Первое включение Wiren Board Smart Home/en: различия между версиями
(Новая страница: «== Preparing to power on ==») |
(Новая страница: «Before work #Be sure to insert the software image microSD card (included) into the device. #Install a micro SIM card (if you plan to use a GSM module). #Check the…») |
||
Строка 5: | Строка 5: | ||
== Preparing to power on == | == Preparing to power on == | ||
Before work | |||
# | #Be sure to insert the software image microSD card (included) into the device. | ||
# | #Install a micro SIM card (if you plan to use a GSM module). | ||
# | #Check the switch position. | ||
# | #Connect the power supply. | ||
=== microSD | === microSD card === | ||
Installed in the connector for memory card ('''top''') contacts '''up'''. | |||
=== Micro-SIM | === Micro-SIM card === | ||
It is installed in the connector for Micro-SIM card ("lower") contacts '''down''' cut corner inside. | |||
=== | === Switch position === | ||
The pressed side with a dot is 'off'. | |||
=== | === Power supply === | ||
There are three types: standard, DIN-rail, PoE-injector. | |||
''' | '''Do not connect two different power supplies at the same time''', it will burn them and the controller. | ||
The standard power supply is connected to the appropriate connector. | |||
The power supply on a DIN rail connect the wires to the big terminals Vin and Gnd (next to the relays, see diagram http://contactless.ru/wiki/index.php/%D0%A4%D0%B0%D0%B9%D0%BB:WB3.5.png) | |||
The Passive PoE power supply is connected by an Ethernet cable. | |||
=== Подключение антенн === | === Подключение антенн === |
Версия 13:02, 19 июля 2019
"'This article is relevant for wiren Board 3.5"' [Problem with memory cards in the first batch of devices]
Preparing to power on
Before work
- Be sure to insert the software image microSD card (included) into the device.
- Install a micro SIM card (if you plan to use a GSM module).
- Check the switch position.
- Connect the power supply.
microSD card
Installed in the connector for memory card (top) contacts up.
Micro-SIM card
It is installed in the connector for Micro-SIM card ("lower") contacts down cut corner inside.
Switch position
The pressed side with a dot is 'off'.
Power supply
There are three types: standard, DIN-rail, PoE-injector. Do not connect two different power supplies at the same time, it will burn them and the controller. The standard power supply is connected to the appropriate connector. The power supply on a DIN rail connect the wires to the big terminals Vin and Gnd (next to the relays, see diagram http://contactless.ru/wiki/index.php/%D0%A4%D0%B0%D0%B9%D0%BB:WB3.5.png) The Passive PoE power supply is connected by an Ethernet cable.
Подключение антенн
В стандартной комплектации контролер идет с подключенной внутренней антенной Wi-Fi, радио 433 и внешней антенной GSM на SMA разъем (в первой партии поставлялись с внутренней антенной GSM).
Для подключения внешних антенн используйте переходники с u.fl на SMA. Расположение u.fl разъемов GSM и Wi-Fi см. фото на странице описания.
u.fl разъем для внешней антенны на 433 Мгц расположен рядом с основанием штыревой антенны, при подключении внешней, отпаяйте/откусите внутреннею штыревую антенну.
При слабом сигнале сотовой сети возможна нестабильная работа контроллера с внутренней антенной GSM. Используйте внешнею и располагайте ее вдалеке от контроллера.
Первое включение
Первое включение устройства может занять длительное время (3-4 минуты). При первом включении происходит создание секретных ключей для ssh и производится инициализация серийного номера устройства.
IP-адрес
При подключении по Ethernet Wiren Board Smart Home автоматически получает IP-адрес по DHCP. Узнать IP-адрес, который получило устройство можно в списке подключенных клиентов в административном интерфейсе вашего роутера.
Доступ по SSH и консоль
Стандартные имя пользователя и пароль: пользователь: root, пароль wirenboard
Обновление ПО
Рекомендуем выполнить обновление ПО. См. http://contactless.ru/forums/topic/%D0%BE%D0%B1%D0%BD%D0%BE%D0%B2%D0%BB%D0%B5%D0%BD%D0%B8%D1%8F-%D0%BF%D0%BE/