align:right;" | 415 | |||
| holding | |||
| u16 | |||
| r04 | |||
| Differential circuit 2 | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x0197 | |||
| style="text-align:right;" | 407 | |||
| holding | |||
| u16 | |||
| r12 | |||
| Min suction set point 1 | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x019B | |||
| style="text-align:right;" | 411 | |||
| holding | |||
| u16 | |||
| r13 | |||
| Max suction set point 1 | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x019D | |||
| style="text-align:right;" | 413 | |||
| holding | |||
| u16 | |||
| r14 | |||
| Min suction set point 2 | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0190 | |||
| style="text-align:right;" | 400 | |||
| holding | |||
| u16 | |||
| r15 | |||
| Max suction set point 2 | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x0198 | |||
| style="text-align:right;" | 408 | |||
| holding | |||
| u16 | |||
| r16(bar) | |||
| Fan set point (bar) | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0192 | |||
| style="text-align:right;" | 402 | |||
| holding | |||
| u16 | |||
| r16 (°C) | |||
| Fan set point (°C) | |||
| °C/°F | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0191 | |||
| style="text-align:right;" | 401 | |||
| holding | |||
| u16 | |||
| r17 (bar) | |||
| Fan differential (bar) | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x0194 | |||
| style="text-align:right;" | 404 | |||
| holding | |||
| u16 | |||
| r17(°C) | |||
| Fan differential (°C) | |||
| °C/°F | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x01A5 | |||
| style="text-align:right;" | 421 | |||
| holding | |||
| u16 | |||
| r25(bar) | |||
| Min fan set point (bar) | |||
| °F | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01A9 | |||
| style="text-align:right;" | 425 | |||
| holding | |||
| u16 | |||
| r25 (°C) | |||
| Min fan set point (°C) | |||
| °C/°F | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01A6 | |||
| style="text-align:right;" | 422 | |||
| holding | |||
| u16 | |||
| r26(bar) | |||
| Max fan set point (bar) | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x01A3 | |||
| style="text-align:right;" | 419 | |||
| holding | |||
| u16 | |||
| r26(°C) | |||
| Max fan set point (°C) | |||
| °C/°F | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x01AC | |||
| style="text-align:right;" | 428 | |||
| holding | |||
| u16 | |||
| r18 (bar) | |||
| Fan inverter set point (bar) | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01AA | |||
| style="text-align:right;" | 426 | |||
| holding | |||
| u16 | |||
| r18 (°C) | |||
| Fan inverter set point (°C) | |||
| °C/°F | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01AE | |||
| style="text-align:right;" | 430 | |||
| holding | |||
| u16 | |||
| r19 (bar) | |||
| Fan inverter differential | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x01AF | |||
| style="text-align:right;" | 431 | |||
| holding | |||
| u16 | |||
| r19 (°C) | |||
| Fan inverter differential | |||
| °C/°F | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x01A7 | |||
| style="text-align:right;" | 423 | |||
| holding | |||
| u16 | |||
| A01 | |||
| HP suction 1 alarm threshold | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x01AB | |||
| style="text-align:right;" | 427 | |||
| holding | |||
| u16 | |||
| A03 | |||
| LP suction 1 alarm threshold | |||
| bar | |||
| style="text-align:right;" | -0.5 | |||
| style="text-align:right;" | 7 | |||
|- | |||
| 0x01AD | |||
| style="text-align:right;" | 429 | |||
| holding | |||
| u16 | |||
| A05 | |||
| HP suction 2 alarm threshold | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x01A0 | |||
| style="text-align:right;" | 416 | |||
| holding | |||
| u16 | |||
| A07 | |||
| LP suction 2 alarm threshold | |||
| bar | |||
| style="text-align:right;" | -0.5 | |||
| style="text-align:right;" | 7 | |||
|- | |||
| 0x01A8 | |||
| style="text-align:right;" | 424 | |||
| holding | |||
| u16 | |||
| A09 (bar) | |||
| HP discharge alarm threshold (bar) | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x01A2 | |||
| style="text-align:right;" | 418 | |||
| holding | |||
| u16 | |||
| A09 (°C) | |||
| HP discharge alarm threshold (°C) | |||
| °C/°F | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x01A1 | |||
| style="text-align:right;" | 417 | |||
| holding | |||
| u16 | |||
| A10(bar) | |||
| LP discharge alarm threshold (bar) | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01A4 | |||
| style="text-align:right;" | 420 | |||
| holding | |||
| u16 | |||
| A10 (°C) | |||
| LP discharge alarm threshold (°C) | |||
| °C/°F | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01B5 | |||
| style="text-align:right;" | 437 | |||
| holding | |||
| u16 | |||
| /23 | |||
| Suction probe 4 calibration | |||
| bar | |||
| style="text-align:right;" | -12 | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x01B9 | |||
| style="text-align:right;" | 441 | |||
| holding | |||
| u16 | |||
| /24 | |||
| Discharge probe 1 calibration | |||
| bar | |||
| style="text-align:right;" | -12 | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x01B6 | |||
| style="text-align:right;" | 438 | |||
| holding | |||
| u16 | |||
| /25 | |||
| Room probe 2 calibration | |||
| °C/°F | |||
| style="text-align:right;" | -12 | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x01B3 | |||
| style="text-align:right;" | 435 | |||
| holding | |||
| u16 | |||
| /26 | |||
| Outside probe 3 calibration | |||
| °C/°F | |||
| style="text-align:right;" | -12 | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x01BC | |||
| style="text-align:right;" | 444 | |||
| holding | |||
| u16 | |||
| /17 | |||
| Min value suction transducer | |||
| bar | |||
| style="text-align:right;" | -1 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01BA | |||
| style="text-align:right;" | 442 | |||
| holding | |||
| u16 | |||
| /18 | |||
| Min value discharge transducer | |||
| bar | |||
| style="text-align:right;" | -1 | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01BE | |||
| style="text-align:right;" | 446 | |||
| holding | |||
| u16 | |||
| /19 | |||
| End scale value suction transducer | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x01BF | |||
| style="text-align:right;" | 447 | |||
| holding | |||
| u16 | |||
| /20 | |||
| End scale value discharge transducer | |||
| bar | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x01B7 | |||
| style="text-align:right;" | 439 | |||
| holding | |||
| u16 | |||
| /33 | |||
| Set point prevent high pressure function | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 40 | |||
|- | |||
| 0x01BB | |||
| style="text-align:right;" | 443 | |||
| holding | |||
| u16 | |||
| r34 | |||
| Set point offset to change set from DI | |||
| bar | |||
| style="text-align:right;" | -99 | |||
| style="text-align:right;" | 99 | |||
|- | |||
| 0x01BD | |||
| style="text-align:right;" | 445 | |||
| holding | |||
| u16 | |||
| r11 | |||
| Differential pressure for dead band by time | |||
| bar | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 20 | |||
|- | |||
| 0x01B0 | |||
| style="text-align:right;" | 432 | |||
| holding | |||
| u16 | |||
| r33 | |||
| Condensing temperature delta for floating control | |||
| °C/°F | |||
| style="text-align:right;" | -40 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x01B8 | |||
| style="text-align:right;" | 440 | |||
| holding | |||
| u16 | |||
| A16 | |||
| High temp threshold probe B2 | |||
| °C/°F | |||
| style="text-align:right;" | -40 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x01B2 | |||
| style="text-align:right;" | 434 | |||
| holding | |||
| u16 | |||
| A17 | |||
| High temp threshold probe B3 | |||
| °C/°F | |||
| style="text-align:right;" | -40 | |||
| style="text-align:right;" | 150 | |||
|- | |||
| 0x01B1 | |||
| style="text-align:right;" | 433 | |||
| holding | |||
| u16 | |||
| /00 | |||
| Type of unit | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01B4 | |||
| style="text-align:right;" | 436 | |||
| holding | |||
| u16 | |||
| /01 | |||
| Unit model | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 14 | |||
|- | |||
| 0x01C5 | |||
| style="text-align:right;" | 453 | |||
| input | |||
| u16 | |||
| - | |||
| Number of compressors | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 4 | |||
|- | |||
| 0x01C9 | |||
| style="text-align:right;" | 457 | |||
| holding | |||
| u16 | |||
| /09 | |||
| Number of fans | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 4 | |||
|- | |||
| 0x01C6 | |||
| style="text-align:right;" | 454 | |||
| input | |||
| u16 | |||
| - | |||
| Unit status | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 7 | |||
|- | |||
| 0x01C3 | |||
| style="text-align:right;" | 451 | |||
| holding | |||
| u16 | |||
| r07 | |||
| Minimum call time for compressor start (dead band) | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01CC | |||
| style="text-align:right;" | 460 | |||
| holding | |||
| u16 | |||
| r09 | |||
| Minimum call time for compressor stop (dead band) | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01CA | |||
| style="text-align:right;" | 458 | |||
| holding | |||
| u16 | |||
| C01 | |||
| Minimum compressor ON time | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01CE | |||
| style="text-align:right;" | 462 | |||
| holding | |||
| u16 | |||
| C02 | |||
| Minimum compressor OFF time | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01CF | |||
| style="text-align:right;" | 463 | |||
| holding | |||
| u16 | |||
| C03 | |||
| Minimum time between starts of different compressors | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01C7 | |||
| style="text-align:right;" | 455 | |||
| holding | |||
| u16 | |||
| C05 | |||
| Minimum time between starts of the same compressor | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01CB | |||
| style="text-align:right;" | 459 | |||
| holding | |||
| u16 | |||
| - | |||
| Fan start delay (dead band) | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01CD | |||
| style="text-align:right;" | 461 | |||
| holding | |||
| u16 | |||
| - | |||
| Fan stop delay (dead band) | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01C0 | |||
| style="text-align:right;" | 448 | |||
| holding | |||
| u16 | |||
| A18 | |||
| Liquid level alarm delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01C8 | |||
| style="text-align:right;" | 456 | |||
