Firmware Changelog: различия между версиями
N.kulikov (обсуждение | вклад) |
Garik (обсуждение | вклад) |
||
Строка 20: | Строка 20: | ||
|06-08-2020 | |06-08-2020 | ||
|[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MR/stable/1.15.0/ 1.15.0] | |[http://fw-releases.wirenboard.com/?prefix=fw/by-version/WB-MR/stable/1.15.0/ 1.15.0] | ||
| | |ALL | ||
|Add inputs frequency measurement | |Add inputs frequency measurement | ||
|- | |- | ||
Строка 68: | Строка 68: | ||
|24-12-2019 | |24-12-2019 | ||
|1.5.1 | |1.5.1 | ||
| | |ALL | ||
|change build system use make | |change build system use make | ||
|- | |- | ||
Строка 74: | Строка 74: | ||
|25-11-2019 | |25-11-2019 | ||
|1.14.1 | |1.14.1 | ||
| | |ALL | ||
|change build system use make | |change build system use make | ||
|- | |- | ||
Строка 121: | Строка 121: | ||
|2.2.0 | |2.2.0 | ||
|WB-MAP3E, WB-MAP3H, WB-MAP6S, WB-MAP12H | |WB-MAP3E, WB-MAP3H, WB-MAP6S, WB-MAP12H | ||
| | |Eeprom and perith submodules. RAM optimisation. Work with bootloader. | ||
|- | |- | ||
|WB-MCM | |WB-MCM | ||
Строка 127: | Строка 127: | ||
|1.1.0 | |1.1.0 | ||
|WB-MCM8 | |WB-MCM8 | ||
| | |Work with bootloader 1.1.0 - support hw watchdog. | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 133: | Строка 133: | ||
|4.8.0 | |4.8.0 | ||
|ALL | |ALL | ||
| | |Work with bootloader 1.1.0 - support hw watchdog. use submodules. | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 139: | Строка 139: | ||
|4.7.0 | |4.7.0 | ||
|WB-MSWv3 | |WB-MSWv3 | ||
| | |Added STM32F030 mcu. IR module disabled. Use MS bootloader target. | ||
|- | |- | ||
|WB-MIO | |WB-MIO | ||
|15-08-2019 | |15-08-2019 | ||
|1.5.0 | |1.5.0 | ||
| | |ALL | ||
| | |Bootloader support | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 151: | Строка 151: | ||
|4.6.1 | |4.6.1 | ||
|WB-V2 | |WB-V2 | ||
| | |Added support of MS v2 sensor with another coefficients for adc to measure lux using OSRAM_BPW34S sensor. | ||
|- | |- | ||
|WB-MR | |WB-MR | ||
Строка 157: | Строка 157: | ||
|1.12.0 | |1.12.0 | ||
|WB-MR*, WB-MWAC | |WB-MR*, WB-MWAC | ||
| | |Default input mode switch (1) | ||
|- | |- | ||
|WB-MCM | |WB-MCM | ||
Строка 163: | Строка 163: | ||
|1.0.0 | |1.0.0 | ||
|WB-MCM8 | |WB-MCM8 | ||
| | |Initial firmware version: 32-bit EEPROM-stored counters; digital inputs LED indication | ||
|- | |- | ||
|WB-MR | |WB-MR | ||
Строка 169: | Строка 169: | ||
|1.11.1 | |1.11.1 | ||
|WB-MR*, WB-MWAC | |WB-MR*, WB-MWAC | ||
| | |Fix invalid inputs state in discrete registers after startup | ||
|- | |- | ||
|- | |- | ||
Строка 176: | Строка 176: | ||
|4.6.0 | |4.6.0 | ||
|WB-MIR, WB-M1W2 | |WB-MIR, WB-M1W2 | ||
| | |Added w1 temperature registers without invalid state - it save previous valid (20 - 21) | ||
added w1 channels status discret regs (16 - 17) | added w1 channels status discret regs (16 - 17) | ||
|- | |- | ||
