Translations:Wiren Board 6.7: Peripherals/4/en: различия между версиями
Matveevrj (обсуждение | вклад) |
Matveevrj (обсуждение | вклад) |
||
| Строка 12: | Строка 12: | ||
|/dev/ttymxc1 | |/dev/ttymxc1 | ||
|/dev/ttyRS485-1 | |/dev/ttyRS485-1 | ||
| Signed | | Signed ''RS-485'', terminal blocks A and B | ||
| Uninsulated port, terminator installed | | Uninsulated port, terminator installed | ||
|- | |- | ||
|/dev/ttymxc3 | |/dev/ttymxc3 | ||
|/dev/ttyRS485-2 | |/dev/ttyRS485-2 | ||
| Signed | | Signed ''RS-485'', terminal blocks A/L and B/H (this port can be used as CAN) | ||
| Uninsulated port, terminator installed, multiplexed with CAN | | Uninsulated port, terminator installed, multiplexed with CAN | ||
|- | |- | ||
| Строка 23: | Строка 23: | ||
|/dev/ttyMOD1 | |/dev/ttyMOD1 | ||
| UART on the extension module MOD1 | | UART on the extension module MOD1 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc4 | |/dev/ttymxc4 | ||
|/dev/ttyMOD2 | |/dev/ttyMOD2 | ||
| UART on the extension module MOD2 | | UART on the extension module MOD2 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc5 | |/dev/ttymxc5 | ||
|/dev/ttyMOD3 | |/dev/ttyMOD3 | ||
| UART on the extension module MOD3 | | UART on the extension module MOD3 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc6 | |/dev/ttymxc6 | ||
|/dev/ttyMOD4 | |/dev/ttyMOD4 | ||
| UART on the extension module MOD4 | | UART on the extension module MOD4 | ||
| To appear, you need to set in wb-hardware.conf | | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» | ||
|- | |- | ||
|/dev/ttymxc7 | |/dev/ttymxc7 | ||
Текущая версия на 22:43, 28 сентября 2022
| Port Name in Linux | Alternate Port Name on Linux | Connector on controller | Note |
| /dev/ttymxc0 | /dev/ttyCONSOLE | Controller debug-uart (micro-usb) | Default Settings: 115200-8-N-1 |
| /dev/ttymxc1 | /dev/ttyRS485-1 | Signed RS-485, terminal blocks A and B | Uninsulated port, terminator installed |
| /dev/ttymxc3 | /dev/ttyRS485-2 | Signed RS-485, terminal blocks A/L and B/H (this port can be used as CAN) | Uninsulated port, terminator installed, multiplexed with CAN |
| /dev/ttymxc2 | /dev/ttyMOD1 | UART on the extension module MOD1 | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» |
| /dev/ttymxc4 | /dev/ttyMOD2 | UART on the extension module MOD2 | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» |
| /dev/ttymxc5 | /dev/ttyMOD3 | UART on the extension module MOD3 | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» |
| /dev/ttymxc6 | /dev/ttyMOD4 | UART on the extension module MOD4 | To appear, you need to set in wb-hardware.conf «Expose UART Pins (DIY)» |
| /dev/ttymxc7 | /dev/ttyGSM | UART on WBC expansion module (GSM/3G/4G modem connector) | To appear, you need to set any of the modems in wb-hardware.conf |