| holding | |||
| u16 | |||
| - | |||
| Minimum fan speed | |||
| % | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01C2 | |||
| style="text-align:right;" | 450 | |||
| holding | |||
| u16 | |||
| /07 | |||
| Number of compressors on in circuit 1 with probe damaged | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 4 | |||
|- | |||
| 0x01C1 | |||
| style="text-align:right;" | 449 | |||
| holding | |||
| u16 | |||
| /08 | |||
| Number of compressors on in circuit 2 with probe damaged | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01C4 | |||
| style="text-align:right;" | 452 | |||
| holding | |||
| u16 | |||
| /12 | |||
| Number of fans on with probe damaged | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 4 | |||
|- | |||
| 0x01D5 | |||
| style="text-align:right;" | 469 | |||
| input | |||
| u16 | |||
| - | |||
| Version of the application | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01D9 | |||
| style="text-align:right;" | 473 | |||
| holding | |||
| u16 | |||
| /35 | |||
| Type of refrigerant | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 11 | |||
|- | |||
| 0x01D6 | |||
| style="text-align:right;" | 470 | |||
| holding | |||
| u16 | |||
| /03 | |||
| Capacity of compressor 1 | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 500 | |||
|- | |||
| 0x01D3 | |||
| style="text-align:right;" | 467 | |||
| holding | |||
| u16 | |||
| /04 | |||
| Capacity of compressor 2 | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 500 | |||
|- | |||
| 0x01DC | |||
| style="text-align:right;" | 476 | |||
| holding | |||
| u16 | |||
| /05 | |||
| Capacity of compressor 3 | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 500 | |||
|- | |||
| 0x01DA | |||
| style="text-align:right;" | 474 | |||
| holding | |||
| u16 | |||
| /06 | |||
| Capacity of compressor 4 | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 500 | |||
|- | |||
| 0x01DE | |||
| style="text-align:right;" | 478 | |||
| input | |||
| u16 | |||
| /11 | |||
| Inverter readout % | |||
| % | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01DF | |||
| style="text-align:right;" | 479 | |||
| holding | |||
| u16 | |||
| /15 | |||
| Multifunction DI configuration | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 12 | |||
|- | |||
| 0x01D7 | |||
| style="text-align:right;" | 471 | |||
| holding | |||
| u16 | |||
| /16 | |||
| Type of discharge probe | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01DB | |||
| style="text-align:right;" | 475 | |||
| holding | |||
| u16 | |||
| /21 | |||
| Type of probe B2 | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01DD | |||
| style="text-align:right;" | 477 | |||
| holding | |||
| u16 | |||
| /22 | |||
| Type of probe B3 | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01D0 | |||
| style="text-align:right;" | 464 | |||
| holding | |||
| u16 | |||
| /37 | |||
| Delay restart after black out | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01D8 | |||
| style="text-align:right;" | 472 | |||
| holding | |||
| u16 | |||
| C04 | |||
| Min time between two stop calls for different compressors | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01D2 | |||
| style="text-align:right;" | 466 | |||
| holding | |||
| u16 | |||
| C06 | |||
| Time between compressor stop call with Prevent function | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01D1 | |||
| style="text-align:right;" | 465 | |||
| holding | |||
| u16 | |||
| C07 | |||
| Operating hour threshold for maintenance | |||
| h x10 | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01D4 | |||
| style="text-align:right;" | 468 | |||
| input | |||
| u16 | |||
| C08 | |||
| Compressor 1 hours | |||
| h x10 | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E5 | |||
| style="text-align:right;" | 485 | |||
| input | |||
| u16 | |||
| C10 | |||
| Compressor 2 hours | |||
| h x10 | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E9 | |||
| style="text-align:right;" | 489 | |||
| input | |||
| u16 | |||
| C12 | |||
| Compressor 3 hours | |||
| h x10 | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E6 | |||
| style="text-align:right;" | 486 | |||
| input | |||
| u16 | |||
| C14 | |||
| Compressor 4 hours | |||
| h x10 | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E3 | |||
| style="text-align:right;" | 483 | |||
| holding | |||
| u16 | |||
| r05 | |||
| Type of compressor rotation | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01EC | |||
| style="text-align:right;" | 492 | |||
| holding | |||
| u16 | |||
| r06 | |||
| Type of compressor control | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01EA | |||
| style="text-align:right;" | 490 | |||
| holding | |||
| u16 | |||
| r08 | |||
| Maximum call for compressor starts in dead band by time | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01EE | |||
| style="text-align:right;" | 494 | |||
| holding | |||
| u16 | |||
| r10 | |||
| Maximum call for compressor stops in dead band by time | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01EF | |||
| style="text-align:right;" | 495 | |||
| holding | |||
| u16 | |||
| r20 | |||
| Type of fan rotation | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 1 | |||
|- | |||
| 0x01E7 | |||
| style="text-align:right;" | 487 | |||
| holding | |||
| u16 | |||
| r21 | |||
| Type of fan control | |||
| | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 2 | |||
|- | |||
| 0x01EB | |||
| style="text-align:right;" | 491 | |||
| holding | |||
| u16 | |||
| r22 | |||
| Integral time for P+I fan control | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01ED | |||
| style="text-align:right;" | 493 | |||
| holding | |||
| u16 | |||
| r23 | |||
| Time between 2 fans starts in dead band | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E0 | |||
| style="text-align:right;" | 480 | |||
| holding | |||
| u16 | |||
| r24 | |||
| Time between 2 fans stops in dead band | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E8 | |||
| style="text-align:right;" | 488 | |||
| holding | |||
| u16 | |||
| r27 | |||
| Inverter speed up time | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E2 | |||
| style="text-align:right;" | 482 | |||
| holding | |||
| u16 | |||
| r28 | |||
| Inverter ramp up time | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01E1 | |||
| style="text-align:right;" | 481 | |||
| holding | |||
| u16 | |||
| r29 | |||
| Minimum inverter output | |||
| % | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01E4 | |||
| style="text-align:right;" | 484 | |||
| holding | |||
| u16 | |||
| r30 | |||
| Maximum inverter output | |||
| % | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 100 | |||
|- | |||
| 0x01F5 | |||
| style="text-align:right;" | 501 | |||
| holding | |||
| u16 | |||
| r31 | |||
| Triac impulse duration | |||
| ms | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 10 | |||
|- | |||
| 0x01F9 | |||
| style="text-align:right;" | 505 | |||
| holding | |||
| u16 | |||
| A02 | |||
| High suction pressure 1 alarm delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01F6 | |||
| style="text-align:right;" | 502 | |||
| holding | |||
| u16 | |||
| A04 | |||
| Low suction pressure 1 alarm delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01F3 | |||
| style="text-align:right;" | 499 | |||
| holding | |||
| u16 | |||
| A06 | |||
| High suction pressure 2 alarm delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01FC | |||
| style="text-align:right;" | 508 | |||
| holding | |||
| u16 | |||
| A08 | |||
| Low suction pressure 2 alarm delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01FA | |||
| style="text-align:right;" | 506 | |||
| holding | |||
| u16 | |||
| A11 | |||
| Low discharge pressure alarm delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01FE | |||
| style="text-align:right;" | 510 | |||
| holding | |||
| u16 | |||
| A12 | |||
| Compressor thermal overload alarm delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01FF | |||
| style="text-align:right;" | 511 | |||
| holding | |||
| u16 | |||
| A13 | |||
| Prevent time in which no compressor starts are enabled | |||
| m | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 99 | |||
|- | |||
| 0x01F7 | |||
| style="text-align:right;" | 503 | |||
| holding | |||
| u16 | |||
| A14 | |||
| Prevent time in which the activation signals the alarm | |||
| m | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01FB | |||
| style="text-align:right;" | 507 | |||
| holding | |||
| u16 | |||
| A15 | |||
| Time to reset prevent alarm | |||
| m | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 99 | |||
|- | |||
| 0x01FD | |||
| style="text-align:right;" | 509 | |||
| holding | |||
| u16 | |||
| A20 | |||
| Alarm signal delay | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01F0 | |||
| style="text-align:right;" | 496 | |||
| holding | |||
| u16 | |||
| A21 | |||
| Time to change low pressure alarm from automatic to manual | |||
| s | |||
| style="text-align:right;" | 0 | |||
| style="text-align:right;" | 999 | |||
|- | |||
| 0x01F1 | |||
| style="text-align:right;" | 497 | |||
| input | |||
| u16 | |||
| | |||
| Operating percentage of first capacity controlled compressor | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01F4 | |||
| style="text-align:right;" | 500 | |||
| input | |||
| u16 | |||
| | |||
| Operating percentage of second capacity controlled compressor | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x07 | |||
| style="text-align:right;" | 7 | |||
| coil | |||
| bool | |||
| | |||
| Unit on | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x00 | |||
| style="text-align:right;" | 0 | |||
| discrete | |||
| bool | |||
| | |||
| Status of compressor 1 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0D | |||
| style="text-align:right;" | 13 | |||
| discrete | |||
| bool | |||
| | |||
| Status of compressor 2 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x08 | |||
| style="text-align:right;" | 8 | |||
| discrete | |||
| bool | |||
| | |||
| Status of compressor 3 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0B | |||
| style="text-align:right;" | 11 | |||
| discrete | |||
| bool | |||
| | |||
| Status of compressor 4 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x04 | |||
| style="text-align:right;" | 4 | |||
| discrete | |||
| bool | |||
| | |||
| Status of fan 1 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01 | |||
