16 808
правок
(Новая страница: «To change the device's address, connect to the controller via SSH.») |
|||
(не показано 5 промежуточных версий этого же участника) | |||
Строка 110: | Строка 110: | ||
To change the device's address, connect to the controller via [[SSH]]. | To change the device's address, connect to the controller via [[SSH]]. | ||
# Install the utility using the command: | |||
# | |||
#:<syntaxhighlight lang="bash"> | #:<syntaxhighlight lang="bash"> | ||
apt update && apt install wb-modbus-ext-scanner | apt update && apt install wb-modbus-ext-scanner | ||
</syntaxhighlight> | </syntaxhighlight> | ||
# | # Stop the wb-mqtt-serial driver using the command: | ||
#:<syntaxhighlight lang="bash"> | #:<syntaxhighlight lang="bash"> | ||
systemctl stop wb-mqtt-serial | systemctl stop wb-mqtt-serial | ||
</syntaxhighlight> | </syntaxhighlight> | ||
# | # Execute the command: | ||
#:<syntaxhighlight lang="bash"> | #:<syntaxhighlight lang="bash"> | ||
wb-modbus-scanner -d /dev/ttyRS485-1 -b 115200 -s 4267937719 -i 3 | wb-modbus-scanner -d /dev/ttyRS485-1 -b 115200 -s 4267937719 -i 3 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
# | # Where, /dev/ttyRS485-1 is the port to which the device is connected, 115200 is the exchange rate, 4267937719 is the device's serial number, 3 is the new slave ID. | ||
# As a result, the following output should appear: | |||
# | |||
#:<syntaxhighlight lang="bash"> | #:<syntaxhighlight lang="bash"> | ||
Serial port: /dev/ttyRS485-1 | Serial port: /dev/ttyRS485-1 | ||
Строка 133: | Строка 129: | ||
Change ID for device with serial 4267937719 [FE638FB7] New ID: 3 | Change ID for device with serial 4267937719 [FE638FB7] New ID: 3 | ||
</syntaxhighlight> | </syntaxhighlight> | ||
# | # Start the wb-mqtt-serial driver again using the command: | ||
#:<syntaxhighlight lang="bash"> | #:<syntaxhighlight lang="bash"> | ||
systemctl start wb-mqtt-serial | systemctl start wb-mqtt-serial | ||
</syntaxhighlight> | </syntaxhighlight> | ||
=== Support for scanning in firmware === | |||
{| border="1" class="wikitable" | |||
! Device || Firmware version where scanning was introduced | |||
|- | |- | ||
| WB-MRx, WB-MWAC | | WB-MRx, WB-MWAC | ||
| 1.19.0 | | 1.19.0 | ||
|- | |- | ||
| WB-MDM3 | | WB-MDM3 | ||
| 2.6.0 | | 2.6.0 | ||
|- | |- | ||
| WB-LED, WB-MRGBW-D | | WB-LED, WB-MRGBW-D | ||
| 3.2.0 | | 3.2.0 | ||
|- | |- | ||
| WB-MSx, WB-MSWx, WB-MIR, WB-M1W2 | | WB-MSx, WB-MSWx, WB-MIR, WB-M1W2 | ||
| 4.23.0 | | 4.23.0 | ||
|- | |- | ||
| WB-MAI11 | | WB-MAI11 | ||
| | | not supported | ||
|- | |- | ||
| WB-MAI6 | | WB-MAI6 | ||
| 2.0.0 | | 2.0.0 | ||
|- | |- | ||
| WB-MAO4 | | WB-MAO4 | ||
| 2.2.0 | | 2.2.0 | ||
|- | |- | ||
| WB-MAPx | | WB-MAPx | ||
| 2.4.0 | | 2.4.0 | ||
|- | |- | ||
| WB-MIO | | WB-MIO | ||
| 1.6.0 | | 1.6.0 | ||
|- | |- | ||
| WB-REF-U | | WB-REF-U | ||
| 1.4.0 | | 1.4.0 | ||
|- | |- | ||
| WB-REF-DF | | WB-REF-DF | ||
| 1.1.0 | | 1.1.0 | ||
|- | |- | ||
|} | |} | ||
==Useful links== | |||
* [https://habr.com/p/772308/ Upgrading Modbus: arbitration, bus scanning, events] - an article with details on implementing the extension | |||
* [https://habr.com/p/772308/ | * [https://github.com/wirenboard/wb-modbus-ext-scanner/blob/main/protocol.md Extension description on GitHub] | ||
* [https://github.com/wirenboard/wb-modbus-ext-scanner/blob/main/protocol.md | * [[Modbus | Modbus protocol description]] | ||
* [[Modbus | | * [https://github.com/wirenboard/wb-modbus-ext-scanner Scanning utility repository] | ||
* [https://github.com/wirenboard/wb-modbus-ext-scanner | |||