Строка 184: | Строка 184: | ||
|WB-MS, WB-MSW v.3, WB-MIR, | |WB-MS, WB-MSW v.3, WB-MIR, | ||
WB-M1W2, WB-MAI2-mini/cc | WB-M1W2, WB-MAI2-mini/cc | ||
| | |Support [[WB-MCU-Flasher|firmware update]] | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 190: | Строка 190: | ||
|4.4.0 | |4.4.0 | ||
|WB-MIR | |WB-MIR | ||
| | |Mir64 version with 40 ir codes cells | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 196: | Строка 196: | ||
|4.3.0 | |4.3.0 | ||
|WB-MIR | |WB-MIR | ||
| | |More robust IR commands storage (i.e. without flash fs and compression), as in fw < 3.7.2 | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 202: | Строка 202: | ||
|4.2.0 | |4.2.0 | ||
|WB-MSW v.3 | |WB-MSW v.3 | ||
|* | |* Added: support for MSW v.3 hw rev 4.8 | ||
<nowiki>*</nowiki> added: temperature and relative humidity x100 value to 4 and 5 registers | <nowiki>*</nowiki> added: temperature and relative humidity x100 value to 4 and 5 registers | ||
Строка 215: | Строка 215: | ||
|1.10.0 | |1.10.0 | ||
|WB-MR*, WB-MWAC | |WB-MR*, WB-MWAC | ||
| | |Support [[WB-MCU-Flasher|firmware update]] |- | ||
|- | |- | ||
|WB-MRGB | |WB-MRGB | ||
Строка 221: | Строка 221: | ||
|1.2.0 | |1.2.0 | ||
|WB-MRGB-D | |WB-MRGB-D | ||
| | |Support [[WB-MCU-Flasher|firmware update]] | ||
|- | |- | ||
|WB-MR | |WB-MR | ||
Строка 227: | Строка 227: | ||
|1.9.4 | |1.9.4 | ||
|WB-MR*, WB-MWAC | |WB-MR*, WB-MWAC | ||
|* | |* Change: fix change modbus id via broadcast 0 address | ||
|- | |- | ||
|WB-MR | |WB-MR | ||
Строка 241: | Строка 241: | ||
|WB-MR*, WB-MWAC | |WB-MR*, WB-MWAC | ||
| | | | ||
* | * More robust configuration storage in EEPROM | ||
* | * Change: I2C EEPROM ic is used to store basic configuration. | ||
* | * Added: new input-output relationship handling is implemented: there is a new input mode which tells the fw to use so called input mappings to decide what to do on input state change. This mapping, distinct for each input-output pair, allows to set actions for both rising and falling edges of input signal. The actions are: set output, reset output, toggle output, do nothing. | ||
* | * Change: Kill-switch function is basically removed. It replaced with simplified input mode 2 which switches off all output channels on rising edge of the signal. | ||
* | * Added: WB-MWAC water leak controller is supported | ||
|- | |- | ||
|WB-MRGB | |WB-MRGB | ||
Строка 251: | Строка 251: | ||
|1.1.3 | |1.1.3 | ||
|WB-MRGBW-D | |WB-MRGBW-D | ||
|* | |* Change: fix change modbus id via broadcast 0 address (fixes ERRMRGBWD0001) | ||
|- | |- | ||
|WB-MAP | |WB-MAP | ||
Строка 297: | Строка 297: | ||
|4.1.0 | |4.1.0 | ||
|WB-MSW v.3 | |WB-MSW v.3 | ||
|* | |* Note: MSW v.3 VOC-sensor related fixes and improvenets | ||
<nowiki>*</nowiki> added: input register 106 with current valid SGPC3 baseline reported by the sensor | <nowiki>*</nowiki> added: input register 106 with current valid SGPC3 baseline reported by the sensor | ||