| style="text-align:right;" | 1 | |||
| discrete | |||
| bool | |||
| | |||
| Status of fan 2 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x09 | |||
| style="text-align:right;" | 9 | |||
| discrete | |||
| bool | |||
| | |||
| Status of fan 3 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0C | |||
| style="text-align:right;" | 12 | |||
| discrete | |||
| bool | |||
| | |||
| Status of fan 4 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x03 | |||
| style="text-align:right;" | 3 | |||
| discrete | |||
| bool | |||
| | |||
| Status of digital input 1 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x06 | |||
| style="text-align:right;" | 6 | |||
| discrete | |||
| bool | |||
| | |||
| Status of digital input 2 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0F | |||
| style="text-align:right;" | 15 | |||
| discrete | |||
| bool | |||
| | |||
| Status of digital input 3 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0A | |||
| style="text-align:right;" | 10 | |||
| discrete | |||
| bool | |||
| | |||
| Status of digital input 4 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x0E | |||
| style="text-align:right;" | 14 | |||
| discrete | |||
| bool | |||
| | |||
| Status of digital input 5 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x02 | |||
| style="text-align:right;" | 2 | |||
| coil | |||
| bool | |||
| A19 | |||
| Reset alarms | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x05 | |||
| style="text-align:right;" | 5 | |||
| coil | |||
| bool | |||
| /14 | |||
| Digital input logic | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x017 | |||
| style="text-align:right;" | 23 | |||
| coil | |||
| bool | |||
| /28 | |||
| Alarm relay logic | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x010 | |||
| style="text-align:right;" | 16 | |||
| coil | |||
| bool | |||
| /10 | |||
| Enable fan inverter | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01D | |||
| style="text-align:right;" | 29 | |||
| coil | |||
| bool | |||
| /38 | |||
| ON/OFF from supervisor | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x018 | |||
| style="text-align:right;" | 24 | |||
| coil | |||
| bool | |||
| /32 | |||
| Enable 'prevent' control on condenser | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01B | |||
| style="text-align:right;" | 27 | |||
| coil | |||
| bool | |||
| /02 | |||
| Enable management of different compressors | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x014 | |||
| style="text-align:right;" | 20 | |||
| coil | |||
| bool | |||
| /29 | |||
| Type of compressor reset | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x011 | |||
| style="text-align:right;" | 17 | |||
| coil | |||
| bool | |||
| /30 | |||
| Type of fan reset | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x019 | |||
| style="text-align:right;" | 25 | |||
| coil | |||
| bool | |||
| /31 | |||
| Type of reset for general high press. Switch | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01C | |||
| style="text-align:right;" | 28 | |||
| coil | |||
| bool | |||
| C09 | |||
| Reset compressor 1 hours | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x013 | |||
| style="text-align:right;" | 19 | |||
| coil | |||
| bool | |||
| C11 | |||
| Reset compressor 2 hours | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x016 | |||
| style="text-align:right;" | 22 | |||
| coil | |||
| bool | |||
| C13 | |||
| Reset compressor 3 hours | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01F | |||
| style="text-align:right;" | 31 | |||
| coil | |||
| bool | |||
| C15 | |||
| Reset compressor 4 hours | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01A | |||
| style="text-align:right;" | 26 | |||
| coil | |||
| bool | |||
| r32 | |||
| Enable floating condenser control | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x01E | |||
| style="text-align:right;" | 30 | |||
| coil | |||
| bool | |||
| A22 | |||
| Enable unit Off due to probe fault | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x012 | |||
| style="text-align:right;" | 18 | |||
| coil | |||
| bool | |||
| /13 | |||
| Enable fan with comp on | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x015 | |||
| style="text-align:right;" | 21 | |||
| discrete | |||
| bool | |||
| A01 | |||
| Alarm: compressor 1 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x027 | |||
| style="text-align:right;" | 39 | |||
| discrete | |||
| bool | |||
| A02 | |||
| Alarm: compressor 2 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x020 | |||
| style="text-align:right;" | 32 | |||
| discrete | |||
| bool | |||
| A03 | |||
| Alarm: compressor 3 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x02D | |||
| style="text-align:right;" | 45 | |||
| discrete | |||
| bool | |||
| A04 | |||
| Alarm: compressor 4 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x028 | |||
| style="text-align:right;" | 40 | |||
| discrete | |||
| bool | |||
| A22 | |||
| Alarm: fan 1 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x02B | |||
| style="text-align:right;" | 43 | |||
| discrete | |||
| bool | |||
| A23 | |||
| Alarm: fan 2 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x024 | |||
| style="text-align:right;" | 36 | |||
| discrete | |||
| bool | |||
| A24 | |||
| Alarm: fan 3 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x021 | |||
| style="text-align:right;" | 33 | |||
| discrete | |||
| bool | |||
| A25 | |||
| Alarm: fan 4 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x029 | |||
| style="text-align:right;" | 41 | |||
| discrete | |||
| bool | |||
| A09 | |||
| Alarm: liquid level | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x02C | |||
| style="text-align:right;" | 44 | |||
| discrete | |||
| bool | |||
| A10 | |||
| Alarm: general low suction pressure 1 (from multifunction DI) | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x023 | |||
| style="text-align:right;" | 35 | |||
| discrete | |||
| bool | |||
| A11 | |||
| Alarm: general low suction pressure 2 (from multifunction DI) | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x026 | |||
| style="text-align:right;" | 38 | |||
| discrete | |||
| bool | |||
| A13 | |||
| Alarm: low discharge pressure | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x02F | |||
| style="text-align:right;" | 47 | |||
| discrete | |||
| bool | |||
| A14 | |||
| Alarm: high discharge pressure | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x02A | |||
| style="text-align:right;" | 42 | |||
| discrete | |||
| bool | |||
| A15 | |||
| Alarm: low suction pressure 1 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x02E | |||
| style="text-align:right;" | 46 | |||
| discrete | |||
| bool | |||
| A16 | |||
| Alarm: high suction pressure 1 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x022 | |||
| style="text-align:right;" | 34 | |||
| discrete | |||
| bool | |||
| A17 | |||
| Alarm: low suction pressure 2 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x025 | |||
| style="text-align:right;" | 37 | |||
| discrete | |||
| bool | |||
| A18 | |||
| Alarm: high suction pressure 2 | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x037 | |||
| style="text-align:right;" | 55 | |||
| discrete | |||
| bool | |||
| A20 | |||
| Probe B1 faulty or disconnected | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x030 | |||
| style="text-align:right;" | 48 | |||
| discrete | |||
| bool | |||
| AB2 | |||
| Probe B2 faulty or disconnected | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x03D | |||
| style="text-align:right;" | 61 | |||
| discrete | |||
| bool | |||
| AB3 | |||
| Probe B3 faulty or disconnected | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x038 | |||
| style="text-align:right;" | 56 | |||
| discrete | |||
| bool | |||
| A19 | |||
| Probe B4 faulty or disconnected | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x03B | |||
| style="text-align:right;" | 59 | |||
| discrete | |||
| bool | |||
| A05 | |||
| Compressor 1 maintenance | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x034 | |||
| style="text-align:right;" | 52 | |||
| discrete | |||
| bool | |||
| A06 | |||
| Compressor 2 maintenance | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x031 | |||
| style="text-align:right;" | 49 | |||
| discrete | |||
| bool | |||
| A07 | |||
| Compressor 3 maintenance | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x039 | |||
| style="text-align:right;" | 57 | |||
| discrete | |||
| bool | |||
| A08 | |||
| Compressor 4 maintenance | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x03C | |||
| style="text-align:right;" | 60 | |||
| discrete | |||
| bool | |||
| A12 | |||
| General discharge pressure switch (from multifunction DI) | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x033 | |||
| style="text-align:right;" | 51 | |||
| discrete | |||
| bool | |||
| A26 | |||
| General fan thermal overload | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x036 | |||
| style="text-align:right;" | 54 | |||
| discrete | |||
| bool | |||
| A27 | |||
| Prevent high discharge pressure | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x03F | |||
| style="text-align:right;" | 63 | |||
| discrete | |||
| bool | |||
| A28 | |||
| Compressors off due to prevent | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x03A | |||
| style="text-align:right;" | 58 | |||
| discrete | |||
| bool | |||
| A29 | |||
| Excessive prevent frequency | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x03E | |||
| style="text-align:right;" | 62 | |||
| discrete | |||
| bool | |||
| HtE | |||
| High outside temperature | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
| 0x032 | |||
| style="text-align:right;" | 50 | |||
| discrete | |||
| bool | |||
| HtA | |||
| High room temperature | |||
| | |||
| style="text-align:right;" | | |||
| style="text-align:right;" | | |||
|- | |||
|} | |||
==Общие регистры== | ==Общие регистры== | ||
{{Wbincludes: | {{Wbincludes:Common Modbus Registers|addlines=true}} | ||
| 816-818 || 0x0330 - 0x0332 || Input || RO || u16 || Используются для определения модели контроллера || | |||
|- | |- | ||
|} | |} |
Версия 12:35, 5 сентября 2022
Описание
Регистры сетевой карты WB-REF-U-CR зависят от используемого холодильного контроллера Carel и перечислены в таблицах ниже. Данные в таблицах сгруппированы по функциям.
