Модуль релейных выходов 3A (WBIO-DO-R3A-8)/en: различия между версиями
(Новая страница: «Contains 8 relays. Two of them are rocker (NO/COM/NC) switching corresponding 8 outputs. The outputs are output to screw clamps designed for a maximum current of…») |
(Новая страница: «400px|thumb|none|Connection scheme») |
||
(не показано 9 промежуточных версий этого же участника) | |||
Строка 9: | Строка 9: | ||
Contains 8 relays. Two of them are rocker (NO/COM/NC) switching corresponding 8 outputs. The outputs are output to screw clamps designed for a maximum current of 20 A. | Contains 8 relays. Two of them are rocker (NO/COM/NC) switching corresponding 8 outputs. The outputs are output to screw clamps designed for a maximum current of 20 A. | ||
Permissible current: up to 3A per channel. | |||
Our detailed article in russian on habr.com about the choice of relay parameters for the switched load: https://habr.com/ru/company/wirenboard/blog/422197/ | |||
{| class="wikitable" | {| class="wikitable" | ||
! | !Parameter | ||
! colspan="2" | | ! colspan="2" |Value | ||
|- | |- | ||
| | |Number of outputs | ||
| colspan="2" |8 | | colspan="2" |8 | ||
|- | |- | ||
| | |Output type | ||
| colspan="2" | | | colspan="2" |mechanical relay | ||
|- | |- | ||
| rowspan="2" | | | rowspan="2" |contact Configuration | ||
|K2-K7 | |K2-K7 | ||
|SPST, | |SPST, normally open | ||
states: | |||
* | * off | ||
* | * C is closed and NO | ||
|- | |- | ||
|K1, K8 | |K1, K8 | ||
|SPDT ( | |SPDT (contacts K, NO, NC) | ||
conditions: | |||
* | * C and NS closed | ||
* | * C and NO closed | ||
|- | |- | ||
| | |Maximum switching voltage, alternating current | ||
| colspan="2" |250 | | colspan="2" |250 V | ||
|- | |- | ||
| | |Maximum switching voltage, direct current | ||
| colspan="2" |30 | | colspan="2" |30 V | ||
|- | |- | ||
| | |Maximum switching current, per channel (*) | ||
| colspan="2" |3 | | colspan="2" |3 A | ||
|- | |- | ||
| | |The channel resistance in the open state | ||
| colspan="2" |< 100 | | colspan="2" |< 100 megohms | ||
|- | |- | ||
| | |Voltage isolation between the controller and the output | ||
| colspan="2" |1500 | | colspan="2" |1500 V (RMS.) | ||
|- | |- | ||
| | |Lifetime: number of switches | ||
for 10 A 230 V AC load, cos φ = 1 | |||
| colspan="2" |100 000 | | colspan="2" |100 000 | ||
|- | |- | ||
| | |Module type | ||
| colspan="2" |"O" (non-inverted address scheme) | | colspan="2" |"O" (non-inverted address scheme) | ||
|- | |- | ||
| | |Maximum power consumption | ||
| colspan="2" | | | colspan="2" |1W | ||
|- | |- | ||
| | |Width, DIN units | ||
| colspan="2" |3 | | colspan="2" |3 | ||
|- | |- | ||
| | |Size | ||
| colspan="2" |53,3x90,2x57,5 | | colspan="2" |53,3x90,2x57,5 mm | ||
|} | |} | ||
<nowiki>*</nowiki>) | <nowiki>*</nowiki>) Maximum switching current is specified for 230 VAC resistive load. | ||
[[File:DIN 3U.png |300px|thumb|right| | [[File:DIN 3U.png |300px|thumb|right|Dimensions]] | ||
== | == Connection to the controller == | ||
See [[Модули ввода-вывода/en#Activating the modules in the controller web interface|Activating the modules in the web interface of the controller]]. In the Module type field, select '''WBIO-DO-RxA-8: 8 Channel Relay I/O module'''. In the web interface the relay will be presented by the controls of EXT'''x'''_R3A1 — EXT'''x'''_R3A8 of the Discrete I/O devices. The corresponding MQTT-topics: /devices/wb-gpio/controls/EXT'''x'''_R3A'''y'''. | |||
[[File:Wbio-do-rxa-8_controls.png|300px|thumb|right| | [[File:Wbio-do-rxa-8_controls.png|300px|thumb|right|Controls of the module in the web interface]] | ||
== | == Load connection== | ||
Relays are connected in a phase break. | |||
[[Файл:Relay outputs.png|400px|thumb|none| | [[Файл:Relay outputs.png|400px|thumb|none|Connection scheme]] |
Текущая версия на 15:28, 15 июля 2019
Purpose
Control of contactors, warning lights, etc.
Technical specifications
Contains 8 relays. Two of them are rocker (NO/COM/NC) switching corresponding 8 outputs. The outputs are output to screw clamps designed for a maximum current of 20 A.
Permissible current: up to 3A per channel.
Our detailed article in russian on habr.com about the choice of relay parameters for the switched load: https://habr.com/ru/company/wirenboard/blog/422197/
Parameter | Value | |
---|---|---|
Number of outputs | 8 | |
Output type | mechanical relay | |
contact Configuration | K2-K7 | SPST, normally open
states:
|
K1, K8 | SPDT (contacts K, NO, NC)
conditions:
| |
Maximum switching voltage, alternating current | 250 V | |
Maximum switching voltage, direct current | 30 V | |
Maximum switching current, per channel (*) | 3 A | |
The channel resistance in the open state | < 100 megohms | |
Voltage isolation between the controller and the output | 1500 V (RMS.) | |
Lifetime: number of switches
for 10 A 230 V AC load, cos φ = 1 |
100 000 | |
Module type | "O" (non-inverted address scheme) | |
Maximum power consumption | 1W | |
Width, DIN units | 3 | |
Size | 53,3x90,2x57,5 mm |
*) Maximum switching current is specified for 230 VAC resistive load.
Connection to the controller
See Activating the modules in the web interface of the controller. In the Module type field, select WBIO-DO-RxA-8: 8 Channel Relay I/O module. In the web interface the relay will be presented by the controls of EXTx_R3A1 — EXTx_R3A8 of the Discrete I/O devices. The corresponding MQTT-topics: /devices/wb-gpio/controls/EXTx_R3Ay.
Load connection
Relays are connected in a phase break.