Строка 308: | Строка 308: | ||
|4.0.1 | |4.0.1 | ||
|WB-MSW v.3 | |WB-MSW v.3 | ||
|* | |* Added: improve SPL metering on WB-MSW v.3 | ||
|- | |- | ||
|WB-MS | |WB-MS | ||
Строка 315: | Строка 315: | ||
|WB-MS, WB-MSW v.3, WB-MIR, | |WB-MS, WB-MSW v.3, WB-MIR, | ||
WB-M1W2, WB-MAI2-mini/cc | WB-M1W2, WB-MAI2-mini/cc | ||
|* | |* Added: add new target for WB-MSW v3 | ||
<nowiki>*</nowiki> added: add PIR movement sensor support | <nowiki>*</nowiki> added: add PIR movement sensor support | ||
Строка 332: | Строка 332: | ||
|3.12.2 | |3.12.2 | ||
|WB-MAI2-mini/CC | |WB-MAI2-mini/CC | ||
| | |Add support for WB-MAI2-mini/CC | ||
|- | |- | ||
Строка 339: | Строка 339: | ||
| 3.12.1 | | 3.12.1 | ||
| WB-MIR, WB-M1W2 | | WB-MIR, WB-M1W2 | ||
| * | | * Change: fixes NTC heating compensation | ||
* | * Note NTC compersation value was damaged while saving/restoring from flash | ||
|- | |- | ||
Строка 347: | Строка 347: | ||
| 3.12 | | 3.12 | ||
| WB-MSW2 | | WB-MSW2 | ||
| * | | * Change: fixes NTC heating compensation | ||
* | * Change: add <censored> new CO2 sensor support to MSW2_3.4 boards | ||
* | * Fixes modbus integrity check | ||
* | * Checklist:add manual calibration for <censored> | ||
* | * Checklist:add zero calibration (manual calibration to 400ppm) | ||
* | * Note: - Write 1 to coilreg (COIL_REG_CO2_SENS_CALIBRATE_ZERO) 1 to fresh air calibrate any CO2 sensor | ||
(At <censored> the 1 value at coilreg remains 1 for 3 sec and then = 0) | (At <censored> the 1 value at coilreg remains 1 for 3 sec and then = 0) | ||
- Wrtie 1 to holdreg (HOLD_REG_CO2_SENS_ABC_CALIBRATION) 95 to CLOSE CO2 sensor ABC calib/ 0 = OPEN | - Wrtie 1 to holdreg (HOLD_REG_CO2_SENS_ABC_CALIBRATION) 95 to CLOSE CO2 sensor ABC calib/ 0 = OPEN | ||
Строка 366: | Строка 366: | ||
| 3.11.2 | | 3.11.2 | ||
| WB-MS, WB-MSW, WB-MIR, WB-M1W2 | | WB-MS, WB-MSW, WB-MIR, WB-M1W2 | ||
| * | | * Change: bug fix: writing single hold reg value > 125 resulted modbus illegal data value error | ||
|- | |- | ||
Строка 373: | Строка 373: | ||
| 3.11.1 | | 3.11.1 | ||
| WB-MS, WB-MSW, WB-MIR, WB-M1W2 | | WB-MS, WB-MSW, WB-MIR, WB-M1W2 | ||
| * | | * Change: add modbus package integrity testing to "mb_recive_hadler" function | ||
* | * Note: - returns with modbus error "MB_ERROR_ILLEGAL_DATA_VALUE" if a package includes a write CRC but wrong package size or fields | ||
- returns with modbus error "MB_ERROR_ILLEGAL_DATA_VALUE" if requested size of data is greater than allowed (125 at reading, 123 at | - returns with modbus error "MB_ERROR_ILLEGAL_DATA_VALUE" if requested size of data is greater than allowed (125 at reading, 123 at | ||
writing but at writing technically not possible to get receive such command due to the limited RX buffer size) | writing but at writing technically not possible to get receive such command due to the limited RX buffer size) | ||