Служебные регистры сетевой карты вы найдёте в разделе Общие регистры.
PJ BASIC
Адрес | Тип | Формат | Имя | Назначение | Единицы измерения |
Значения | |||
---|---|---|---|---|---|---|---|---|---|
в Hex | в DEC | Минимум | Максимум | ||||||
0x0004 | 4 | discrete | bool | s_pre1 | 1st probe alarm | ||||
0x0001 | 1 | discrete | bool | s_pre2 | 2nd probe alarm | ||||
0x0009 | 9 | discrete | bool | s_pre3 | 3rd probe alarm | ||||
0x000C | 12 | discrete | bool | s_LO | Low temperature alarm | ||||
0x0003 | 3 | discrete | bool | s_HI | High temperature alarm | ||||
0x0006 | 6 | discrete | bool | s_IA | External immediate alarm | ||||
0x000F | 15 | discrete | bool | s_dA | External delay alarm | ||||
0x000A | 10 | discrete | bool | s_Ed1 | Timeout defrost alarm | ||||
0x000E | 14 | discrete | bool | s_cht | High temperature condense | ||||
0x0002 | 2 | discrete | bool | s_CHT | High temperature condense | ||||
0x0005 | 5 | discrete | bool | s_Etc | Broken RTC alarm | ||||
0x0017 | 23 | discrete | bool | s_EE | Machine parameters eeprom | ||||
0x0010 | 16 | discrete | bool | s_EF | Functions parameters eepr | ||||
0x0019 | 25 | discrete | bool | s_PreDor | Pre-opened door alarm | 0 | 0 | ||
0x001C | 28 | discrete | bool | s_Dor | Opened door alarm | 0 | 0 | ||
0x0195 | 405 | input | s16 | s_pr1 | Probe 1 reading | 0.1°C/°F | 0 | 0 | |
0x0199 | 409 | input | s16 | s_pr2 | Probe 2 reading | 0.1°C/°F | 0 | 0 | |
0x0196 | 406 | input | s16 | s_pr3 | Probe 3 reading | 0.1°C/°F | 0 | 0 | |
0x0193 | 403 | holdng | s16 | /C1 | Probe 1 offset | 0.1°C/°F | -20 | 20 | |
0x019C | 412 | holdng | s16 | /C2 | Probe 2 offset | 0.1°C/°F | -20 | 20 | |
0x019A | 410 | holdng | s16 | St | Set point | 0.1°C/°F | |||
0x019E | 414 | holdng | s16 | rd | Control differential | 0.1°C/°F | 0 | 19 | |
0x019F | 415 | holdng | s16 | r1 | Minimum set point allowe | 0.1°C/°F | -50 | ||
0x0197 | 407 | holdng | s16 | r2 | Maximum set point allowed | 0.1°C/°F | 90 | ||
0x019B | 411 | holdng | s16 | dt | End defrost temperature | 0.1°C/°F | -50 | 90 | |
0x019D | 413 | holdng | s16 | A0 | Alarm and fan differentia | 0.1°C/°F | -20 | 20 | |
0x0190 | 400 | holdng | s16 | AL | Absolute/Relative tempera | 0.1°C/°F | -50 | 90 | |
0x0198 | 408 | holdng | s16 | AH | Absolute/Relative tempera | 0.1°C/°F | -50 | 90 | |
0x0192 | 402 | holdng | s16 | F1 | Fan control set point | 0.1°C/°F | -50 | 90 | |
0x0007 | 7 | discrete | u16 | s_din1 | Status of digital input 1 | 0 | 0 | ||
0x0000 | 0 | discrete | u16 | s_r1 | Compressor relay status | 0 | 0 | ||
0x000D | 13 | discrete | u16 | s_r2 | Defrost relay status | 0 | 0 | ||
0x0008 | 8 | discrete | u16 | s_r3 | Fan relay status | 0 | 0 | ||
0x000B | 11 | discrete | u16 | s_r4 | Auxiliary relay status | 0 | 0 | ||
0x001D | 29 | discrete | u16 | s_DEF | Defrost status | 0 | 0 | ||
0x0018 | 24 | coil | s16 | s_cDEF | Defrost command | 0 | 1 | ||
0x001B | 27 | discrete | u16 | s_CC | Continuous cycle status | 0 | 0 | ||
0x0014 | 20 | coil | u16 | s_cCC | Continuous cycle command | 0 | 1 | ||
0x0013 | 19 | coil | u16 | F0 | Fan management | 0 | 1 | ||
0x0016 | 22 | coil | u16 | F3 | Fan in defrost | 0 | 1 | ||
0x001F | 31 | coil | u16 | s_cONOFF | ON/OFF command | 0 | 1 | ||
0x01A6 | 422 | holdng | u16 | c0 | Comp. and fan start delay | Минуты | 0 | 99 | |
0x01A3 | 419 | holdng | u16 | c2 | Minimum compressor off ti | Минуты | 0 | 99 | |
0x01AC | 428 | holdng | u16 | d0 | Defrost type | 0 | 4 | ||
0x01AA | 426 | holdng | u16 | dI | Interval between defrosts | Часы | 0 | 24 | |
0x01AE | 430 | holdng | u16 | dP | Maximum defrost duration | Минуты | 1 | 99 | |
0x01AF | 431 | holdng | u16 | dd | Dripping time after defro | Минуты | 0 | 15 | |
0x01A7 | 423 | holdng | u16 | Ad | Low and high temperature | Минуты | 0 | 99 | |
0x01AB | 427 | holdng | u16 | A4 | Third input configuration | 0 | 2 | ||
0x01AD | 429 | holdng | u16 | F2 | Fan off with compressor o | 0.1°C/°F | 0 | 2 | |
0x01A0 | 416 | holdng | u16 | Fd | Post dripping time | Минуты | 0 | 15 | |
0x01A8 | 424 | holdng | u16 | F4 | Start delay when fan on | Секунды | 1 | 99 | |
0x01A2 | 418 | holdng | u16 | F5 | Fan on time (with F2=2) | Минуты | 1 | 99 | |
0x01A1 | 417 | holdng | u16 | F6 | Fan off time (with F2=2) | Минуты | 1 | 99 | |
0x01A4 | 420 | input | s16 | H0 | Serial address | 0 | 207 |
PJ EASY
Адрес | Тип | Формат | Имя | Назначение | Единицы измерения |
Значения | |||
---|---|---|---|---|---|---|---|---|---|
в Hex | в DEC | Минимум | Максимум | ||||||
0x0007 | 7 | discrete | u16 | Dig.input | Digital input status | ||||
0x0000 | 0 | discrete | u16 | Rel. comp. | Compressor relay status | ||||
0x000D | 13 | discrete | u16 | Rel. defr. | Defrost relay status | ||||
0x0008 | 8 | discrete | u16 | Rel. fan. | Fan relay status | ||||
0x000B | 11 | discrete | u16 | Rel.AUX | Activate AUX command | ||||
0x001D | 29 | discrete | u16 | Defrost | Defrost status | ||||
0x0018 | 24 | coil | u16 | Defrost | Activate defrost command | ||||
0x001B | 27 | discrete | u16 | C.C. | Continuous cycle status | ||||
0x0014 | 20 | coil | u16 | C.C. | Activation contin. cycle | ||||
0x0011 | 17 | discrete | u16 | s_nRTC | Set point started by RTC | ||||
0x0013 | 19 | coil | u16 | /5 | Select C/F | ||||
0x0016 | 22 | coil | u16 | /6 | Disable decimal point | ||||
0x001F | 31 | coil | u16 | d4 | Defrost at power-on | ||||
0x001A | 26 | coil | u16 | d6 | Display lock during defr. | ||||
0x001E | 30 | coil | u16 | d9 | Def prior over comp prots | ||||
0x0012 | 18 | coil | u16 | dC | Time base | ||||
0x0015 | 21 | coil | u16 | A8 | En alarm Ed | ||||
0x0027 | 39 | coil | u16 | F0 | Enable evap fan control | ||||
0x0020 | 32 | coil | u16 | F2 | Stop fans if compr stops | ||||
0x002D | 45 | coil | u16 | F3 | Stop fans during defrost | ||||
0x0028 | 40 | coil | u16 | H4 | Buzzer inhibition | ||||
0x002B | 43 | coil | u16 | tEn | Enable RTC | ||||
0x0024 | 36 | coil | u16 | ON/OFF | Controller ON/OFF command | ||||
0x0195 | 405 | input | u16 | d/ | Defrost probe value | °C | 0 | 0 | |
0x0199 | 409 | input | u16 | s_pr1 | Probe 1 status | °C | 0 | 0 | |
0x0196 | 406 | input | u16 | s_pr2 | Probe 2 status | °C/°F | 0 | 0 | |
