SC16IS752/en: различия между версиями
(Новая страница: «The direction of operation of the transceiver is set by the chip using the RTS signal automatically, the hardware flow control must be disabled. RS-485 mode may n…») |
(Новая страница: «The device in Linux: <b>/dev/ttyNSC1</b>. Half-duplex RS-485-transceiver. RS-485 port-2 (the blue pair of terminals).») |
||
Строка 33: | Строка 33: | ||
===UART1=== | ===UART1=== | ||
The device in Linux: <b>/dev/ttyNSC1</b>. | |||
Half-duplex [[Special:MyLanguage/RS-485|RS-485]]-transceiver. RS-485 port-2 (the blue pair of terminals). | |||
Управляющие сигналы/GPIO, а также линии RX/TX выведены на разъём [[WB SH 3.5: UEXT2|WB SH 3.5: UEXT2]]. | Управляющие сигналы/GPIO, а также линии RX/TX выведены на разъём [[WB SH 3.5: UEXT2|WB SH 3.5: UEXT2]]. |
Версия 15:04, 25 апреля 2019
SC16IS752 is a chip that controls serial ports in some versions of the Wiren Board.
Description
SPI-to-UART bridge IC - NXP SC16IS752
two fully-functional UARTs with hardware flow control, up to 8 GPIOs.
Connected to SPI. GPIO is used as chip-select.
Linux uses the sc16is7x2 driver,which has not been ported to upstream yet. It can be found in our Linux repository [1]. The driver is included in the standard image.
GPIO
sc16is7x2 driver exports 8 GPIOs into the standard Linux sysfs-interface under numbers 120-127.
In Wiren Board Smart Home 3.5
UART0
The device in Linux: /dev/ttyNSC0. Half-duplex RS-485-transceiver. RS-485 port-1 (the green pair of terminals).
The direction of operation of the transceiver is set by the chip using the RTS signal automatically, the hardware flow control must be disabled. RS-485 mode may need to be activated from the userspace in future versions of the driver.
UART1
The device in Linux: /dev/ttyNSC1. Half-duplex RS-485-transceiver. RS-485 port-2 (the blue pair of terminals).
Управляющие сигналы/GPIO, а также линии RX/TX выведены на разъём WB SH 3.5: UEXT2. Разъём предназначен для использования GPIO, а также для подключения модуля расширения RS232.
В Wiren Board 2.8
UART0
Устройство в Linux: /dev/ttyNSC0. TX/RX линии порта выведены на разъём UEXT UEXT2. Параллельно к ним подключен полудуплексный RS-485-трансивер (если есть). Направление работы трансивер задаётся чипом с помощью сигнала RTS автоматически, аппаратный контроль потока должен быть отключен. В следующих версиях драйвера, режим RS-485 возможно будет необходимо активировать из userspace.
UART1
Порт /dev/ttyNSC1 в Linux. К TX/RX-линиям порта подключен GPS-модуль SIM68V.
GPIO
7 линий GPIO выведены на отверстия с шагом 2.54 на плате Wiren Board. К одной из линий GPIO подключен сигнал PPS с GPS-модема.
Драйвер sc16is7x2 экспортирует 8 GPIO в стандартный sysfs-интерфейс Linux под номерами 120-127.