WBE2-I-1-WIRE 1-Wire Extension Module/en: различия между версиями
(Новая страница: «In the Internal slot 1 or 2 section (depending on the slot number) select "WBE2-I-1-WIRE" and click Save.») |
(Новая страница: «The device is detected immediately, no reboot is required. After adding the device the output of the dmesg command will display a message <code>i2c-gpio mod1_i2c:…») |
||
Строка 29: | Строка 29: | ||
In the Internal slot 1 or 2 section (depending on the slot number) select "WBE2-I-1-WIRE" and click Save. | In the Internal slot 1 or 2 section (depending on the slot number) select "WBE2-I-1-WIRE" and click Save. | ||
The device is detected immediately, no reboot is required. After adding the device the output of the dmesg command will display a message <code>i2c-gpio mod1_i2c: using pins 24 (SDA) and 25 (SCL)</code> | |||
== | == Operation == | ||
[[ | [[File:1wire.PNG|thumb|400px|1-Wire extension module]] | ||
After the sensors are connected to the controller, they appear in the Devices, column 1-wire Thermometers. | |||
== Известные ошибки и особенности == | == Известные ошибки и особенности == |
Версия 10:56, 27 июня 2019
Hardware
The module contains GPIO protection, an active 1-Wire line pull-up and a current limiter at 5Vout.
Pinout
The signals are output to the O1-O3 terminals of the extension module.
Pinout:
Terminal | Function |
---|---|
O1 | 5Vout |
O2 | 1-W |
O3 | GND |
Configuration
Configuration is set in the web interface under Configs => Hardware Modules Configuration.
In the Internal slot 1 or 2 section (depending on the slot number) select "WBE2-I-1-WIRE" and click Save.
The device is detected immediately, no reboot is required. After adding the device the output of the dmesg command will display a message i2c-gpio mod1_i2c: using pins 24 (SDA) and 25 (SCL)
Operation
After the sensors are connected to the controller, they appear in the Devices, column 1-wire Thermometers.
Известные ошибки и особенности
ERRE21W01: Нестабильная работа с длинной линией
Подверженные устройства
WBE2-I-1-WIRE
Описание
См. https://support.wirenboard.com/t/problemy-s-wbe2-i-1-wire/2967
Модуль WBE2-I-1-WIRE на длинных линиях работает хуже, чем порты W1-W2 на Wiren Board 6.
Причины и подробное описание
Особенности работы применённой микросхемы DS2484 и схемы защиты. Схема защиты ограничивает фронты сигналов при работе активной подтяжки DS2484. Мастер шины DS2484 ошибочно включает активную подтяжку на длинной линии в момент передачи данных (active low) датчиками. Микросхема также имеет время маленькое время сэмплирования, из-за чего её работа более чувствительна к крутизне фронтов, и, следовательно, к длине линии.
Пути обхода
Использовать порты W1, W2 на Wiren Board 6 при возникновении проблем. Обратиться за гарантийной заменой на новую версию модуля.
Запланированное исправление
Не планируется. WBE2-I-1WIRE снят с производство, к выходу планируется модуль WBE2-I-1WIRE-V2, не имеющий этой проблемы.