0x0193 | 403 | input | u16 | s_pr3 | Probe 3 status | °C/°F | 0 | 0 | |
0x019C | 412 | holdng | u16 | /C1 | Probe 1 offset | °C | 12 | ||
0x019A | 410 | holdng | u16 | /C2 | Probe 2 offset | °C/°F | 12 | ||
0x019E | 414 | holdng | u16 | /C3 | Probe 3 offset | °C/°F | 12 | ||
0x019F | 415 | holdng | u16 | St | User set point | °C | |||
0x0197 | 407 | holdng | u16 | rd | Differential | °C | 0 | 19 | |
0x019B | 411 | holdng | u16 | r1 | Minimum set point allowed | °C/°F | -50 | pk78 | |
0x019D | 413 | holdng | u16 | r2 | Maximum set point allowed | °C/°F | pk79 | 150 | |
0x0190 | 400 | holdng | u16 | r4 | Night-time set point diff | °C/°F | -50 | 50 | |
0x0198 | 408 | holdng | u16 | dt | End defrost temperature | °C/°F | -50 | 127 | |
0x0192 | 402 | holdng | u16 | A0 | Al and fan differential | °C/°F | -20 | 20 | |
0x0191 | 401 | holdng | u16 | AL | Low temperature alarm | °C | -50 | 150 | |
0x0194 | 404 | holdng | u16 | AH | High temperature alarm | °C | -50 | 150 | |
0x01A5 | 421 | holdng | u16 | Ac | Dirty cond Al set point | °C/°F | -50 | 150 | |
0x01A9 | 425 | holdng | u16 | AE | Dirty cond Al temp. diff. | °C/°F | 0.1 | 20 | |
0x01A6 | 422 | holdng | u16 | F1 | Evap fan control sp | °C | -50 | 127 | |
0x01A3 | 419 | holdng | u16 | tc_d | RTC day of the week | День | 1 | 7 | |
0x01AC | 428 | holdng | u16 | tc_h | RTC hour | Часы | 0 | 23 | |
0x01AA | 426 | holdng | u16 | tc_m | RTC minutes | Минуты | 0 | 59 | |
0x01AE | 430 | input | u16 | hw_RTC | RTC presence | 0 | 1 | ||
0x01AF | 431 | input | u16 | hw_model | Machine model | 0 | 255 | ||
0x01A7 | 423 | input | u16 | hw_probe | Probe type NTC/PTC | 0 | 1 | ||
0x01AD | 429 | holdng | u16 | /2 | Probe meas. stability | 1 | 15 | ||
0x01A0 | 416 | holdng | u16 | /4 | Select display probe | 1 | 3 | ||
0x01A8 | 424 | holdng | u16 | r3 | Direct/reverse | 0 | 2 | ||
0x01A2 | 418 | holdng | u16 | c0 | Start delay after Pow-on | Минуты | 0 | 100 | |
0x01A1 | 417 | holdng | u16 | c1 | Delay between starts | Минуты | 0 | 100 | |
0x01A4 | 420 | holdng | u16 | c2 | Min compressor OFF time | Минуты | 0 | 100 | |
0x01B5 | 437 | holdng | u16 | c3 | Min compressor ON time | Минуты | 0 | 100 | |
0x01B9 | 441 | holdng | u16 | c4 | Duty setting time | Минуты | 0 | 100 | |
0x01B6 | 438 | holdng | u16 | cc | Continuous cycle duration | Часы | 0 | 15 | |
0x01B3 | 435 | holdng | u16 | c6 | Temp al bypass after c.c. | Часы | 0 | 15 | |
0x01BC | 444 | holdng | u16 | d0 | Type of defrost | 0 | 4 | ||
0x01BA | 442 | holdng | u16 | dI | Defrost interval | Часы | |||
0x01BE | 446 | holdng | u16 | dP | Maximum defrost duration | Минуты | |||
0x01BF | 447 | holdng | u16 | d5 | Def delay P-on, En Dig-In | Минуты | 0 | 199 | |
0x01B7 | 439 | holdng | u16 | dd | Dripping time | Минуты | 0 | 15 | |
0x01BB | 443 | holdng | u16 | d8 | Alarm off after defrost | Часы | 0 | 15 | |
0x01BD | 445 | holdng | u16 | Ad | Temperature alarm delay | Минуты | |||
0x01B0 | 432 | holdng | u16 | A4 | 3rd input conf. | 0 | 11 | ||
0x01B8 | 440 | holdng | u16 | A7 | Digital input alarm delay | Минуты | 0 | 199 | |
0x01B2 | 434 | holdng | u16 | Acd | Dirty cond. alarm delay | Минуты | 0 | 250 | |
0x01B1 | 433 | holdng | u16 | Fd | Post-dripping timeout | Минуты | 0 | 15 | |
0x01B4 | 436 | input | u16 | H0 | Serial address | 0 | 207 | ||
0x01C5 | 453 | holdng | u16 | H1 | AUX output configuration | 0 | 3 | ||
0x01C9 | 457 | holdng | u16 | H2 | Enable keypad | 0 | 2 | ||
0x01C6 | 454 | holdng | u16 | H5 | ID code (read-only) | 1 | 199 | ||
0x01C3 | 451 | holdng | u16 | EZY | Sel set of default param | 0 | 4 | ||
0x01CC | 460 | holdng | u16 | d1d | Defrost time band 1st day | Дни | 0 | 11 | |
0x01CA | 458 | holdng | u16 | d1h | Time band 1st hour | Часы | 0 | 23 | |
0x01CE | 462 | holdng | u16 | d1m | Time band 1st minutes | Минуты | 0 | 59 | |
0x01CF | 463 | holdng | u16 | d2d | Defrost time band 2nd day | Дни | 0 | 11 | |
0x01C7 | 455 | holdng | u16 | d2h | Time band 2nd hour | Часы | 0 | 23 | |
0x01CB | 459 | holdng | u16 | d2m | Time band 2nd minutes | Минуты | 0 | 59 | |
0x01CD | 461 | holdng | u16 | d3d | Defrost time band 3rd day | Дни | 0 | 11 | |
0x01C0 | 448 | holdng | u16 | d3h | Time band 3rd hour | Часы | 0 | 23 | |
0x01C8 | 456 | holdng | u16 | d3m | Time band 3rd minutes | Минуты | 0 | 59 | |
0x01C2 | 450 | holdng | u16 | d4d | Defrost time band 4th day | Дни | 0 | 11 | |
0x01C1 | 449 | holdng | u16 | d4h | Time band 4th hour | Часы | 0 | 23 | |
0x01C4 | 452 | holdng | u16 | d4m | Time band 4th minutes | Минуты | 0 | 59 | |
0x01D5 | 469 | holdng | u16 | nOd | Night time band ON day | Дни | 0 | 11 | |
0x01D9 | 473 | holdng | u16 | nOh | Night time band ON hour | Часы | 0 | 23 | |
0x01D6 | 470 | holdng | u16 | nOm | Night time band ON min. | Минуты | 0 | 59 | |
0x01D3 | 467 | holdng | u16 | nFd | Night time band OFF day | Дни | 0 | 11 | |
0x01DC | 476 | holdng | u16 | nFh | Night time band OFF hour | Часы | 0 | 23 | |
0x01DA | 474 | holdng | u16 | nFm | Night time band OFF min | Минуты | 0 | 59 | |
0x01DE | 478 | holdng | u16 | AOd | AUX time band ON day | Дни | 0 | 11 | |
0x01DF | 479 | holdng | u16 | AOh | AUX time band ON hour | Часы | 0 | 23 | |
0x01D7 | 471 | holdng | u16 | AOm | AUX time band ON minutes | Минуты | 0 | 59 | |
0x01DB | 475 | holdng | u16 | AFd | AUX time band OFF day | Дни | 0 | 11 | |
0x01DD | 477 | holdng | u16 | AFh | AUX time band OFF hour | Часы | 0 | 23 | |
0x01D0 | 464 | holdng | u16 | AFm | AUX time band OFF minutes | Минуты | 0 | 59 | |
0x0004 | 4 | discrete | u16 | s_pre1 | 1st probe alarm | ||||
0x0001 | 1 | discrete | u16 | s_pre2 | 2nd probe alarm | ||||
0x0009 | 9 | discrete | u16 | s_pre3 | 3rd probe alarm | ||||
0x000C | 12 | discrete | u16 | s_LO | Low temperature alarm | ||||
0x0003 | 3 | discrete | u16 | s_HI | High temperature alarm | ||||
0x0006 | 6 | discrete | u16 | s_IA | External immediate alarm | ||||
0x000F | 15 | discrete | u16 | s_dA | External delay alarm | ||||
0x000A | 10 | discrete | u16 | s_Ed1 | Timeout defrost alarm | ||||
0x000E | 14 | discrete | u16 | s_cht | High temp cond pre-alarm | ||||
0x0002 | 2 | discrete | u16 | s_CHT | High temp condenser alarm | ||||
0x0005 | 5 | discrete | u16 | s_Etc | Broken RTC alarm | ||||