Строка 390: | Строка 390: | ||
| 3.10.0 | | 3.10.0 | ||
| WB-MS, WB-M1W2, WB-MIR | | WB-MS, WB-M1W2, WB-MIR | ||
| | | Added filter out algorithm for suspicious values 85C and 127.937C from 1-wire temperature sensors | ||
|- | |- | ||
|WB-MRGB | |WB-MRGB | ||
Строка 399: | Строка 399: | ||
* Storing configs and device state in external eeprom | * Storing configs and device state in external eeprom | ||
* Watchdog enable | * Watchdog enable | ||
* | * Change: add MRGBW support | ||
* | * Note: modbus hold reg 3 = white channel value | ||
modbus hold reg 8 = button 3 value | modbus hold reg 8 = button 3 value | ||
button3 short press = on/off white channel | button3 short press = on/off white channel | ||
button3 long press = adjust brightness of white channel | button3 long press = adjust brightness of white channel | ||
modbus hold reg 33 = button 3 counter | modbus hold reg 33 = button 3 counter | ||
* | * Change: "BUTTON_DISABLED" register state is stored/restored to eeprom | ||
* | * Change: Effectless "color changed over modbus" feature removed | ||
|- | |- | ||
Строка 413: | Строка 413: | ||
| 1.1 | | 1.1 | ||
| WB-MAP3H, WB-MAP3E, WB-MAP6S, WB-MAP12H | | WB-MAP3H, WB-MAP3E, WB-MAP6S, WB-MAP12H | ||
| | | Add support for WB-MAP3 devices | ||
|} | |} |
Версия 16:52, 24 августа 2020
Updating firmware
Please see this page for details. Firmware binaries are available on fw-releases.wirenboard.com.
Общая таблица по всем устройствам/ Summary table for all devices
Source project | Release date | Version | Affected devices | Changelog |
---|---|---|---|---|
WB-MR | 06-08-2020 | 1.15.0 | ALL | Add inputs frequency measurement |
WB-MS | 26-06-2020 | 4.13.0 | WB-MIR WB-MIR64 WB-M1W2 WB-M1W2_V2_1 | Fix compensation internal ntc temperature sensor. |
WB-MS | 23-04-2020 | 4.12.0 | WB-MSW v.3 | Improve TH sensor work. Read errors filtration. |
WB-MD | 04-04-2020 | 2.2.0 | WB-MDM3 | add switch mode, mode selection by hold reg 50-52 (value 2) |
WB-MS | 01-04-2020 | 4.11.0 | WB-MSW v.3 | Improve CO2 sensor work. Read settings from sensor. |
WB-MD | 19-03-2020 | 2.1.0 | WB-MDM3 | Two modbus holding registers 140 and 150 were added for setting the variable dimming duration |
WB-MAP | 10-03-2020 | 2.2.5 | MAP12H,MAP3E,MAP3H,MAP6S | Fix FRAM configuration loss |
WB-MS | 19-03-2020 | 4.10.0 | WB-M1W2 | M1W2 v1.2 with active pullup support |
WB-MIO | 24-12-2019 | 1.5.1 | ALL | change build system use make |
WB-MR | 25-11-2019 | 1.14.1 | ALL | change build system use make |
WB-MR | 25-11-2019 | 1.14.0 | WB-MR6CU | new model MR6CU compact 2 unit 6 channel 7A relay without inputs |
WB-MAP | 14-11-2019 | 2.2.2 | MAP6S | Target for STM32F051K6 |
WB-MS | 12-11-2019 | 4.9.0 | WB-MSW v.3 |
|
WB-MR | 01-11-2019 | 1.13.1 | WB-MR2mini | fix input mode default value. add led in WB-MR2mini v2.1 |
