История
23 сентября 2022
Нет описания правки
−4
Нет описания правки
−1
Нет описания правки
+1
Нет описания правки
Нет описания правки
+8
Нет описания правки
−11
21 сентября 2022
20 сентября 2022
Нет описания правки
+6
Нет описания правки
+22
Нет описания правки
−2
Новая страница: «Смотрите также: * ADC chanels of Wiren Board 6.2 * ADC chanels of Wiren Board 7 * ADC lists for older controller versions»
−108
Нет описания правки
−869
Нет описания правки
−2
Новая страница: «'''Analog inputs''' — ADC inputs used to measure the voltage applied to them. Analog inputs in automation devices are designed to connect sensors with an . analog output signal.»
−289
Новая страница: «{{DISPLAYTITLE: Analog inputs (ADC)}} == Определения == '''Analog to digital converters (ADC)''' — devices designed to convert input analog signals into digital code.»
−215
Обновление для соответствия новой версии исходной страницы.
+2298
25 июля 2022
Нет описания правки
+25
Нет описания правки
+19
Новая страница: «See also: * ADC channels in Wiren Board 6.2 * ADC lists for older controller versions»
−125
Новая страница: «== ADC list for WB6 controller ==»
−154
Новая страница: «Also, the value can be obtained in manual mode: Low-level work with ADC.»
−82
Новая страница: «The wb-homa-adc daemon translates the value to the MQQT message queue in the /devices/wb-adc/controls/Vin topic. Therefore, the value is displayed in the web interface as the Vin channel of the ADCs device»
−149
Новая страница: «== Input voltage ==»
−222
Новая страница: «#Voltage must be within acceptable range. #Ax terminal blocks perform two functions: ADC and low voltage load control. Before measuring voltage, set the corresponding low voltage load control output to the "off" position. For example, if you are connecting to terminal A1, disable A1_OUT in the web interface (section Relays & FETs). #Connect your source to the terminal. The voltage value will immediately appear in the Wired Board Web Interface | web interfa...»
−490
Обновление для соответствия новой версии исходной страницы.
−3185
24 мая 2019
15 мая 2019
Нет описания правки
+36
Новая страница: «{| border="1" | Terminal block || Divider|| Formula to recalculate || Final formula || comments |-»
−62
Новая страница: «{| border="1" | Terminal block || Divider || Formula to recalculate || Final formula (without divider) || V max. measured (with divider) || comments |- | A1-A8…»
−116
Новая страница: «| Vin || 33k/4k53 ||N / 4095 * 1.85V * 8.28 || V = N * 3.74 mV || 30V || input voltage, iio channel: 0 |-»
−22
Новая страница: «{| border="1" | Terminal block || Divider|| Formula to recalculate || Final formula || V max || comments |-»
−61
Новая страница: «| Vin || 33k/4k51 ||N / 4095 * 1.85V * 8.32 || V = N * 3.76 mV || 30.6V || input voltage, iio channel 0 |-»
−22
Новая страница: «| A1-A3 || 100k/90.9k || N / 4095 * 1.85V * 2.100 || V = N * 0.949 mV || 7.4V || |- | A4-A5 || 100k/11.86k || N / 4095 * 1.85V * 9.43 || V = N * 4.26 mV || 34.…»
−22
Новая страница: «{| border="1" | Terminal block || Divider || Formula to recalculate || Final formula (without divider) || V max. measured (with divider) || comments |-»
−94
Новая страница: «| 4В/li_pol || 7 || | V = N * 1.807 mV || - || on the 4 В line |- | Vin || 5 |88k7/12k|| V = N * 3.80 mV || 31V || inpit voltage |- |}»
−26
Новая страница: «{| border="1" class="wikitable" style="text-align:center" ! terminal block || ADC Channel (LRADCxx) || Divider|| Final formula (without divider) || V max. meas…»
−74
Новая страница: «See Wiren Board 6.2: Peripherals#Каналы АЦП»
−2
Новая страница: «=== A list of ADC for different devices ===»
−23
Новая страница: «A part of the ADC channels is output to the terminals in parallel with the low-voltage load control transistors. '''Make sure''' you have closed the corresponding…»
−190
Новая страница: «=== The main channels ===»
−11
Новая страница: «In Wiren Board 6, the ADC channels of the processor are connected to terminals A1-A4. Also, the ADC has input voltage (after the input diodes) and voltage at the…»
−98
Новая страница: «The ADC channels serving the R1 and R2 inputs have a built-in independent current source that is used to measure the resistance connected to the channel. Current…»
−198
Новая страница: «The Wiren Board 5 uses 8 different ADC channels that are connected to separate processor channels. The 4V line is connected to the BAT channel (LRADC7), in additi…»
−188
Новая страница: «Wiren Board сontrollers versions 2.3 and 4 have 8 ADC channels that are multiplexed into one processor channel (LRADC1). Multiplexing channels are shown in the t…»
−94
Новая страница: «== Technical details on the implementation of the ADC ==»
−13
перевести статью по ссылке
−62
Новая страница: «The wb-homa-adc daemon translates the value to the MQTT message queue in the topic /devices/wb-adc/controls/BAT. Therefore, the value is displayed in the web inte…»
−92