0x0017 | 23 | discrete | u16 | s_EE | Machine param e2 alarm | ||||
0x0010 | 16 | discrete | u16 | s_EF | Func param eeprom alarm | ||||
0x0019 | 25 | discrete | u16 | s_PreDor | Open door pre-alarm state | ||||
0x001C | 28 | discrete | u16 | s_Dor | Open door alarm state |
μRack
Адрес | Тип | Формат | Имя | Назначение | Единицы измерения |
Значения | |||
---|---|---|---|---|---|---|---|---|---|
в Hex | в DEC | Минимум | Максимум | ||||||
0x0195 | 405 | input | u16 | LP1 | Probe B4 | bar | |||
0x0199 | 409 | input | u16 | HP/LP2 | Probe B1 | bar/°C | |||
0x0196 | 406 | input | u16 | B2 | Probe B2 | °C/°F | -40 | 150 | |
0x0193 | 403 | input | u16 | B3 | Probe B3 | °C/°F | -40 | 150 | |
0x019C | 412 | holding | u16 | r01 | Suction set point circuit 1 | bar | |||
0x019A | 410 | holding | u16 | r02 | Differential circuit 1 | bar | 0 | 20 | |
0x019E | 414 | holding | u16 | r03 | Suction set point circuit 2 | bar | |||
0x019F | 415 | holding | u16 | r04 | Differential circuit 2 | bar | 0 | 20 | |
0x0197 | 407 | holding | u16 | r12 | Min suction set point 1 | bar | 0 | ||
0x019B | 411 | holding | u16 | r13 | Max suction set point 1 | bar | 40 | ||
0x019D | 413 | holding | u16 | r14 | Min suction set point 2 | bar | 0 | ||
0x0190 | 400 | holding | u16 | r15 | Max suction set point 2 | bar | 40 | ||
0x0198 | 408 | holding | u16 | r16(bar) | Fan set point (bar) | bar | |||
0x0192 | 402 | holding | u16 | r16 (°C) | Fan set point (°C) | °C/°F | |||
0x0191 | 401 | holding | u16 | r17 (bar) | Fan differential (bar) | bar | 0 | 20 | |
0x0194 | 404 | holding | u16 | r17(°C) | Fan differential (°C) | °C/°F | 0 | 20 | |
0x01A5 | 421 | holding | u16 | r25(bar) | Min fan set point (bar) | °F | 0 | ||
0x01A9 | 425 | holding | u16 | r25 (°C) | Min fan set point (°C) | °C/°F | 0 | ||
0x01A6 | 422 | holding | u16 | r26(bar) | Max fan set point (bar) | bar | 40 | ||
0x01A3 | 419 | holding | u16 | r26(°C) | Max fan set point (°C) | °C/°F | 150 | ||
0x01AC | 428 | holding | u16 | r18 (bar) | Fan inverter set point (bar) | bar | |||
0x01AA | 426 | holding | u16 | r18 (°C) | Fan inverter set point (°C) | °C/°F | |||
0x01AE | 430 | holding | u16 | r19 (bar) | Fan inverter differential | bar | 0 | 20 | |
0x01AF | 431 | holding | u16 | r19 (°C) | Fan inverter differential | °C/°F | 0 | 20 | |
0x01A7 | 423 | holding | u16 | A01 | HP suction 1 alarm threshold | bar | 40 | ||
0x01AB | 427 | holding | u16 | A03 | LP suction 1 alarm threshold | bar | -0.5 | 7 | |
0x01AD | 429 | holding | u16 | A05 | HP suction 2 alarm threshold | bar | 40 | ||
0x01A0 | 416 | holding | u16 | A07 | LP suction 2 alarm threshold | bar | -0.5 | 7 | |
0x01A8 | 424 | holding | u16 | A09 (bar) | HP discharge alarm threshold (bar) | bar | 40 | ||
0x01A2 | 418 | holding | u16 | A09 (°C) | HP discharge alarm threshold (°C) | °C/°F | 150 | ||
0x01A1 | 417 | holding | u16 | A10(bar) | LP discharge alarm threshold (bar) | bar | 0 | ||
0x01A4 | 420 | holding | u16 | A10 (°C) | LP discharge alarm threshold (°C) | °C/°F | 0 | ||
0x01B5 | 437 | holding | u16 | /23 | Suction probe 4 calibration | bar | -12 | 12 | |
0x01B9 | 441 | holding | u16 | /24 | Discharge probe 1 calibration | bar | -12 | 12 | |
0x01B6 | 438 | holding | u16 | /25 | Room probe 2 calibration | °C/°F | -12 | 12 | |
0x01B3 | 435 | holding | u16 | /26 | Outside probe 3 calibration | °C/°F | -12 | 12 | |
0x01BC | 444 | holding | u16 | /17 | Min value suction transducer | bar | -1 | ||
0x01BA | 442 | holding | u16 | /18 | Min value discharge transducer | bar | -1 | ||
0x01BE | 446 | holding | u16 | /19 | End scale value suction transducer | bar | 40 | ||
0x01BF | 447 | holding | u16 | /20 | End scale value discharge transducer | bar | 40 | ||
0x01B7 | 439 | holding | u16 | /33 | Set point prevent high pressure function | bar | 0 | 40 | |
0x01BB | 443 | holding | u16 | r34 | Set point offset to change set from DI | bar | -99 | 99 | |
0x01BD | 445 | holding | u16 | r11 | Differential pressure for dead band by time | bar | 0 | 20 | |
0x01B0 | 432 | holding | u16 | r33 | Condensing temperature delta for floating control | °C/°F | -40 | 150 | |
0x01B8 | 440 | holding | u16 | A16 | High temp threshold probe B2 | °C/°F | -40 | 150 | |
0x01B2 | 434 | holding | u16 | A17 | High temp threshold probe B3 | °C/°F | -40 | 150 | |
0x01B1 | 433 | holding | u16 | /00 | Type of unit | 0 | 2 | ||
0x01B4 | 436 | holding | u16 | /01 | Unit model | 0 | 14 | ||
0x01C5 | 453 | input | u16 | - | Number of compressors | 0 | 4 | ||
0x01C9 | 457 | holding | u16 | /09 | Number of fans | 0 | 4 | ||
0x01C6 | 454 | input | u16 | - | Unit status | 0 | 7 | ||
0x01C3 | 451 | holding | u16 | r07 | Minimum call time for compressor start (dead band) | s | 0 | 999 | |
0x01CC | 460 | holding | u16 | r09 | Minimum call time for compressor stop (dead band) | s | 0 | 999 | |
0x01CA | 458 | holding | u16 | C01 | Minimum compressor ON time | s | 0 | 999 | |
0x01CE | 462 | holding | u16 | C02 | Minimum compressor OFF time | s | 0 | 999 | |
0x01CF | 463 | holding | u16 | C03 | Minimum time between starts of different compressors | s | 0 | 999 | |
0x01C7 | 455 | holding | u16 | C05 | Minimum time between starts of the same compressor | s | 0 | 999 | |
0x01CB | 459 | holding | u16 | - | Fan start delay (dead band) | s | 0 | 999 | |
0x01CD | 461 | holding | u16 | - | Fan stop delay (dead band) | s | 0 | 999 | |
0x01C0 | 448 | holding | u16 | A18 | Liquid level alarm delay | s | 0 | 999 | |
0x01C8 | 456 | holding | u16 | - | Minimum fan speed | % | 0 | 100 | |
0x01C2 | 450 | holding | u16 | /07 | Number of compressors on in circuit 1 with probe damaged | 0 | 4 | ||
0x01C1 | 449 | holding | u16 | /08 | Number of compressors on in circuit 2 with probe damaged | 0 | 2 | ||
0x01C4 | 452 | holding | u16 | /12 | Number of fans on with probe damaged | 0 | 4 | ||
0x01D5 | 469 | input | u16 | - | Version of the application | ||||
0x01D9 | 473 | holding | u16 | /35 | Type of refrigerant | 0 | 11 | ||
0x01D6 | 470 | holding | u16 | /03 | Capacity of compressor 1 | 0 | 500 | ||
0x01D3 | 467 | holding | u16 | /04 | Capacity of compressor 2 | 0 | 500 | ||
0x01DC | 476 | holding | u16 | /05 | Capacity of compressor 3 | 0 | 500 | ||