WB-MR | 18-10-2019 | 1.13.0 | WB-MR2mini, WB-MR3, WB-MR6, WB-MR6C, WB-MWAC | variable debounce 0-100ms, reg 20+ |
WB-MRGB | 25-09-2019 | 1.3.0 | WB-MRGBW-D | work with bootloader 1.1.0 - support hw watchdog. |
WB-MAP | 10-09-2019 | 2.2.0 | WB-MAP3E, WB-MAP3H, WB-MAP6S, WB-MAP12H | Eeprom and perith submodules. RAM optimisation. Work with bootloader. |
WB-MCM | 27-09-2019 | 1.1.0 | WB-MCM8 | Work with bootloader 1.1.0 - support hw watchdog. |
WB-MS | 19-09-2019 | 4.8.0 | ALL | Work with bootloader 1.1.0 - support hw watchdog. use submodules. |
WB-MS | 06-09-2019 | 4.7.0 | WB-MSWv3 | Added STM32F030 mcu. IR module disabled. Use MS bootloader target. |
WB-MIO | 15-08-2019 | 1.5.0 | ALL | Bootloader support |
WB-MS | 13-06-2019 | 4.6.1 | WB-V2 | Added support of MS v2 sensor with another coefficients for adc to measure lux using OSRAM_BPW34S sensor. |
WB-MR | 13-06-2019 | 1.12.0 | WB-MR*, WB-MWAC | Default input mode switch (1) |
WB-MCM | 28-05-2019 | 1.0.0 | WB-MCM8 | Initial firmware version: 32-bit EEPROM-stored counters; digital inputs LED indication |
WB-MR | 17-05-2019 | 1.11.1 | WB-MR*, WB-MWAC | Fix invalid inputs state in discrete registers after startup |
WB-MS | 22-03-2019 | 4.6.0 | WB-MIR, WB-M1W2 | Added w1 temperature registers without invalid state - it save previous valid (20 - 21)
added w1 channels status discret regs (16 - 17) |
WB-MS | 04-03-2019 | 4.5.0 | WB-MS, WB-MSW v.3, WB-MIR,
WB-M1W2, WB-MAI2-mini/cc |
Support firmware update |
WB-MS | 27-02-2019 | 4.4.0 | WB-MIR | Mir64 version with 40 ir codes cells |
WB-MS | 11-02-2018 | 4.3.0 | WB-MIR | More robust IR commands storage (i.e. without flash fs and compression), as in fw < 3.7.2 |
WB-MS | 11-02-2019 | 4.2.0 | WB-MSW v.3 | * Added: support for MSW v.3 hw rev 4.8
* added: temperature and relative humidity x100 value to 4 and 5 registers * added: temperature and relative humidity self-heat compensation 245 register 1x100 *C * added: new register 108: SGPC3 sensor version. 0xFFFF is sensor is missing on power-up * change: sgpc3: ignoring data during 3 minutes after warm up (total 364 seconds after power up). |
WB-MR | 04-03-2019 | 1.10.0 | WB-MR*, WB-MWAC | Support firmware update |- |
WB-MRGB | 2019-03-04 | 1.2.0 | WB-MRGB-D | Support firmware update |
WB-MR | 2019-02-14 | 1.9.4 | WB-MR*, WB-MWAC | * Change: fix change modbus id via broadcast 0 address |
WB-MR | 2018-11-14 | 1.9.2 | WB-MR*, WB-MWAC | Add check valid for readed from eeprom settings
Add check valid for modbus address when changed via modbus and when readed from eeprom |
WB-MR | 2018-11-14 | 1.9.1 | WB-MR*, WB-MWAC |
|
WB-MRGB | 2019-02-13 | 1.1.3 | WB-MRGBW-D | * Change: fix change modbus id via broadcast 0 address (fixes ERRMRGBWD0001) |
WB-MAP | 2019-02-03 | 2.1 | WB-MAP3H, WB-MAP3E, WB-MAP12H, WB-MAP6S | * change: WB-MAPs and CTs are now supposed to be calibrated separately.
