WB-MAI2-mini/CC
Purpose
WB-MAI2-mini/CC is a compact analog input module designed to measure current signal 4..20 mA via two independent channels. The module is controlled from the controller or PC via RS-485 bus by Modbus commands.
Specifications
Parameter | Value |
---|---|
Power | |
Supply voltage | 9 V – 28 V |
measurement Channels | |
Number of channels | 2 |
Current measurement | 0 – 20 mA |
Input impedance | A 49.9 Ohm |
Current measurement error | ±1% |
Control | |
Management interface | RS-485 |
Interface isolation | no |
Communication protocol | Modbus RTU, the address is set by software, factory settings are indicated on the label |
RS-485 interface parameters | Default speed of 9600 bps; data bits 8; parity N; stop bits 2.
Interface parameters can be configured programmatically:
|
Ready for operation after power supply | 1 c |
dimensions | |
Size | 57 x 18 x 14 mm |
operating Conditions | |
Air temperature | |
Relative humidity | up to 98%, without condensation |
Connection diagrams
The module is made in a compact housing and is designed for installation in solder boxes and cable channels.
The figure shows the connection diagram of sensors with a current output of 0-20 mA (4-20 mA). The internal resistance of the inputs — 49.9 Ohms.
Presentation in the web interface
The web interface for the module displays current values (controls "Current input 1 (mA)" and "Current input 2 (mA)"), supply voltage and serial number. The "CC" in the device name indicates that it supports two current inputs (Current).
Description of Modbus registers
All Modbus registers of the device are divided into 2 groups:
- General registers that define device parameters
- Registers of measured values
General registers
Register/ address | type | read-write | default | format | purpose |
---|---|---|---|---|---|
104-105 | input | R | 32-bit unsigned int | uptime counter in seconds | |
110 | holding | RW | 96 | baud rate / 100 | скорость порта RS-485, делённая на 100. Допустимые скорости: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 (Настройка параметров обмена данными по RS-485 для modbus-устройств Wiren Board) |
111 | holding | RW | 0 | настройка бита чётности порта RS-485. Допустимые значения: 0 - нет бита чётности (none), 1 - нечётный (odd), 2 - чётный (even) | |
112 | holding | RW | 2 | количество стоп-битов порта RS-485. Допустимые значения: 1, 2 | |
120 (0x78) | holding | RW | 0 | отличное от 0 | запись в регистр вызывает перезагрузку МК без сохранения состояния |
121 (0x79) | input | R | - | мВ | текущее напряжение питания модуля |
128 (0x80) | holding | RW | написан на наклейке на корпусе | Modbus-адрес устройства | |
200-206 | input | R | {'M','A','I','2','C','C'} | сигнатура устройства | |
220-241 | input | R | __date__ __time__ | дата сборки прошивки | |
250-269 | input | R | строка, null-terminated | версия прошивки | |
270-271 | input | R | 32-bit unsigned int | уникальный идентификатор (S/N) |
Регистры, содержащие значения измеряемых величин
Регистр / адрес (hex) | Тип | Разрядность | Порядок байтов | Формат | Множитель | Параметр | Назначение | Единицы измерения |
---|---|---|---|---|---|---|---|---|
246 | input | s16 | big endian | (value) | 3.125e-02 | Current input 1 (mA) | Ток канала 1 | мА |
247 | input | s16 | big endian | (value) | 3.125e-02 | Current input 2 (mA) | Ток канала 2 | мА |
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WB-MAI2-mini-CC.
Corel Draw 2018: WB-MAI2-mini_СС.cdr.zip
Corel Draw PDF: WB-MAI2-mini_СС.cdr.pdf
Autocad 2013 DXF: Мы еще не подготовили чертеж этого устройства. Вы можете запросить чертеж устройства "Analog input module WB-MAI2-mini/CC" на портале техподдержки Wiren Board (необходима регистрация).