0x01DA | 474 | holding | u16 | /06 | Capacity of compressor 4 | 0 | 500 | ||
0x01DE | 478 | input | u16 | /11 | Inverter readout % | % | 0 | 100 | |
0x01DF | 479 | holding | u16 | /15 | Multifunction DI configuration | 0 | 12 | ||
0x01D7 | 471 | holding | u16 | /16 | Type of discharge probe | 0 | 2 | ||
0x01DB | 475 | holding | u16 | /21 | Type of probe B2 | 0 | 2 | ||
0x01DD | 477 | holding | u16 | /22 | Type of probe B3 | 0 | 2 | ||
0x01D0 | 464 | holding | u16 | /37 | Delay restart after black out | s | 0 | 999 | |
0x01D8 | 472 | holding | u16 | C04 | Min time between two stop calls for different compressors | s | 0 | 999 | |
0x01D2 | 466 | holding | u16 | C06 | Time between compressor stop call with Prevent function | s | 0 | 999 | |
0x01D1 | 465 | holding | u16 | C07 | Operating hour threshold for maintenance | h x10 | 0 | 999 | |
0x01D4 | 468 | input | u16 | C08 | Compressor 1 hours | h x10 | 0 | 999 | |
0x01E5 | 485 | input | u16 | C10 | Compressor 2 hours | h x10 | 0 | 999 | |
0x01E9 | 489 | input | u16 | C12 | Compressor 3 hours | h x10 | 0 | 999 | |
0x01E6 | 486 | input | u16 | C14 | Compressor 4 hours | h x10 | 0 | 999 | |
0x01E3 | 483 | holding | u16 | r05 | Type of compressor rotation | 0 | 2 | ||
0x01EC | 492 | holding | u16 | r06 | Type of compressor control | 0 | 2 | ||
0x01EA | 490 | holding | u16 | r08 | Maximum call for compressor starts in dead band by time | s | 0 | 999 | |
0x01EE | 494 | holding | u16 | r10 | Maximum call for compressor stops in dead band by time | s | 0 | 999 | |
0x01EF | 495 | holding | u16 | r20 | Type of fan rotation | 0 | 1 | ||
0x01E7 | 487 | holding | u16 | r21 | Type of fan control | 0 | 2 | ||
0x01EB | 491 | holding | u16 | r22 | Integral time for P+I fan control | s | 0 | 999 | |
0x01ED | 493 | holding | u16 | r23 | Time between 2 fans starts in dead band | s | 0 | 999 | |
0x01E0 | 480 | holding | u16 | r24 | Time between 2 fans stops in dead band | s | 0 | 999 | |
0x01E8 | 488 | holding | u16 | r27 | Inverter speed up time | s | 0 | 999 | |
0x01E2 | 482 | holding | u16 | r28 | Inverter ramp up time | s | 0 | 999 | |
0x01E1 | 481 | holding | u16 | r29 | Minimum inverter output | % | 0 | 100 | |
0x01E4 | 484 | holding | u16 | r30 | Maximum inverter output | % | 0 | 100 | |
0x01F5 | 501 | holding | u16 | r31 | Triac impulse duration | ms | 0 | 10 | |
0x01F9 | 505 | holding | u16 | A02 | High suction pressure 1 alarm delay | s | 0 | 999 | |
0x01F6 | 502 | holding | u16 | A04 | Low suction pressure 1 alarm delay | s | 0 | 999 | |
0x01F3 | 499 | holding | u16 | A06 | High suction pressure 2 alarm delay | s | 0 | 999 | |
0x01FC | 508 | holding | u16 | A08 | Low suction pressure 2 alarm delay | s | 0 | 999 | |
0x01FA | 506 | holding | u16 | A11 | Low discharge pressure alarm delay | s | 0 | 999 | |
0x01FE | 510 | holding | u16 | A12 | Compressor thermal overload alarm delay | s | 0 | 999 | |
0x01FF | 511 | holding | u16 | A13 | Prevent time in which no compressor starts are enabled | m | 0 | 99 | |
0x01F7 | 503 | holding | u16 | A14 | Prevent time in which the activation signals the alarm | m | 0 | 999 | |
0x01FB | 507 | holding | u16 | A15 | Time to reset prevent alarm | m | 0 | 99 | |
0x01FD | 509 | holding | u16 | A20 | Alarm signal delay | s | 0 | 999 | |
0x01F0 | 496 | holding | u16 | A21 | Time to change low pressure alarm from automatic to manual | s | 0 | 999 | |
0x01F1 | 497 | input | u16 | Operating percentage of first capacity controlled compressor | |||||
0x01F4 | 500 | input | u16 | Operating percentage of second capacity controlled compressor | |||||
0x07 | 7 | coil | bool | Unit on | |||||
0x00 | 0 | discrete | bool | Status of compressor 1 | |||||
0x0D | 13 | discrete | bool | Status of compressor 2 | |||||
0x08 | 8 | discrete | bool | Status of compressor 3 | |||||
0x0B | 11 | discrete | bool | Status of compressor 4 | |||||
0x04 | 4 | discrete | bool | Status of fan 1 | |||||
0x01 | 1 | discrete | bool | Status of fan 2 | |||||
0x09 | 9 | discrete | bool | Status of fan 3 | |||||
0x0C | 12 | discrete | bool | Status of fan 4 | |||||
0x03 | 3 | discrete | bool | Status of digital input 1 | |||||
0x06 | 6 | discrete | bool | Status of digital input 2 | |||||
0x0F | 15 | discrete | bool | Status of digital input 3 | |||||
0x0A | 10 | discrete | bool | Status of digital input 4 | |||||
0x0E | 14 | discrete | bool | Status of digital input 5 | |||||
0x02 | 2 | coil | bool | A19 | Reset alarms | ||||
0x05 | 5 | coil | bool | /14 | Digital input logic | ||||
0x017 | 23 | coil | bool | /28 | Alarm relay logic | ||||
0x010 | 16 | coil | bool | /10 | Enable fan inverter | ||||
0x01D | 29 | coil | bool | /38 | ON/OFF from supervisor | ||||
0x018 | 24 | coil | bool | /32 | Enable 'prevent' control on condenser | ||||
0x01B | 27 | coil | bool | /02 | Enable management of different compressors | ||||
0x014 | 20 | coil | bool | /29 | Type of compressor reset | ||||
0x011 | 17 | coil | bool | /30 | Type of fan reset | ||||
0x019 | 25 | coil | bool | /31 | Type of reset for general high press. Switch | ||||
0x01C | 28 | coil | bool | C09 | Reset compressor 1 hours | ||||
0x013 | 19 | coil | bool | C11 | Reset compressor 2 hours | ||||
0x016 | 22 | coil | bool | C13 | Reset compressor 3 hours | ||||
0x01F | 31 | coil | bool | C15 | Reset compressor 4 hours | ||||
0x01A | 26 | coil | bool | r32 | Enable floating condenser control | ||||
0x01E | 30 | coil | bool | A22 | Enable unit Off due to probe fault | ||||
0x012 | 18 | coil | bool | /13 | Enable fan with comp on | ||||
0x015 | 21 | discrete | bool | A01 | Alarm: compressor 1 | ||||
0x027 | 39 | discrete | bool | A02 | Alarm: compressor 2 | ||||
0x020 | 32 | discrete | bool | A03 | Alarm: compressor 3 | ||||
0x02D | 45 | discrete | bool | A04 | Alarm: compressor 4 | ||||
0x028 | 40 | discrete | bool | A22 | Alarm: fan 1 | ||||
0x02B | 43 | discrete | bool | A23 | Alarm: fan 2 | ||||
0x024 | 36 | discrete | bool | A24 | Alarm: fan 3 | ||||
0x021 | 33 | discrete | bool | A25 | Alarm: fan 4 | ||||
0x029 | 41 | discrete | bool | A09 | Alarm: liquid level | ||||
0x02C | 44 | discrete | bool | A10 | Alarm: general low suction pressure 1 (from multifunction DI) | ||||