Each CT is described by two parameters: (effective) turns ratio and phase delay. These parameters are to be programmed into WB-MAP registers to proper operation * change: phase angle is consistent between MAP3E and other models (-180..+180 notation) * added: 32-bit registers for voltage and current |
WB-MRGB | 2018-12-05 | 1.1.2 | WB-MRGBW-D |
* fix change modbus uart settings * change eeprom files to submodule. add neccesory defines. change project paths * move eeprom settings load/save to separate file. * move eeprom settings struct defines from config.h to settings.c. * add modbus id change valdation * add validation modbus settings when load from eeprom. * add validation for buttons disable, pwm divider and fade time settings * disable 1200 baud variant (need research why not work) |
WB-MDM2 | 1.1.0 | WB-MD2 | Two modbus holding registers 65 and 66 were added for users can choose 1 of 3 dimming curves: (0)incandecent bulbs, (1)LED bulbs, (2)resistive load | |
WB-MS | 4.1.0 | WB-MSW v.3 | * Note: MSW v.3 VOC-sensor related fixes and improvenets
* added: input register 106 with current valid SGPC3 baseline reported by the sensor * added: input register 107 with current raw signal * change: VOC sensor is initialized for 184s after power-on. During this time VOC registers return error value. | |
WB-MS | 4.0.1 | WB-MSW v.3 | * Added: improve SPL metering on WB-MSW v.3 | |
WB-MS | 4.0.0 | WB-MS, WB-MSW v.3, WB-MIR,
WB-M1W2, WB-MAI2-mini/cc |
* Added: add new target for WB-MSW v3
* added: add PIR movement sensor support * added: add SGPC3 air quality sensor support * added: add discrete input mode for 1-wire inputs with activation counters * added: improve SPL metering on WB-MS * change: improved config storage * fixes: workaround for IR bug | |
WB-MS | 3.12.2 | WB-MAI2-mini/CC | Add support for WB-MAI2-mini/CC | |
WB-MS | 3.12.1 | WB-MIR, WB-M1W2 | * Change: fixes NTC heating compensation
* Note NTC compersation value was damaged while saving/restoring from flash | |
WB-MS | 3.12 | WB-MSW2 | * Change: fixes NTC heating compensation
* Change: add <censored> new CO2 sensor support to MSW2_3.4 boards * Fixes modbus integrity check * Checklist:add manual calibration for <censored> * Checklist:add zero calibration (manual calibration to 400ppm) * Note: - Write 1 to coilreg (COIL_REG_CO2_SENS_CALIBRATE_ZERO) 1 to fresh air calibrate any CO2 sensor (At <censored> the 1 value at coilreg remains 1 for 3 sec and then = 0) - Wrtie 1 to holdreg (HOLD_REG_CO2_SENS_ABC_CALIBRATION) 95 to CLOSE CO2 sensor ABC calib/ 0 = OPEN At changing the parameter ABC cylce is also transmitted to sensor - Write any value between 400-1500 into () 88 to manually calibrate <censored> sensor Register content is automatically set to 0 after calibration. - Write 1-15 to holdreg () 89 to set ABC cycle (days). At setting the register OPEN/CLOSE state is also transmitted. | |
WB-MS | 3.11.2 | WB-MS, WB-MSW, WB-MIR, WB-M1W2 | * Change: bug fix: writing single hold reg value > 125 resulted modbus illegal data value error | |
WB-MS | 3.11.1 | WB-MS, WB-MSW, WB-MIR, WB-M1W2 | * Change: add modbus package integrity testing to "mb_recive_hadler" function
* Note: - returns with modbus error "MB_ERROR_ILLEGAL_DATA_VALUE" if a package includes a write CRC but wrong package size or fields - returns with modbus error "MB_ERROR_ILLEGAL_DATA_VALUE" if requested size of data is greater than allowed (125 at reading, 123 at writing but at writing technically not possible to get receive such command due to the limited RX buffer size) - returns with modbus error "MB_ERROR_ILLEGAL_FUNCTION" if modbus request function is unknow. | |
WB-MS | 3.10.1 | WB-MS, WB-M1W2, WB-MIR | 1-wire reset time changed from ~410 us to ~550 us. As in 1-Wire Standard, should be between 480 and 640 us | |
WB-MS | 3.10.0 | WB-MS, WB-M1W2, WB-MIR | Added filter out algorithm for suspicious values 85C and 127.937C from 1-wire temperature sensors | |
WB-MRGB | 1.1.1 | WB-MRGBW-D |
* Note: modbus hold reg 3 = white channel value modbus hold reg 8 = button 3 value button3 short press = on/off white channel button3 long press = adjust brightness of white channel modbus hold reg 33 = button 3 counter
| |
WB-MAP | 1.1 | WB-MAP3H, WB-MAP3E, WB-MAP6S, WB-MAP12H | Add support for WB-MAP3 devices |