WBC-4G v.2/en: различия между версиями
(Новая страница: «{{Wbincludes:Configuration WBC}}») |
|||
(не показаны 22 промежуточные версии этого же участника) | |||
Строка 2: | Строка 2: | ||
[[File:WBC-4G v2.png|300px|thumb|right|Front side of | [[File:WBC-4G v2.png|300px|thumb|right| Front side of WBC-4G v.2 module for WB6 and WB7]] | ||
{{PDF}} | {{PDF}} | ||
'''[https://wirenboard.com/en/product/wbc-4g-v2/ Buy | '''[https://wirenboard.com/en/product/wbc-4g-v2/ Buy online]''' | ||
== Description == | == Description == | ||
WBC-4G v.2 | WBC-4G v.2 - suitable for Wiren Board 6.7-6.9 and 7.x, unlike v.1 - an enlarged cutout from the bottom. | ||
{{Wbincludes:WBC-4G Specifications}} | {{Wbincludes:WBC-4G Specifications}} | ||
== Module | == Module installation == | ||
[[File:WB7+Modem.png|300px|thumb|right| WBC-4G v.2 module | [[File:WB7+Modem.png|300px|thumb|right| Installing the WBC-4G v.2 module in the Wiren Board 7 controller]] | ||
{{Wbincludes:Setup MOD}} | {{Wbincludes:Setup MOD}} | ||
#Insert the SIM card | #Insert the SIM card | ||
# | #Reassemble the case. | ||
#Screw the external antenna onto | #Screw the external antenna onto SMA female. | ||
When mounting in a | When mounting in a metal shield, position the antenna outside for reliable radio communication. | ||
== Configuration == | == Configuration == | ||
Строка 23: | Строка 23: | ||
{{Wbincludes:Configuration WBC}} | {{Wbincludes:Configuration WBC}} | ||
== | == Info == | ||
{{Wbincludes:WBC-4G Info}} | {{Wbincludes:WBC-4G Info}} | ||
== | == Setting up an Internet connection == | ||
See the instructions for setting up the Internet via a 4G modem in the article [[GSM/GPRS#Internet with a 4G modem (LTE)|GSM/GPRS]]. | |||
You need to consider what exactly is 4G The network does not work in all regions. | |||
Check current <code>AT+CNMP?</code> | |||
Switching modem to automatic network selection mode is | Switching the modem to the automatic network type selection mode is carried out by the command: <code>AT+CNMP=2</code> | ||
==Documentation== | ==Documentation== | ||
AT commands: | AT commands: | ||
* [[File:A7600_Series_AT_Command_Manual_V1.02.pdf]] for | * [[File:A7600_Series_AT_Command_Manual_V1.02.pdf]] for pre-B05 chips; | ||
* [[File:A76XX_Series_AT_Command_Manual_V1.07.pdf]] for versions B05 and newer. | * [[File:A76XX_Series_AT_Command_Manual_V1.07.pdf]] for versions B05 and newer. | ||
You can find out the chip version number with the AT command <code>at+cgmr</code> , which returns a string with the number, characters 6 to 8 will be the chip version. [[GSM/GPRS#Sending AT commands| How to send an AT command]]. | |||
For example, in the | For example, in the example below, the chip version is B05: | ||
<syntaxhighlight lang="at"> | <syntaxhighlight lang="at"> | ||
at+cgmr | at+cgmr | ||
+CGMR: A39C4B05A7600M7 | +CGMR: A39C4B05A7600M7 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
[[Modem a76xx flashing| SIMCom A76xxE-H | [[Modem a76xx flashing| Instructions for flashing modems SIMCom A76xxE-H]] | ||
==Known | ==Known Issues== | ||
No known issues. | |||
== Device revisions == | == Device revisions == | ||
Строка 72: | Строка 72: | ||
| | | | ||
*Fixed board geometry for compatibility with WB7, minor board routing changes | *Fixed board geometry for compatibility with WB7, minor board routing changes | ||
|- | |-! N!|} | ||
|} | |||
== Images and device | == Images and drawings of the device == | ||
<gallery mode="packed" heights="150px"> | <gallery mode="packed" heights="150px"> | ||
Image:WBC-4G v2.png | Front side of the | Image: WBC-4G v2.png | Front side of the WBC-4G v.2 module for WB6 and WB7 | ||
Image:WBC-4G bot v2.png | | Image: WBC-4G bot v2.png | The reverse side of the WBC-4G v.2 module for WB6 and WB7 | ||
</gallery> | </gallery> |
Версия 23:12, 30 мая 2023
Buy online
Description
WBC-4G v.2 - suitable for Wiren Board 6.7-6.9 and 7.x, unlike v.1 - an enlarged cutout from the bottom.