0x023 | 35 | discrete | bool | A11 | Alarm: general low suction pressure 2 (from multifunction DI) | ||||
0x026 | 38 | discrete | bool | A13 | Alarm: low discharge pressure | ||||
0x02F | 47 | discrete | bool | A14 | Alarm: high discharge pressure | ||||
0x02A | 42 | discrete | bool | A15 | Alarm: low suction pressure 1 | ||||
0x02E | 46 | discrete | bool | A16 | Alarm: high suction pressure 1 | ||||
0x022 | 34 | discrete | bool | A17 | Alarm: low suction pressure 2 | ||||
0x025 | 37 | discrete | bool | A18 | Alarm: high suction pressure 2 | ||||
0x037 | 55 | discrete | bool | A20 | Probe B1 faulty or disconnected | ||||
0x030 | 48 | discrete | bool | AB2 | Probe B2 faulty or disconnected | ||||
0x03D | 61 | discrete | bool | AB3 | Probe B3 faulty or disconnected | ||||
0x038 | 56 | discrete | bool | A19 | Probe B4 faulty or disconnected | ||||
0x03B | 59 | discrete | bool | A05 | Compressor 1 maintenance | ||||
0x034 | 52 | discrete | bool | A06 | Compressor 2 maintenance | ||||
0x031 | 49 | discrete | bool | A07 | Compressor 3 maintenance | ||||
0x039 | 57 | discrete | bool | A08 | Compressor 4 maintenance | ||||
0x03C | 60 | discrete | bool | A12 | General discharge pressure switch (from multifunction DI) | ||||
0x033 | 51 | discrete | bool | A26 | General fan thermal overload | ||||
0x036 | 54 | discrete | bool | A27 | Prevent high discharge pressure | ||||
0x03F | 63 | discrete | bool | A28 | Compressors off due to prevent | ||||
0x03A | 58 | discrete | bool | A29 | Excessive prevent frequency | ||||
0x03E | 62 | discrete | bool | HtE | High outside temperature | ||||
0x032 | 50 | discrete | bool | HtA | High room temperature |
Общие регистры
Адрес | Параметры регистра | Описание | Значения | |||
---|---|---|---|---|---|---|
Dec | Hex | Тип | Доступ | Формат | ||
104-105 | 0x0068 - 0x0069 | Input | RO | u32 | Время работы с момента загрузки | секунды |
121 | 0x0079 | Input | RO | u16 | Текущее напряжение питания | мВ |
110 | 0x006E | Holding | RW | u16 | Скорость порта RS-485. Настройка параметров подключения по RS-485 |
x100, Боды 12 — 1200 бит/с, 24 — 2400 бит/с, 48 — 4800 бит/с, 96 — 9600 бит/с, 192 — 19 200 бит/с, 384 — 38 400 бит/с, 576 — 57 600 бит/с, 1152 — 115 200 Кбит/с |
111 | 0x006F | Holding | RW | u16 | Настройка бита чётности порта RS-485 | 0 — нет бита чётности (none), 1 — нечётный, 2 — чётный |
112 | 0x0070 | Holding | RW | u16 | Количество стоп-битов порта RS-485 | 1, 2 |
113 | 0x0071 | Holding | RW | u16 | Время перед отправкой ответа на modbus запрос | 0 - 254 мс |
114 | 0x0072 | Holding | RW | u16 | Режим непрерывного чтения регистров с зазором | 0 - отключен 1 - включен 2 - включение сохраняется после перезагрузки |
128 | 0x0080 | Holding | RW | u16 | Modbus-адрес устройства (подробнее) | |
120 | 0x0078 | Holding | RW | u16 | Перезагрузка устройства без сохранения состояния | любое, отличное от 0 перезагружает устройство |
129 | 0x0081 | Holding | RW | u16 | Перевод в режим обновления прошивки на 2 минуты | любое, отличное от 0 переводит устройство в режим обновления прошивки |
130 | 0x0082 | Holding | RW | u8 | Отключение индикатора состояния | 0 - активен, 1 - отключен |
123 | 0x007B | Input | RO | u16 | Напряжение на микроконтроллере | мВ |
124 | 0x007C | Input | RO | u16 | Внутренняя температура микроконтроллера | x0.1, °C |
200-205 | 0x00C8 - 0x00CD | Input | RO | string | Модель устройства | |
206-219 | 0x00CE - 0x00DB | Input | RO | string | Расширение модели устройства. Для новых устройств WB-LED и WB-MAI6 поле поддерживается изначально, для остальных - в прошивках с "быстрым Modbus". Для чтения модели устройства нужно читать диапазон из 20 регистров (200 - 219). Если устройство возвращает ошибку Illegal Data Address - читать 6 регистров (200 - 205). | |
220-248 | 0x00DC - 0x00F8 | Input | RO | string | Хэш коммита и название ветки откуда собрана прошивка (2 символа в регистре) | |
250-265 | 0x00FA - 0x0109 | Input | RO | string | Версия прошивки | |
266-269 | 0x010A - 0x010D | Input | RO | u64 | Расширение серийного номера | |
270-271 | 0x010E - 0x010F | Input | RO | u32 | Серийный номер | |
290-301 | 0x0122 - 0x012D | Holding | RO | string | Сигнатура прошивки | |
330-336 | 0x014A - 0x0150 | Holding | RO | string | Версия загрузчика |
Версия прошивки в устройствах с «Быстрым Modbus»
В устройствах, поддерживающих Быстрый Modbus, используется другой формат обозначения версии прошивки.
- Диапазон регистров «Модель устройства» расширен до 20 регистров.
- Версия формируется согласно semver и имеет формат
MAJOR.MINOR.PATCH
с опциональным суффиксом(-rc|+wb)SUFFIX
:- суффикс
-rc
означает, что прошивка предназначена для тестирования и может быть нестабильной. Хранится в регистре с отрицательным знаком; - суффикс
+wb
добавляется, когда к прошивке, зафиксированной в релизе, требуется выпустить фикс. Хранится в регистре с положительным знаком.
- суффикс
- Цифры версии доступны по отдельности в формате u16 (для суффикса - s16), регистры 320-323.
- Доступно число u32, содержащее комбинацию цифр версии и позволяющее за одно сравнение понять, увеличилась или уменьшилась версия прошивки:
- число рассчитывается по формуле
if (SUFFIX >= 0) { SUFFIX = SUFFIX + 128; } else { SUFFIX = -1 - SUFFIX; } VERSION = (MAJOR << 24) + (MINOR << 16) + (PATCH << 8) + SUFFIX;
- число доступно для чтения в little-endian и big-endian форматах;
- число для более свежей версии всегда будет больше, чем для предыдущей, в том числе, когда прошивка переходит из тестовой в стабильную.
- Таким образом обеспечивается корректное сравнение версий:
1.2.3-rc1 < 1.2.3-rc10 < 1.2.3 < 1.2.3+wb1 < 1.2.3+wb10.
Адрес | Параметры регистра | Описание | Значения | |||
---|---|---|---|---|---|---|
Dec | Hex | Тип | Доступ | Формат | ||
200-219 | 0x00C8 - 0x00DB | Input | RO | string | Модель устройства | |
320 | 0x0140 | Input | RO | u16 | Версия прошивки в числовом формате | MAJOR |
321 | 0x0141 | MINOR | ||||
322 | 0x0142 | PATCH | ||||
323 | 0x0143 | s16 | SUFFIX | |||
324-325 | 0x0144 - 0x0145 | Input | RO | u32 | Версия прошивки в числовом формате | |
326-327 | 0x0146 - 0x0147 | Input | RO | u32 | Версия прошивки в Big Endian формате |
| 816-818 || 0x0330 - 0x0332 || Input || RO || u16 || Используются для определения модели контроллера || |- |}