WBIO-DI-DR-16 I/O Module/en: различия между версиями
(Новая страница: «300px|thumb|right|Dimensions») |
(Новая страница: «== Connection to controller == See section Модули_ввода-вывода/en#Activating the modules in the controller web interface|activating the module…») |
||
Строка 72: | Строка 72: | ||
[[File:DIN 3U.png |300px|thumb|right|Dimensions]] | [[File:DIN 3U.png |300px|thumb|right|Dimensions]] | ||
== | == Connection to controller == | ||
See section [[Модули_ввода-вывода/en#Activating the modules in the controller web interface|activating the module in the web interface of the controller]]. | |||
controls like EXT'''x'''_DR('''1-16''') appear in Discrete I/O device, corresponding to the inputs of the module. Corresponding MQTT topics (read-only) look like: /devices/wb-gpio/controls/EXT'''x'''_DR'''y'''. | |||
== Подключение устройств == | == Подключение устройств == |
Версия 17:22, 3 июля 2019
This model is discontinued. Recommended replacement is WBIO-DI-WD-14 Buy WBIO-DI-WD-14 online
Purpose
Connection of pulse counters, buttons, switches, sensors with dry contact output.
Technical specifications
It contains 16 inputs for connection of dry contacts, united in two groups of 8 inputs with group galvanic isolation. The scheme of inputs is shown in the figure. The terminal is supplied with a voltage of 4.5 — 5.5 V, a small current flows to the ground (1-2 mA), causing the operation of the input.
Parameter | Value |
---|---|
Number of inputs | 16 |
Isolated input groups | 2 |
Input type | dry contact,
the opening by the current at earth fault |
Operation condition | GND input lockout |
Tripping current | 1 mA |
Minimum pulse width to trigger | 10 MS |
Minimum time between consecutive signals | 5 MS |
Voltage "wetting" | 4.5 V |
Module type | "I" (inverted address scheme) |
Maximum power consumption | 0.2 W |
Width, DIN units | 3 |
Size | 53,3x90,2x57,5 mm |
Terminals and wire section | |
---|---|
Recommended wire cross-section with TSVI, mm2 | 0,75 — 1 |
Length of the standard sleeve NSVE, mm | 8 (10 for adjusting screwless terminal blocks) |
Torque of screws, N∙m | 0,2 (for screw terminals) |
Connection to controller
See section activating the module in the web interface of the controller. controls like EXTx_DR(1-16) appear in Discrete I/O device, corresponding to the inputs of the module. Corresponding MQTT topics (read-only) look like: /devices/wb-gpio/controls/EXTx_DRy.
Подключение устройств
Датчики/счетчики с импульсными выходами/кнопки.
Такие устройства формируют сигнал, замыкая подходящие к ним два провода. Подключите один провод к клемме GND модуля. Второй провод подключите к клемме Dx. Через кнопку протекает ток менее 2 мА. Некоторые счетчики имеют импульсный выход на оптроне, тогда два провода имеют полярность - "плюс" и "минус". В таком случае минус подключается к GND, "плюс" к Dx.
Устройства с выходом "открытый коллектор".
Устройство и модуль должны иметь общую землю. Выход "открытый коллектор" подключите к клемме Dx.
Входы модуля гальванически развязаны от контроллера. Поэтому земли GND модуля и контроллера могут быть разными.
Обратите внимание, что для подключения устройств ко входам 1 — 8 используются клеммники GND верхнего ряда, а для входов 9 — 16 — нижнего.
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WBIO-DI-DR-16.
Corel Draw 2018: WBIO-DI-DR-16.cdr.zip
Corel Draw PDF: WBIO-DI-DR-16.cdr.pdf
Autocad 2013 DXF: WBIO-DI-DR-16.dxf.zip
Autocad PDF: WBIO-DI-DR-16.pdf