Using Wiren Board with peripheral devices/en: различия между версиями
FuzzyBot (обсуждение | вклад) м (FuzzyBot переименовал страницу Connecting peripheral devices/en в Using Wiren Board with peripheral devices/en без оставления перенаправления: Часть переводимой страницы Connecting peripheral devices.) |
Fizikdaos (обсуждение | вклад) (Новая страница: «Some counters have a pulse output to optocoupler, then two wires have the correct polarity - "plus" and "minus". In this case, minus connected to GND, and the "pl…») |
||
(не показаны 34 промежуточные версии 3 участников) | |||
Строка 19: | Строка 19: | ||
For overvoltage protection controller integrated protective diodes - external protective elements are not required. | For overvoltage protection controller integrated protective diodes - external protective elements are not required. | ||
Also for low-voltage load switching, you can use digital output module (WBIO-DO-HS-8), see. [[Special:MyLanguage/ | Also for low-voltage load switching, you can use digital output module (WBIO-DO-HS-8), see. [[Special: MyLanguage / O Modules | Modules IO]]. | ||
Строка 43: | Строка 43: | ||
Also for the connection of current sensors designed special [[ | Also for the connection of current sensors designed special [[Wiren Board 5: Модуль расширения ADC | extension module]]. | ||
Строка 56: | Строка 56: | ||
For a more accurate measurement of resistance, as well as to connect Pt100, Pt1000 and for two- and three-wire circuit | For a more accurate measurement of resistance, as well as to connect Pt100, Pt1000 and for two- and three-wire circuit | ||
is a special [[ | is a special [[Wiren Board 5: Extension Module ADC | extension module]]. | ||
Строка 70: | Строка 70: | ||
* With Ax terminal controller. Connect one wire to the power supply 5-24V, the second wire to the terminal Ax. | * With Ax terminal controller. Connect one wire to the power supply 5-24V, the second wire to the terminal Ax. | ||
* Using input-output module WBIO-DI-DR-8 (8 channels), see. [[Special: MyLanguage/ | * Using input-output module WBIO-DI-DR-8 (8 channels), see. [[Special: MyLanguage / O Modules | IO Modules ]]. One of the wires connected to GND, the second to terminal Dx of module. | ||
* Using extension module [[Special: MyLanguage/WBE-DI-DR-3|WBE-DI-DR-3]] (3 channels). One of the wires connected to GND, the second terminal of the Ox in the corresponding expansion module. | * Using extension module [[Special: MyLanguage / WBE-DI-DR-3 | WBE-DI-DR-3]] (3 channels). One of the wires connected to GND, the second terminal of the Ox in the corresponding expansion module. | ||
* Can be connected to the inputs Rx controller, including internal current source. One of the wires connected to GND, the second to the Rx controller. | * Can be connected to the inputs Rx controller, including internal current source. One of the wires connected to GND, the second to the Rx controller. | ||
Строка 82: | Строка 82: | ||
== | == Устройства с выходом открытый коллектор == | ||
Строка 88: | Строка 88: | ||
Устройство и контроллер '''должны иметь общую землю'''. | |||
Есть несколько способов подключить такие устройства к контроллеру: | |||
* | * С помощью модуля ввода-вывода WBIO-DI-DR-8 (8 каналов), см. [[Special:MyLanguage/Модули ввода-вывода|Модули ввода-вывода]]. Выход "открытый коллектор" подключите к клемме Dx модуля. | ||
* | * С помощью модуля расширения [[Special:MyLanguage/WBE-DI-DR-3|WBE-DI-DR-3]] (3 канала). Выход "открытый коллектор" подключите к клемме Ox соответствующей модулю расширения. | ||
* | * Можно подключить к входам R1 и R2 контроллера, включив внутренний источник тока. | ||
== | == Контакторы с управляющим напряжением 220В == | ||
Используйте модуль расширения с релейными выходами, например [[Special:MyLanguage/Модули ввода-вывода#Модуль релейных выходов (WBIO-DO-R3A-8)|WBIO-DO-R3A-8]]. | |||
Подключите управляющую катушку контактора через реле модуля расширения (см. рисунок). | |||
Модуль расширения содержит TVS, защищающий контакты реле от искрения. Внешние защитные компоненты не требуются. | |||
== | == Подключение к 1-Wire сети == | ||
Землю сети подключите к клемме GND или общей земляной шине. | |||
Линию данных к клемме 1-Wire. | |||
Линию питания к клемме 5Vout (внутренний источник питания). | |||
Допускается использовать внешние источники питания шины 1-Wire. | |||
При использовании пассивного питания, контакт питания каждого датчика соединяется с земляным проводом. | |||
В этом случае, шина прокладывается двумя проводами, подключаемыми соответственно к "1-Wire" и "GND". | |||
== | == Подключение к сети RS-485 == | ||
Смотрите [[Special:MyLanguage/RS-485|RS-485]]. | |||
Wiren Board 5 | В Wiren Board 5 есть два порта RS-485. Второй порт мультиплексирован с портом CAN (L c A, H c B) | ||
Линии А В подключаются к клеммам А и В соответственно. Сигнальную землю (если есть) подключить к земле контроллера. | |||
Если сеть RS-485 достаточно протяженная, то для её подключения рекомендуется использовать [[Wiren Board 5: Модуль расширения RS485-ISO|модуль расширения с гальванически-изолированным RS-485]]. | |||
Строка 147: | Строка 147: | ||
=== | === Пример подключения устройств === | ||
Схема испытательного стенда - [[Файл:Стенд-hi.jpg|thumb|500px|Схема стенда]] |
Версия 16:04, 15 января 2016
Switching low-voltage load
Examples: 12/24V relay , LED, fans, signal lamps and so on.