Parameter | Value |
---|---|
Operating frequency ranges |
LTE-FDD B1, B3, B5, B7, B8, B20 LTE-TDD B38, B40 UMTS/HSPA 900/2100 MHz (B1, B8) GSM/GPRS/EDGE 900/1800 MHz |
Data transfer rate |
FDD-LTE Cat4 - up to 150 Mbps (download), up to 50 Mbps (upload) TDD-LTE Cat4 - up to 130 Mbps (download), up to 35 Mbps (upload). HSPA+ - up to 42 Mbps (download), up to 5.76 Mbps (upload) WCDMA - up to 384 kbit/s (downloading), up to 384 kbit/s (uploading) EDGE - up to 236.8 kbit/s (download). GPRS - up to 85.6 kbit/s (download), up to 85.6 kbit/s (upload). |
Sending SMS messages | Supported |
Voice calls | Not supported |
SIM cards | 2 pieces, nano-SIM |
SIM card modes | Alternating |
Antenna connector | SMA |
Power supply voltage | 5 V |
Power consumption |
|
Module installation
When ordering modules bundled with the Wiren Board controller, we install them in production - you only need to configure the modules in web interface of the controller.
If you bought the modules separately, install them yourself:
- Disassemble the controller case.
- Insert the module, observing the polarity: the protrusion on it must fit into the groove on the controller board.
- Insert the SIM card
- Reassemble the case.
- Screw the external antenna onto SMA female.
When mounting in a metal shield, position the antenna outside for reliable radio communication.
Configuration
After physically connecting the modem, it should be added to the controller configuration:
- In the web interface, go to the Settings → Configs → Hardware Modules Configuration section, select the Modem slot.
- In the Module type drop-down list, select the type of the installed module.
- Click the Save button. The controller will enable the ports required for the modem to work.
To remove the module, select the type None.
After configuring, turn on the modem using the command wb-gsm on
and set up the connection to the mobile operator.
Info
Обмен данными с модулем идет через последовательные порты /dev/ttyGSM
и /dev/ttyUSBx (обычно это /dev/ttyUSB0
и /dev/ttyUSB1
).
Value | Parameter | Description |
---|---|---|
Auto-bauding | Baud rate | Speed, bit/s. Set to 115200 in the connection program settings.
After connecting, send |
8 | Data bits | Number of data bits |
None | Parity | Parity bit |
1 | Stop bits | Number of stop bits |
Off | Hardware flow control | Hardware flow control |
Off | Software flow control | Software flow control |
При необходимости параметры соединения можно изменить через AT команды.
Setting up an Internet connection
See the instructions for setting up the Internet via a 4G modem in the article GSM/GPRS.
You need to consider what exactly is 4G The network does not work in all regions.
Check current AT+CNMP?
Switching the modem to the automatic network type selection mode is carried out by the command: AT+CNMP=2
Documentation
AT commands:
- Файл:A7600 Series AT Command Manual V1.02.pdf for pre-B05 chips;
- Файл:A76XX Series AT Command Manual V1.07.pdf for versions B05 and newer.
You can find out the chip version number with the AT command at+cgmr
, which returns a string with the number, characters 6 to 8 will be the chip version. How to send an AT command.
For example, in the example below, the chip version is B05:
at+cgmr
+CGMR: A39C4B05A7600M7
Instructions for flashing modems SIMCom A76xxE-H
Known Issues
No known issues.
Device revisions
The batch number can be found on a sticker on the side of the case or on the PCB.
Images and drawings of the device
Revision | Batch | Release date | Differences from previous revision |
---|---|---|---|
2.1 | v2.1A/1, v2.1A, v2.1B, v2.1D/1, v2.1D/2, v2.1G, v2.1G/1 - ... | 11.2022 - ... |
|
1.10 | v1.10A, v1.10B, v1.10C, v1.10C/2 | 04.2022 - 12.2022 |
|
1.9 | v1.9A, v1.9B, v1.9B/2 | 12.2021 - 06.2022 |
|