Перейти к содержанию

Навигация

Wiren Board: Extension Modules/en: различия между версиями

м
FuzzyBot переименовал страницу Wiren Board 6: Extension Modules/en в Wiren Board: Extension Modules/en без оставления перенаправления: Часть переводимой страницы Wiren Board 6: Extension Modules.
(Новая страница: «If the modules were purchased separately and you are installing them yourself, you need to: #Remove the bottom cover of the controller enclosure. #Remove the main…»)
м (FuzzyBot переименовал страницу Wiren Board 6: Extension Modules/en в Wiren Board: Extension Modules/en без оставления перенаправления: Часть переводимой страницы Wiren Board 6: Extension Modules.)
 
(не показано 17 промежуточных версий 1 участника)
Строка 21: Строка 21:
|-
|-
|WBE2-I-RS232
|WBE2-I-RS232
|[[Служебная:MyLanguage/Wiren Board 6: Модуль расширения RS-232/en| RS-232 Extension module]]
|[[Wiren_Board_6:_Модуль_расширения_RS-232_(WBE2-I-RS232)/en| RS-232 Extension module]]
|RS-232
|RS-232
|1
|1
Строка 27: Строка 27:
|-
|-
|WBE2-I-CAN-ISO
|WBE2-I-CAN-ISO
|[[Служебная:MyLanguage/Wiren_Board_6:_Модуль_расширения_CAN_(WBE-I-CAN-ISO)| CAN-ISO Extension module]]
|[[Wiren_Board_6:_Модуль_расширения_CAN_(WBE2-I-CAN-ISO)/en| CAN-ISO extension module]]
|CAN, UART-CAN
|CAN, UART-CAN
|1
|1
Строка 33: Строка 33:
|-
|-
|WBE2-I-RS485-ISO
|WBE2-I-RS485-ISO
|[[Служебная:MyLanguage/Wiren Board 6: Модуль расширения RS485-ISO/en|Extension module RS-485-ISO]]
|[[Wiren_Board_6:_Модуль_расширения_RS485-ISO_(WBE2-I-RS485-ISO)/en| RS-485-ISO extension module]]
|RS-485
|RS-485
|1
|1
Строка 39: Строка 39:
|-
|-
|WBE2-I-1-WIRE
|WBE2-I-1-WIRE
|[[Служебная:MyLanguage/Wiren Board 6: Модуль расширения 1-Wire/en|1-Wire Extension module]]
|[[Wiren_Board_6:_Модуль_расширения_1-Wire/en|1-Wire extension module]]
|1-Wire
|1-Wire
|1
|1
Строка 45: Строка 45:
|-
|-
|WBE2-I-KNX
|WBE2-I-KNX
|[[Служебная:MyLanguage/Wiren Board 6: Модуль расширения KNX (WBE2-I-KNX)/en| KNX Extension module ]]
|[[KNX_Module_for_WB6_(WBE2-I-KNX)/en| KNX extension module]]
|KNX
|KNX
|1
|1
Строка 53: Строка 53:
|-
|-
|WBE2-DI-DR-3
|WBE2-DI-DR-3
|[[Wiren_Board_6:_Модуль_расширенияWBE-DI-DR-3/en|Dry contact extension module]]
|[[Wiren_Board_6:_Модуль_расширения_"сухие_контакты"_(WBE2-DI-DR-3)/en|Dry contact extension module]]
|dry contact
|dry contact
|3
|3
Строка 62: Строка 62:


|WBE2-DO-R6C-1
|WBE2-DO-R6C-1
|[[Wiren_Board_6:_Модуль_релейных_выходов_WBE-DO-R6C-1|Модуль релейных выходов]]
|[[Wiren_Board_6:_Модуль_релейных_выходов_(WBE2-DO-R6C-1)/en|Relay outputs module]]
|механическое реле
|relay
|1
|1
|3 kV
|3 kV
|-
|-
|WBE2-DO-SSR-2
|WBE2-DO-SSR-2
|[[Wiren_Board_6:_Модуль_выходов_"сухой_контакт"_(оптореле)_WBE-DO-SSR-2|Модуль выходов "сухой контакт" (оптореле)]]
|[[Wiren_Board_6:_Модуль_выходов_"сухой_контакт"_(оптореле)_(WBE2-DO-SSR-2)/en|Solid state relay module]]
|оптореле
|solid state relay
|2
|2
|нет
|no
|-
|-
|WBE2-DO-OC-2
|WBE2-DO-OC-2
|[[Wiren_Board_6:_Модуль_выходов_"Открытый_коллектор"_WBE-DO--2|Модуль выходов "Открытый коллектор"]]
|[[Wiren_Board_6:_Модуль_выходов_"Открытый_коллектор"_(WBE2-DO-OC-2)/en|Open collector outputs module]]
|открытый коллектор
|open collector
|2
|2
|нет
|no
|-
|-
! colspan="5" | аналогового ввода-вывода
! colspan="5" | analog input-output
|-
|-
|WBE2-AO-10V-2
|WBE2-AO-10V-2
|[[Служебная:MyLanguage/Wiren Board 6: Модуль расширения DAC (WBE2-AO-10V-2)| Двухканальный модуль расширения ЦАП]] — 2 выхода напряжения (0 — 10 В)
|[[Служебная:MyLanguage/Wiren Board 6: Модуль расширения DAC (WBE2-AO-10V-2)/en| Dual-channel module with 0-10V DAC analog outputs]] — 2 voltage outputs (0 — 10 V)
|аналоговые выходы
|analog outputs
|2
|2
|нет
|no
|-
|-
! colspan="5" | прочие
! colspan="5" | other
|-
|-
|WBE2S-MICROSD
|WBE2S-MICROSD
|[[Служебная:MyLanguage/Wiren_Board_6:_WBE2S-MICROSD_Extension_Module| Модуль расширения microSD]]
|[[Служебная:MyLanguage/Wiren_Board_6:_WBE2S-MICROSD_Extension_Module/en| microSD extension module]]
|
|
|
|
Строка 96: Строка 96:
|-
|-
|WBE2R-R-GPS
|WBE2R-R-GPS
|[[Служебная:MyLanguage/Wiren Board 6: Модуль расширения GPS/Glonass (WBE2R-R-GPS)| Модуль расширения GPS/Glonass]]
|[[Wiren_Board_6:_WBE2R-R-GPS_GPS/GLONASS_Extension_Module/en| GPS/Glonass extension module]]
|
|
|
|-
|WBE2R-R-ZIGBEE
|[[Служебная:MyLanguage/WBE2R-R-ZIGBEE/en| ZigBee extension module]]
|
|
|
|
Строка 102: Строка 108:
|-
|-
|WBE2S-R-433MHZ
|WBE2S-R-433MHZ
|[[Служебная:MyLanguage/Wiren_Board_6:_Модуль_расширения_433MHz_(WBE2S-R-433MHZ)| Модуль расширения 433MHz]]
|[[Wiren_Board_6:_Модуль_расширения_433MHz_(WBE2S-R-433MHZ)/en| 433MHz extension module]]
|
|
|
|
Строка 124: Строка 130:




== Совместимость модулей и разъёмов ==
==Module and connector compatibility==
==Module and connector compatibility==
The Wiren Board 6 has three connectors for extension modules of two different types:
The Wiren Board 6 has three connectors for extension modules of two different types:
Строка 149: Строка 154:
|}
|}


For example, WBE2S-MICROSD can be installed only in slot MOD3, and WBE2R-R-GPS — in any slot.
'''For example''', WBE2S-MICROSD can be installed only in slot MOD3, and WBE2R-R-GPS — in any slot.


===Installation===
===Installation===
Строка 160: Строка 165:
#Insert the module, observing polarity, the tab on the module should fit into the slot on the controller board.
#Insert the module, observing polarity, the tab on the module should fit into the slot on the controller board.


Расширенная информация по установке приводятся в описании каждого модуля по ссылкам из таблицы [[#Список модулей расширения для контроллеров Wiren Board 6|"Модули расширения интерфейсов"]].
Each module description contains the detailed information for installation.The description is given in the  [[#List|List of extension modules]] table.


==Configuration==
==Configuration==


After the physical connection, you need  to configure it in the controller interface. To do this, go to the '''Hardware Modules Configuration''' section of the web interface, select one of the three extension slots (Internal slot 1, 2 or 3) and select the type of the installed module from the '''Module type''' dropdown list. Click '''Save''': the module is installed and ready to use. To remove a module, select '''None'''. Click '''Save'''.
After the physical connection, you need  to configure it in the controller interface. To do this, go to the '''Hardware Modules Configuration''' section of the web interface, select one of the three extension slots (Internal slot 1, 2 or 3) and select the type of the installed module from the '''Module type''' dropdown list. Click '''Save''': the module is installed and ready to use. To remove a module, select '''None'''. Click '''Save'''.
wb_editors
14 355

правок