Connect '+' load to "+" power supply, and "-" to terminal Ax.
If the total current per channel over 2 A connect GND terminal to the "-" power supply.
When switching inductive loads (relay), there are voltage spikes.
For overvoltage protection controller integrated protective diodes - external protective elements are not required.
Also for low-voltage load switching, you can use digital output module (WBIO-DO-HS-8), see. Modules IO.
Sensors with analog voltage output
Example: temperature sensors.
Connect the device to a terminal GND or to a common ground. The sensor output is connected to one of the terminals Ax or Rx. Channels Ax / Rx have different ranges of the measured voltages. Choose the the best channel for your sensor.
Sensors with analog current output
Special current inputs in the WB absent but it is possible, using a resistor Rx = 100-300Om, the current is converted into a voltage and connect as in the previous.
Also for the connection of current sensors designed special extension module.
Resistive Sensors
Inputs Rx are designed to measure resistance in the range 1-100kOm. Measured resistance is connected between the GND and Rx.
For a more accurate measurement of resistance, as well as to connect Pt100, Pt1000 and for two- and three-wire circuit
is a special extension module.
Sensors / meters with pulse output / button
These devices form a signal by closing two wires.
Connection Methods to the controller:
- With Ax terminal controller. Connect one wire to the power supply 5-24V, the second wire to the terminal Ax.
- Using input-output module WBIO-DI-DR-8 (8 channels), see. IO Modules . One of the wires connected to GND, the second to terminal Dx of module.
- Using extension module WBE-DI-DR-3 (3 channels). One of the wires connected to GND, the second terminal of the Ox in the corresponding expansion module.
- Can be connected to the inputs Rx controller, including internal current source. One of the wires connected to GND, the second to the Rx controller.
Some counters have a pulse output to optocoupler, then two wires have the correct polarity - "plus" and "minus".
In this case, minus connected to GND, and the "plus" to the input.
Or "plus" to the power supply, negative to Ax (first method).
Устройства с выходом открытый коллектор
Устройство и контроллер должны иметь общую землю.
Есть несколько способов подключить такие устройства к контроллеру:
- С помощью модуля ввода-вывода WBIO-DI-DR-8 (8 каналов), см. Модули ввода-вывода. Выход "открытый коллектор" подключите к клемме Dx модуля.
- С помощью модуля расширения WBE-DI-DR-3 (3 канала). Выход "открытый коллектор" подключите к клемме Ox соответствующей модулю расширения.
- Можно подключить к входам R1 и R2 контроллера, включив внутренний источник тока.
Контакторы с управляющим напряжением 220В
Используйте модуль расширения с релейными выходами, например WBIO-DO-R3A-8.
Подключите управляющую катушку контактора через реле модуля расширения (см. рисунок).
Модуль расширения содержит TVS, защищающий контакты реле от искрения. Внешние защитные компоненты не требуются.
Подключение к 1-Wire сети
Землю сети подключите к клемме GND или общей земляной шине. Линию данных к клемме 1-Wire. Линию питания к клемме 5Vout (внутренний источник питания). Допускается использовать внешние источники питания шины 1-Wire.
При использовании пассивного питания, контакт питания каждого датчика соединяется с земляным проводом.
В этом случае, шина прокладывается двумя проводами, подключаемыми соответственно к "1-Wire" и "GND".
Подключение к сети RS-485
Смотрите RS-485.
В Wiren Board 5 есть два порта RS-485. Второй порт мультиплексирован с портом CAN (L c A, H c B)
Линии А В подключаются к клеммам А и В соответственно. Сигнальную землю (если есть) подключить к земле контроллера.
Если сеть RS-485 достаточно протяженная, то для её подключения рекомендуется использовать модуль расширения с гальванически-изолированным RS-485.
Пример подключения устройств
Схема испытательного стенда -